SMC CJPS16 15Z T Pin Cylinder User Guide
- June 17, 2024
- SMC
Table of Contents
SMC CJPS16 15Z T Pin Cylinder
The Pin Cylinder is a single-acting, spring return cylinder with a shorter overall length. It is designed to be recessed directly into a machine or installed on a panel, making the machine more compact and reducing installation space. The cylinder is RoHS-compliant.
Overall length
A short-stroke miniature cylinder with a shorter.
The installation space can be significantly reduced because this cylinder can
be recessed directly into a machine or installed on a panel. Thus, the machine
can be made more compact.
Application Examples
Rod end cap can now be ordered with the cylinder.
It is not necessary to order a rod end cap for the applicable cylinder
separately.
Applicable for the change of the rod end shape ( -XA ) (Simple Specials).
One-touch fitting can be connected. (Panel mount type)
Ø 2 One-touch fitting, miniature fitting, and speed controller can be
connected.
16 mm bore size is now available.
(Changed from the existing product: 15 mm) Specifications and dimensions are
the same as the existing product.
Pin Cylinder: Single Acting, Spring Return
How to Order
Symbol
Single acting, Spring return
Made to Order (Ø 6 to Ø 16)
(For details, refer to pages 6 and 7.)
Symbol | Specifications |
---|---|
XA □ | Change of rod end shape |
XC17 | Pin cylinder with rod quenched |
XC22 | Fluororubber seals |
Moisture Control Tube
IDK Series
When operating an actuator with a small diameter and a short stroke at a high frequency, dew condensation (water droplets) may occur inside the piping depending on the conditions. Simply connecting the moisture control tube to the actuator will prevent dew condensation from occurring. For details, refer to the Catalogue on https://www.smc.eu.
Specifications
Action | Single acting, Spring return |
---|---|
Maximum operating pressure | 0.7 MPa |
Minimum operating pressure
| Ø 4| 0.3 MPa
Ø 6| 0.2 MPa
Ø 10, Ø 16| 0.15 MPa
Proof pressure| 1 MPa
Ambient and fluid temperatures| -10 to 70 °C (No freezing)
Lubrication| Not required (Non-lube)
Piston speed| 50 to 500 mm/s
Cushion| None
Stroke length tolerance| +1.0
0
Rod end type| With thread/Without thread
Mounting| Panel mount type| Embedded type
Accessory (Standard equipment)
| ****
Standard equipment
| ****
Mounting nut (2) Rod end nut (2)*1
| Mounting nut (1)
Gasket (1) Rod end nut (2)*1
Option| Hose nipple (Excludes Ø 4)| —
- 1 When the rod end is threaded
- For details about the hose nipple (accessory), refer to page 8.
Pin Cylinder: Single Acting, Spring Return CJP Series
Weight
Bore size [mm] | Stroke [mm] |
---|---|
5 | 10 |
4 | 10 |
6 | 10.6 |
10 | 28 |
16 | 72 |
The weight of the hose nipple (4 g) for panel mounting is excluded.
Hose Nipple Dedicated for Panel Mount Type (With fi xed orifi ce)
Applicable tubing | Part no. |
---|---|
For Ø 4/Ø 2.5 tubing | CJ-5H-4 |
For Ø 6/Ø 4 tubing | CJ-5H-6 |
Theoretical Output
Bore size [mm] | Operating direction | Operating pressure [MPa] |
---|---|---|
0.3 | 0.5 | 0.7 |
4
| OUT| 0.97| 3.48| 6.00
IN| 1.0
6
| OUT| 4.56| 10.2| 15.9
IN| 1.42
10
| OUT| 17.6| 33.3| 49.0
IN| 2.45
16
| OUT| 44.5| 84.7| 124.9
IN| 5.04
Spring Reaction Force
Bore size [mm] | Stroke [mm] | Retracted side | Extended side |
---|---|---|---|
4 | 5, 10, 15 | 2.80 | 1.00 |
6 | 5, 10, 15 | 3.92 | 1.42 |
10 | 5, 10, 15 | 5.98 | 2.45 |
16 | 5, 10, 15 | 15.78 | 5.04 |
Allowable Kinetic Energy
Caution: When driving an inertial load, operate a cylinder with kinetic energy within the allowable value. The range in the chart below that is delineated by bold solid lines indicates the relation between load mass and maximum driving speeds.
Allowable Lateral Load
Strictly observe the limiting range of lateral load on a piston rod. (Refer
to the below graph.) If this product is used beyond the limits, it may shorten
the ma-chine’s life or cause damage.
Panel Mount Type
Embedded Type
Component Parts
No. | Description | Material | Note |
---|---|---|---|
1 | Tube | Brass | Electroless nickel plating |
2 | Piston | Stainless steel |
3
| ****
Collar
| Ø 4, Ø 6, Ø 10| Brass| Ø 4, Ø 6, Ø 10| Electroless nickel plating
Ø 16| Oil-impregnated sintered alloy| Ø 16| —
4| Return spring| Steel wire| Zinc chromating
5| Piston seal| NBR|
6
| ****
Mounting nut
| Ø 4| Brass| Electroless nickel plating
Ø 6, Ø 10, Ø 16| Steel| Zinc chromatin
7| Rod end nut| Steel| Zinc chromatin
8| Seal retainer| Stainless steel| Only applicable to Ø 6, Ø 10,
and Ø 16
9| Gasket| NBR| Embedded type only
Replacement Parts: Gasket
Bore size [mm] | Order no. | Contents |
---|---|---|
4 | CJPS4-G |
Above no. o
6| CJPS6-G
10| CJPS10-G
16| CJPS16-G
-
For the embedded type
-
Since gaskets (10 pcs./set) do not include a grease pack (10 g), order it separately.
Grease pack part number:- GR-S-010 (10 g)
Dimensions
Accessory Bracket Dimensions
Rod End Cap
Accessory
Related Products
Refer to the Catalogue on https://www.smc.eu.
Simple Specials
The following changes are dealt with through the Simple Specials System.
Change of Rod End Shape
Applicable Series
Series | Action | Symbol for change of rod end shape |
---|
CJP
| Standard type Single acting, Spring return| ****
CJP
| ****
Single acting (Spring return)
| ****
Ø 6 to Ø 16
XA0, XA1, XA10, XA11
Precautions
- SMC will make appropriate arrangements if no dimension, tolerance, or fi nish instructions are given in the diagram.
- Standard dimensions marked with “∗” will be as follows to the rod diameter (D). Enter any special dimension you require. Ø 6 to Ø 16 D – 1 mm
- Please contact SMC separately for the piston rod end pattern part numbers other than the table above.
- “A0” is the same shape as the standard type. (The specifications of A0 are that only dimensions A and H are changed from the standard type.)
Made to Order Common Specifications
Please contact SMC for detailed dimensions, specifications, and delivery times.
Pin Cylinder with Rod Quenched
The piston rod material is changed and the rod end is quenched.
Applicable Series
Series | Description | Model | Action | Note |
---|
CJP
| ****
Pin cylinder
| CJPB| Single-acting (Panel mount)| Excludes Ø 4
CJPS| Single-acting (Embedded)| Excludes Ø 4
How to Order
- Specifications: Same as the standard type
Construction
(Dimensions are the same as the standard type.)
- The shape and the dimension of the quenched part of the rod end are the same for both the panel mount type and the embedded type.
- The figure below shows the panel mount type.
CJPB
Fluororubber Seals
Applicable Series
Series | Description | Model | Action | Note |
---|---|---|---|---|
CJP | Pin cylinder | CJPB | Single-acting (Panel mount) | Excludes Ø 4 |
CJPS | Single-acting (Embedded) | Excludes Ø 4 |
How to Order
Specifications
Seal material | Fluororubber |
---|---|
Specifications other than the above and dimensions |
Same as the standard type
Specific Product Precautions
Piping
Caution
The following fi ttings are recommended for this cylinder connection.
However, there may be a case where the piston speed exceeds 500 mm/s even with
the recommended fi ttings for this cylinder. Use a speed controller in such
cases.
Please be aware that cylinder speed may slow down on the retracting side when using the above One-touch fittings and miniature fi ttings with a cylinder bore size of Ø 16.
Hose nipple
In addition to the above fittings and hose nipples, the below fi ttings can also be attached to the cylinder. When using the below fi ttings, be sure to provide a speed controller after adjusting it to 500 mm/s or less.
Recommended Speed Controller
- For details about One-touch fittings, miniature fittings, and speed controllers (applicable tubing O.D. Ø 2 only), refer to the Catalogue on https://www.smc.eu. Also, for details about speed controllers (applicable tubing O.D. Ø 3.2 to Ø 6), refer to the Catalogue on https://www.smc.eu.
- Refer to the Fittings and Tubing Precautions (Catalogue on https://www.smc.eu) for handling One-touch fittings.
Mounting
Caution: Do not use it in such a way that a load could be applied to the
piston rod during the retraction.
The spring that is built into the cylinder provides only enough force to
retract the piston rod. Thus, if a load is applied, the piston rod may not be
able to retract to the end of the stroke.
Safety Instructions
These safety instructions are intended to prevent hazardous situations and/or
equipment damage. These instructions indicate the level of potential hazard
with the labels of
“Caution,” “Warning” or “Danger.” They are all important notes for safety and
must be followed in addition to International Standards (ISO/IEC) 1), and
other safety regulations.
- Caution indicates a hazard with a low level of risk which, if not avoided, could result in minor or moderate injury.
- Warning indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury.
- Danger indicates a hazard with a high level of risk which, if not avoided, will result in death or serious injury.
ISO 4414 : Pneumatic fl uid power – General rules relating to systems.
ISO 4413: Hydraulic fl uid power – General rules relating to systems. IEC
60204-1: Safety of machinery – Electrical equipment of machines. (Part 1:
General requirements)
ISO 10218 -1: Manipulating industrial robots – Safety. etc.
Warning
-
The compatibility of the product is the responsibility of the person who designs the equipment or decides its specifi cations.
Since the product specifi ed here is used under various operating conditions, its compatibility with specifi c equipment must be decided by the person who designs the equipment or decides its specifi cations based on necessary analysis and test results. The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined its compatibility with the product. This person should also continuously review all specifi cations of the product referring to its latest catalog information, to give due consideration to any possibility of equipment failure when confi during the equipment. -
Only personnel with appropriate training should operate machinery and equipment.
The product specifi ed here may become unsafe if handled incorrectly. The assembly, operation, and maintenance of machines or equipment including our products must be performed by an operator who is appropriately trained and experienced. -
Do not service or attempt to remove product and machinery/equipment until safety is confi armed.
- The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or runaway of the driven objects have been completed.
- When the product is to be removed, confi rm that the safety measures as mentioned above are implemented and the power from any appropriate source is cut, and read and understand the specifi c product precautions of all relevant products carefully.
- Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
- Contact SMC beforehand and take special consideration of safety measures if the product is to be used in any of the following conditions.
- Conditions and environments outside of the given specifi cations, or use outdoors or in a place exposed to direct sunlight.
- Installation of equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military, medical treatment, combustion, and recreation, or equipment in contact with food and beverages, emergency stop circuits, clutch, and brake circuits in press applications, safety equipment or other applications unsuitable for the standard specifi cations described in the product catalog.
-
An application that could have negative effects on people, property, or animals requires special safety analysis.
-
Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective function, and periodical checks to confi rm proper operation.
Limited warranty and Disclaimer/ Compliance Requirements
The product used is subject to the following “Limited Warranty and Disclaimer”
and “Compliance Requirements”. Read and accept them before using the product.
Limited warranty and Disclaimer
- The warranty period of the product is 1 year in service or 1.5 years after the product is delivered, whichever is fi rst. 2) Also, the product may have specifi ed durability, running distance, or replacement parts. Please consult your nearest sales branch.
- For any failure or damage reported within the warranty period which is our responsibility, a replacement product or necessary parts will be provided. This limited warranty applies only to our product independently, and not to any other damage incurred due to the failure of the product.
- Before using SMC products, please read and understand the warranty terms and disclaimers noted in the specifi ed catalog for the particular products.
Vacuum pads are excluded from this 1 year warranty.
A vacuum pad is a consumable part, so it is warranted for a year after it is
delivered. Also, even within the warranty period, the wear of a product due to
the use of the vacuum pad or failure due to the deterioration of rubber
material is not covered by the limited warranty.
Compliance Requirements
- The use of SMC products with production equipment for the manufacture of weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
- The exports of SMC products or technology from one country to another are governed by the relevant security laws and regulations of the countries involved in the transaction. Before the shipment of an SMC product to another country, ensure that all local rules governing that export are known and followed.
Caution: SMC products are not intended for use as instruments for legal
metrology.
Measurement instruments that SMC manufactures or sells have not been qualifi ed
by type approval tests relevant to the metrology (measurement) laws of each
country.
Therefore, SMC products cannot be used for business or certain cations
ordained by the metrology (measurement) laws of each country.
FAQ
- Q: What is the maximum operating pressure of the Pin Cylinder?
- A: The maximum operating pressure is 0.7 MPa.
- Q: Can the Pin Cylinder be used for high-frequency operations?
- A: Yes, the cylinder can operate at a piston speed of 50 to 500 mm/s.
- Q: Is lubrication required for the Pin Cylinder?
- A: No, lubrication is not required as it is a non-lube cylinder.
- Q: What are the available rod end cap options?
- A: The available options are rod end cap (flat type) and rod end cap (round type).
SMC Corporation (Europe)
Austria| +43 (0)2262622800| www.smc.at|
office@smc.at| Lithuania **
+370 5 2308118 www.smclt.lt|
info@smclt.lt
---|---|---|---|---|---
Belgium| +32 (0)33551464| www.smc.be|
info@smc.be| Netherlands +31 (0)205318888
www.smc.nl| info@smc.nl
Bulgaria| +359 (0)2807670| www.smc.bg|
office@smc.bg| Norway **
+47 67129020 www.smc-norge.no| post@smc-
norge.no
Croatia| +385 (0)13707288| www.smc.hr|
office@smc.hr| Poland **
+48 222119600 www.smc.pl|
office@smc.pl
Czech Republic| +420 541424611| www.smc.cz|
office@smc.cz| Portugal **
+351 214724500 www.smc.eu|
apoioclientept@smc.smces.es
Denmark| +45 70252900| www.smcdk.com|
smc@smcdk.com| Romania ** +40 213205111
www.smcromania.ro|
smcromania@smcromania.ro
Estonia| +372 6510370|
www.smcpneumatics.ee|
smc@info@smcee.ee| Russia ** +7
(812)3036600 www.smc.eu|
sales@smcru.com
Finland| +358 207513513| www.smc.fi|
smcfi@smc.fi| Slovakia ** +421 (0)413213212
www.smc.sk|
office@smc.sk
France| +33 (0)164761000| www.smc-france.fr| info@smc-france.fr| Slovenia
** +386 (0)73885412 www.smc.si|
office@smc.si
Germany| +49 (0)61034020| www.smc.de|
info@smc.de| Spain ** +34 945184100
www.smc.eu|
post@smc.smces.es
Greece| +30 210 2717265| www.smchellas.gr|
sales@smchellas.gr| Sweden ** +46
(0)86031240 www.smc.nu|
smc@smc.nu
Hungary| +36 23513000| www.smc.hu|
office@smc.hu| Switzerland
+41 (0)523963131 www.smc.ch|
info@smc.ch
Ireland| +353 (0)14039000|
www.smcautomation.ie|
sales@smcautomation.ie| Turkey ** +90
212 489 0 440 www.smcpnomatik.com.tr|
info@smcpnomatik.com.tr
Italy| +39 03990691| www.smcitalia.it|
mailbox@smcitalia.it| UK ** +44 (0)845
121 5122 www.smc.uk| sales@smc.uk
Latvia| +371 67817700| www.smc.lv|
info@smc.lv| |
| South Africa +27 10 900 1233
www.smcza.co.za
zasales@smcza.co.za
Printing BW 00 Printed in Spain
Specifications are subject to change without prior notice and any obligation
on the part of the manufacturer
References
- France.fr : Explore France and its wonders - Explore France
- Frontpage | Norge.no
- Automatización neumática y eléctrica | SMC España
- Automatisation des systèmes industriels | SMC France
- SMC Norway
- Industrielle Automation | SMC Austria
- SMC | SMC België
- SMC Bulgaria Expertise - Passion - Automation | SMC Bulgaria
- SMC | SMC Schweiz
- SMC CZ | SMC CZ
- Industrielle Automatisierungstechnik | SMC Deutschland
- SMC Europe | SMC Europe
- SMC | SMC Hrvatska
- Automatizálási megoldások és szolgáltatások | SMC Hungary
- SMC Latvia | SMC Latvia
- Pneumatische & Elektrische Automatisering | SMC Nederland
- Industriell automation | SMC Automation AB Sverige
- Automatyzacja Procesów Przemysłowych • Przemysł 4.0 | SMC Polska
- SMC | SMC Slovenia
- Automation Solutions & Services | SMC Pneumatics UK
- SMC | SMC Ireland
- Industriel automationsløsninger | SMC Danmark
- SMC Italia Hellas Branch | SMC Greece
- Componenti e soluzioni per l'automazione industriale | SMC Italia
- SMC Automation Estonia | SMC Estonia
- SMC | SMC Türkiye
- SMC Romania
- SMC | SMC South Africa
- SMC Europe | SMC Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>