Sunco SHG-40W 4FT LED Grow Light for Indoor Plants User Manual
- June 17, 2024
- SUNCO
Table of Contents
Sunco SHG-40W 4FT LED Grow Light for Indoor Plants
Dimensions
- Width: 5.3 inches
- Length: 47.2 inches
- Height: 2 inches
Specifications
- Voltage: [insert voltage]
- Wattage : 40W
- Power Factor : [insert power factor]
- Beam Angle : [insert beam angle]
- PPF (Photosynthetic Photon Flux): [insert PPF]
- PAR (Photosynthetically Active Radiation): [insert PAR]
- Dimmable: [insert dimmable information]
- 5 ft. Length: [insert length]
- Average Lifetime: [insert average lifetime]
- Full Spectrum: [insert full spectrum information]
- Moisture Rating: [insert moisture rating]
- CRI (Color Rendering Index): [insert CRI]
- Usage Frequency: [insert usage frequency]
- Warranty: [insert warranty information]
Whats in the Box
Grow Light
Safety Information
To reduce the risk of fire, electric shock, or physical injury:
- Turn off the power before changing the fixture.
- Suitable for use in damp environments at temperatures ranging from 4°F to 113°F. Not for use where directly exposed to water.
- Not intended for use with emergency fixtures.
- Not compatible with photo controls.
- Not compatible with occupancy sensors.
- Not compatible with dimmers.
- Not compatible with timing devices.
- All electrical connections must be by local and National Electric Code (N.E.C.) standards.
- Please review the installation manual carefully before proceeding. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections. WARNING:
FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation. Please review all instructions carefully before installation.
Installation
Installation Guide – Suspension Mount
-
STEP 1
- a. Turn off the circuit breaker before installation.
- b. Surface must support fixture weight.
Plasterboard: Requires 3/8” thickness. Use #8 eye hook screws with anchors or expansion bolts (not included).
-
STEP 2
- a. Drill pilot holes 46.5 inches apart.
- b. Insert two plastic anchors, then screw each eye hook into an anchor.
-
STEP 3
- a. Depending on your lighting plan, space any additional anchors accordingly.
- b. Link up to 4 shop lights together
-
STEP 4
- a. Insert a hook chain into each slot of the light fixture. Repeat for each slot (there should be 4 total).
- b. Use pliers to crimp ends and secure as needed.
-
STEP 5
- a. Attach loose ends of each chain onto corresponding eye hooks on the ceiling.
-
STEP 6
- a. Plug the power cord into an electrical outlet. Turn on the circuit breaker and test the light.
- b. Distance between lamp and plant surface should be between 11.81 and 23.62 inches.
-
STEP 7
- a. Turn off the circuit breaker before installation.
- b. Surface must support fixture weight.
Plasterboard: Requires 3/8” thickness.
-
STEP 8
- a. Install 2 plastic anchors 3.25 inches apart, repeat this step for an additional pair of plastic anchors 46” inches away from the initial pair of plastic anchors. Insert a screw into each anchor.
- b. Plastic anchor and screw positions should match mounting holes on the back side of the light fixture. The gap between the screw cap and the ceiling should be 0.33 inches.
-
STEP 9
- a. Depending on your lighting plan, space any additional anchors accordingly.
- b. Link up to 4 shop lights together
-
STEP 10
- a. Lift the fixture to the screws and slide it to one side to secure it into place. The fixture should be firmly fixed against screws.
-
STEP 11
- a. Distance between lamp and plant surface should be between 11.81 and 23.62 inches.
-
STEP 12
- a. Plug the power cord into an electrical outlet.
- b. Turn on the circuit breaker and test the light.
Product Details
Dimensions
Specifications
Light Distribution Angle
Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles: A symmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a certain degree in up-lighting. An asymmetric lighting distribution angle, also known as a beam angle, creates a pattern that focuses light in a specific direction.
This type of lighting is ideal for task lighting as it reduces glare and light spill in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more. It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.
Customer Support
Warranty Policy
This product is covered by our industry-leading 3-year warranty.
It gets even better – scan the QR code for 2 extra years of protection!
30 Day Return Policy
- At Sunco, we value our customers and stand by the quality and performance of our products.
- If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.
FAQ
- Q: Is this product dimmable?
- A: [Insert answer here]
- Q: What is the average lifetime of this product?
- A: [Insert average lifetime information here]
- Q: Can I link multiple lights together?
- A: Yes, you can link up to 4 shop lights together.
Customer Service
Our Los Angeles team of lighting experts is here to assist you with all your
needs! Contact us at:
- Email: [email protected]
- Call or Text: 844-334-9938