Strong SRT 24HE4023C 24 Inch 60cm HD TV User Manual

Strong SRT 24HE4023C 24 Inch 60cm HD TV User Manual

INSTRUCTION

SAFETY INSTRUCTIONS

• Read all of the instructions before operating the set. Keep these instructions well for later use.
• Only use attachments/accessories specied or provided by the manufacturer (such as the exclusive supply adapter, battery etc.).
• Please refer to the information on the exterior back enclosure for electrical and safety information before installing or operating the apparatus.
• To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture.
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspaper, table-cloths, curtains, etc.
• The apparatus shall not be exposed to dripping or splashing and no objects
• lled with liquids, such as vases, shall be placed on the apparatus.
• The mark indicates a risk of electric shock. The external wires must be installed by an instructed person or ready-made leads or cords must be used.
• To prevent injury, this apparatus must be securely attached to the oor/wall in accordance with the installation instructions.
• Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent types.
• The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, re or the like.
• Excessive sound pressure from earphones and headphones can cause hearing  loss. Listening to music at high volume levels and for extended durations can damage one’s hearing.
• In order to reduce the risk of damage to hearing, one should lower the volume to a safe, comfortable level, and reduce the amount of time listening at high levels.
• The mains plug or appliance coupler is used as disconnect device, it shall remain readily operable. When not in use and during movement, please take care of the power cord set, e.g. tie up the power cord set with cable tie or something like that. It shall be free from sharp edges or similar which can cause abrasion of the power cord set. When put into use again, please make sure the power cord is not damaged. In case of damages, please get the power cord replaced by a similar one with the same speci
• cations. The absence of a light indication on the apparatus does not mean that it is fully disconnected from the mains. To disconnect the apparatus completely, the mains plug must be pulled out.
• Attention should be drawn to environmental aspects of battery disposal.
• No naked ame sources, such as lighted candles, should be placed on the apparatus.
• To prevent the spread of re, keep candles or other open ames away from this product at all times.
• A USB terminal can provide a maximum of 500 mA.
• Equipment with this symbol is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. Operating Environment
• Do not install this equipment in a conned space such as a bookcase or similar unit.
• Do not use the set near damp, and cold areas, protect the set from overheating.
• Keep away from direct sunlight.
• Do not use the set near dust place.
• Do not attach candle to accessible opening area, to avoid ammable foreign material from entering the TV.
  
  

WEEE Directive
Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human  health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return  your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

STORAGE
Your device has been carefully checked and packed before shipping. When unpacking it, make sure that all the parts are included and keep the packaging away from children. We recommend that you keep the carton during the warranty period, to keep your device perfectly protected in the event of repair or warranty.

ACCESSORIES

• 1x installation instructions
• 1x safety instructions/warranty cards
• 2 x Feet standards including screws
• 1x remote control
• 2x AAA batteries
• 1 x Power adaptor 12Volt-4Amp
• 1 x Main power wire 230V
• 1 x Cigarette car adaptor 12Volt

EQUIPMENT SET-UP

Install the display on a solid horizontal surface such as a table or desk. For ventilation, leave a space of at least 10 cm free all around the set. To prevent any fault and unsafe situations, please do not place any objects on top of the set. This apparatus can be used in tropical and/or moderate climates.

Stand assembly instruction

1. Carefully place the TV with its front side facing down on a cushioned at surface in order to protect the TV and the TV screen from damage.
2. Take out the 2x feet and assemble them to the TV.
3. Fasten the feet to the bottom of the TV using the 4xPA4x14mm screws.
   

NOTE: Clean the screen with a soft, dry cloth after switching o and unplugging the television and avoid glass sprays and other household cleaning agents.

This user manual provides complete instructions for installing and using this TV. The symbols serve as follows.
WARNING: Indicates warning information.
NOTE: Indicates any other additional important or helpful information.
MENU : Represents a button on the remote control or the TV. Move to Represents a menu item within a window.

INSTALLATION

NOTE: The graphics are for representation only.

1. Power indicator /remote sensor
2. Speakers
3. Button: Input source, Standby/ON.
   

REAR PANEL
NOTE : The graphics are for representation only.

1. DC IN Power entree to connect included 230V -12volt main adaptor or 12Volt car adaptor.
2. /PDIF (optical) Use an optical cable to connect your TV to a compatible digital amplier or Home theatre set.
3. HDMI 2 (CEC) Connect HDMI input signal from a signal source such as DVD, Blu-ray player or game console.
4. HDMI 1 (ARC/CEC) Connect HDMI input signal from a signal source such as Chromecast stick, Android box, Google TV box or Dolby audio amplier.
5.  ANT 1 Connect a coaxial cable to receive signal from the DVB-T/T2 antenna or DVB-C cable.
6. ANT 2/ SAT IN Connect a coaxial cable to receive signal from the Dish LNB.
7. USB Connect a USB device for playback of multimedia les
8. HEADPHONE Headphone or Earphone audio output, speakers will be muted when earphone is plugged in.
9. COMMON INTERFACE Insert a Conditional Access Module (CAM) for decoding channels.
10. Mini AV IN To connect your video camera or other device using 3.5 mm AV cable to your TV to play videos on your TV screen.

REMOTE CONTROL

1. q Press to turn the TV on or standby.
2. ! Press to mute or restore the volume.
3. 0 ~ 9 Choose channel directly.
4. Press to access the TV sources.
5. INFO Display information about the current source.
6. DMP Access directly multimedia menu
7. EPG Press to display the current EPG information in DTV mode.
8. pqt u Navigate the menu.
9. ENTER Conrm the selection.
10. MENU Open the menu options. Step back in some menu options.
11. EXIT Exit the current menu.
12. VOL +/- Adjust the volume up or down.
13. LIST Press to view your assigned favourite list or main list channels. Press pq to cycle through your assigned favourite channels, press ENTER to conrm.
14. CH +/- Change programmes up or down. Big steps in Channel list.
15. Open or close Favourite List menu
16. SLEEP Select the sleep time, such as 15 min, 30 min etc.
17. INDEX Index or Transponder list
18. Recall between the last viewed channel or item
19. RED / 5 Press to fast reverse.
20. GREEN / 6 Press to fast forward.
21. YELLOW / 7 Press to play the previous le.
22. BLUE / 8 Press to play the next le.
23. / 12 Tele text On/O. Multimedia to start/pause playback.
24. / 3 Freeze picture or to stop playback.
25. SUBTITLE / Enable/disable subtitles in DTV mode
26. / Press to select screen formats or zoom function
27. 27. / HIDE Hide text in teletext mode
28. RADIO Switch between TV and Radio.
29. / AUDIO Audio Languages selection
30. No function

INSTALLING THE BATTERIES

Place 2x AAA batteries in the battery compartment of the remote control. Make sure to match the polarity markings inside the compartment.
NOTE: Pictures are only for reference. Actual items may dier.

1. Open the cover.
2. Put 2x AAA batteries in the compartment and make sure the polarity is correct.
3. Close the cover.

Precautions for using the batteries
Improper using of the battery will cause leakage. Carefully follow these instructions.

1. Please note the batteries’ polarity to avoid short circuit.
2. When the battery’s voltage is insucient which aect the use range, you should replace it with a new battery. Remove the batteries from the remote control unit if you do not intend to use it for a long time.
3. Do not use dierent types of batteries (for example Manganese and Alkaline batteries) together.
4. Do not put the battery into re, and charge or decompose the battery.
5. Please dispose batteries abide by relevant environmental protection  regulation.

USING THE REMOTE CONTROL

•  Use the remote control by pointing it towards the remote sensor. Items between the remote control and the remote sensor could block normal operation.
• Do not cause the remote control to vibrate violently. Also, do not splash liquid on the remote control, also do not put the remote control in a high humidity place.
• Do not place the remote control under direct sunlight which will cause deformation of the unit by heat.
• When the remote sensor is under direct sunlight or strong lighting, the remote control will not work. If so, please change the lighting or TV’s position, or operate the remote control closer to the remote sensor.

FIRST TIME INSTALLATION
After all connections have been properly made, switch on your TV. The welcome wizard appears on screen and conrm with OK to start the installation. The language selection will appear on screen. Use pq to select the OSD Language of your preference. Press u and then use pq to select the country where you will use this TV. This is important to set setting as text character correctly.

Press u to change Environment from Home to Shop modus to demonstration TV in shop, otherwise keep as it is. Press u and then use pq to select the Antenna / Tuner type you are using for reception. Press u for next step to go to Tuning setup. If you like to make change, use u to go step back in this wizard.

In Antenna Type selection you select which tuner input source you like to use.
Air to receive terrestrial broadcasts with indoor or outdoor antenna.
Cable to receive cable broadcasts if you have cable connection.
Satellite to receive satellite broadcasts if you are equipped with a satellite dish. Next step is depending of your choice in Tuner setup

AIR > DVB-T/T2 I NSTALLATION
Directly when you select Air and press u button. Auto channel searching for channels is started. Just wait until all channels are found. Now you can enjoy digital Tv.

If no channels are found, check antenna connection, or check if arial is correct adjusted to transmission tower. Start from beginning the installation trough menu/ option/ Installation Guide.

CABLE > DVB-C INSTALLATION
After you select Cable and press u button. The Cable Scan Menu will open. In this menu you can select Full for automatically searching for channels if you do not know the details of you local provider. Select Network Search to install the channels list in sorted channel order from local provider.
Cable Setting Press pq t u to highlight your settings. Scan type You can select Network Search or Full.
Network ID The default setting is Auto. To enter your own value press t u and enter  (with 0 ~ 9) the used Network ID from your provider. Frequency The default setting is Auto. To enter your own value press t u and enter (with 0 ~ 9) the main frequency used by your provider in KHz.
Symbol Rate The default setting is Auto. To enter your own value press t u and enter (with 0 ~ 9) the used Symbol Rate from your provider. (Ks/s) most used values are 6900 or 6875. After selection is made, press ENTER Auto channel searching for channels is now started. Just wait until all channels are found.

Now you can enjoy digital Tv.
If no channels are found, check antenna connection, or check if correct values of network are entered. Start from beginning the installation trough menu/ option/ Installation Guide.

NOTE: Please, check the settings for your cable system used by your provider! Full scan will have a duration of approximately 20 minutes, depending on your cable network.

SATELLITE > DVB-S/S2 INSTALLATION
Select Satellite press u button to proceed installation for channels from satellite.
If you have selected country Germany or Austria , then Channel Preset menu will open. Select if you like load a pre-installed channel list ready to use or proceed with Auto Channel search as for all other countries.

Select Auto Channel Search to open Satellite Setup menu. Use pq to highlight the satellite your dish is aimed at and conrm with ENTER button. use u to highlight the options of you dish antenna installation.
Select LNB type to select your used LNB type in the dish antenna. (Most common is 09750/10600).

Select DiSEqC 1.0 or 1.1 if your installation is using switch for selection of more satellite dishes.

(Most common is to set DiSEqC 1.0 to LNB 1 port).

Select Motor for the satellite specialist how are using motor to receive multiple satellites.

If all setting and selection are made, press BLUE Scan button to open next menu Channel Search.

Scan Mode Choose between Default (recommended) and Blind Scan
Encrypted type Select FTA channels to search Free-To-Air channels only.
Select Encrypted to search scrambled /coded channels only.
Select All to search all channels.

Service Type Select All to search Digital TV channels and Radio.
Select DTV for only Digital TV channels.
Select RADIO to search radio channels only.

It is recommended to use the default settings.

conrm with ENTER button to start auto searching of channels. Just wait until all channels are found. Now you can enjoy digital Tv. If no channels are found, check antenna connection, or check if correct values of network are entered. Start from beginning the installation trough menu/ option/ Installation Guide.

ELECTRONIC PROGRAMME GUIDE (EPG)

EPG stands for Digital Electronic Programme Guide. It is supplied by the programme providers and oers information on
broadcasted programmes. You can access it in digital mode by pressing EPG on the remote control. Press EPG to bring up the EPG interface. Use pq to select a channel. Press INDEX u to switch to overview from one channel EPG. Use pq to select event where you like to know more details. Press EXIT to stop and return to viewing modes.

Then press the COLOUR BUTTONS for entering the required settings.
GREEN Information YELLOW Schedule List BLUE Set a reminded to event or set even Timer function.

MENU SETTINGS
Below items depend if they are available of select input source. Use SOURCE to select other source. Selections are DTV, ATV, HDMI, AV, and USB Media.

MENU CONTROL (DTV MODE)
Press MENU to enter the main menu. Press t u to select an item. Press ENTER to select the submenus. Press MENU to exit the
item.

CHANNEL
Press MENU to display the main menu. Press ENTER to select Channel in the main menu. Press pq to select the option you wish to adjust in the Channel menu.
Press ENTER to enter sub menu. After nish your adjustment, press MENU to save and return to the previous menu. Below items depend if they are available of select input source. Use SOURCE to select other source.

ANTENNA TYPE
Press ENTER to select which antenna type you want to use. Select between, Air, Cable or Satellite.

AUTO TUNING
Press pq to select Auto Tuning. If the TV use DVB-T or DVB-C tuner please refer to chapters 3.1 and 3.2; for Satellite (DVB-S) tuner please refer to chapter 3.3.

DISH SETUP
If you use Satellite as input source, the Dish Setup menu allow you to set you satellite and belonging settings as DiSEqC port and LNB type. Afterwards you may start the Auto Tuning with the BLUE Scan button or Manual Tuning by selecting with INDEX button the wanted transponder.

DTV MANUAL TUNING (IN DVB-T MODE ONLY)
Search and store programmes manually. Press pq to select DTV Manual Tuning. Then press ENTER to enter the sub-menu. Press t u to select a Channel No., and then press ENTER to start the search. The search stops when a programme is found and this programme will be stored in the current channel position. Press MENU to exit.

ATV MANUAL TUNING (IN DVB-C MODE ONLY)

In the Channel menu, select ATV Manual Tuning and press ENTER to access. Highlight and press pq to select Storage To 1 (maybe other number), Sound System and Channel No.. Then select search and press ENTER to start the search. Press u for the unit to search towards higher frequency. Press t for the unit to search towards lower frequency. The search stops when a programme is found and this programme will be stored in the current channel position. If you want  to stop the search, press MENU. Sound Standard Select the Sound standard. 11 Video Standard Select the Video standard (Available: A

0 MEDIA

1. Some USB storage devices may not be compatible to operate smoothly with this TV.
2. Back up all of the data in the USB storage device in case data is lost due to an unexpected accident. STRONG does not assume any liability for the losses by misuse or malfunction. Data backup is consumer’s responsibility.
3. For large le sizes, the loading speed may be slightly longer.
4. The recognition speed of a USB storage device may depend on each device.
5. When connecting or disconnecting the USB storage device, make sure the TV isnot in USB mode otherwise the USB storage device or the les stored in it may be damaged.
6. Please use only a USB storage device which is formatted in FAT32, NTFS (playback only) le system provided with the Windows operating system. In case of a storage device formatted as a dierent utility programme which is not supported by Windows, it may not be recognized.
7. For Software Updates and Database functions it is recommended to use USB Sticks (keys) in FAT32.
8. When using a USB Hard Disk Drive which is not powered independently, ensure its power does not exceed 500 mA. Otherwise the TV system will change into standby mode, and you must pull out the USB Hard Disk and restart the TV system.
9. An “Unsupported File” message will be displayed if the le format is unsupported or the le is corrupted.
10. FHD big picture needs longer time to process, which is not caused by the TV. Please be patient.
11.  This TV may not support some multimedia les changed and upgraded asthe change of the encoding format or other technical aspects advances.
12.  Please refer to chapter 9. Appendix for a list of supported le formats for USB playback.
    

USB MENU
Press SOURCE and select Media or press DMP button.. You can view movie, music, photo and text les from your USB storage devices. Connect a USB storage device to the USB input terminal and select the types of media on the home page: Movie, Music, Photo and text. Press ENTER, the screen will show the connected USB device, press ENTER again to view the le folders and les. Press pq or t u to select a folder, press ENTER to open the folder and select the les. Highlight the one you want to play or watch or press directly u 2 to start playing directly. Press 3 to stop playing and return to upper lever folder. Continuously press EXIT to go back to upper level folder. Repeat again to select and play another media type.

NOTE: By choosing one of the three media types, for example Movie, the folders inside will display only video les and no other formats.

SOFTWARE UPDATE VIA USB
From time to time you can check if there is an improved software version available. This can be viewed and downloaded from our website www.strong- eu.com. Search the model number on our website’s service support section. If there is an improved software version you can download the le and copy it to the root of a USB device. Then press pq button to select Software Update (USB) from the Option menu on your TV. Plug your USB device into the USB slot and press ENTER to update the respective software. Conrm with Yes using t u. When the update is completed, remove the USB stick, disconnect your device from the main power  supply and plug in again.

TROUBLESHOOTING
There maybe various reasons for abnormal operation of your TV set. Check your TV set according to the general procedures shown below. Additionally, we strongly recommend reading the detailed troubleshooting of your TV set in the full user manual available on our website www.strong-eu.com. If your TV set does not work properly after checking the general and detailed troubleshooting, please contact your dealer, the local Service Hotline, or send an email  to our support via www.strong-eu.com. DO NOT try to open or disassemble your TV set. It may cause a dangerous situation and the warranty will be void.

connector is completely plugged at the TV and into power socket.2.       Make sure that the switch on multipoint connectors is switched ON as well.3. The electrical outlet may be damaged.4.       STBY LED is defective.
No Signal| 1.       The TV is not connected to a signal source (DVB-C, DVB-S/S2 or DVB-T/T2) or the antenna (terrestrial or satellite antenna) is maybe not aligned correctly respectively the according connection and distribution equipment might show malfunction, incompatibility or defectives.2.       DVB-T/T2: Active antennas need antenna power switched ON or external power connected. Antenna is maybe out of digital signal reception in your area. Check reference from service providers about coverage.3. DVB-S/S2: Incorrect values of some tuner parameters (e.g. one or some channel(s) changed to another transponder or are no longer emitted). Incorrect values of LNB parameters.
The picture and sound remain frozen, or macro blocks or similar distortion are visible on the screen.| DVB-S/S2,DVB-T/T2: The reception signal is too weak or disturbed by electromagnetic, high-frequency, or other interference signals. DVB-T/T2 : Disturbances caused by signal reflections.DVB-C, DVB-S/S2: The connection cables at the signal source are too long (too high attenuation). DVB-T/T2, DVB-S/S2: The antenna is not properly adjusted or got misaligned after storm etc.
Any other reception or signal related problems| 1.       Generally cables might have loosened. Moisture might have entered into cables or connectors. There is heavy rain or heavy storm at present (DVB-S/S2 and -T/T2). Check the cable connections. DVB-S/S2 and -T/T2: Check all equipment connected between the reception point and the TV.2.       Wait until heavy rain/thunderstorm passed. If no solution ask a local satellite specialist for advice. DVB-S/S2: The satellite dish is NOT aligned to the (correct) satellite(s). Ask a local satellite specialist for advice.3.       DVB-S/S2: Satellite dish is too small. Trees or buildings are in path. Ask a local satellite specialist for advice.4.       DVB-S/S2: Signal is too strong, maybe need to be atennuated. Ask a local satellite specialist for advice.
No colour| 1.       Devices are not properly connected (scart, RCA sockets) or wrong/bad cables are used.2.       Adjust the saturation.3.       Switch TV on another channel. It is possible that the current programme is broadcast in black and white.
No picture, normal sound| 1.       Adjust the brightness and contrast2. Radio channel is tuned to or the programme is not transmitting Video signals or another broadcasing interference/failure.
Normal picture, no sound| 1.       Press the volume up button to increase the volume level.2.       Audio is muted, press ❾ to restore the sound.3.       If external devices are used to loop the sound through, make sure to select correct sources and correct sound mode, for details also check advices in User Manuals from connected devices4.       Maybe a channel w/o audio is tuned to (demo) or the programme is not transmitting audio signals or there is some other transmission interference/failure.
Problem| Possible cause and solution
---|---
Playback of video is causing picturefreeze/macro blocks or similar distortion, especially on HD content.| Read/write speed of your USB device could be too low. Make sure to use a USB storage device with sufficient speed and space. Pen drives (USB sticks) may not support sufficient speed.
The remote control does not work| 1.       hange the batteries. If you’re using rechargable ones take care to use such with low self- discharge2. The batteries are not installed correctly or the types have been mixed3. IR Sensor is blocked or maybe interfered from bright light
The TV switches off after a certain time| Switch ON the TV and check settings for automatic STBY function, by default the TV switches OFF after 4 hours to fulfil European low power regulations and help you to save energy.

SPECIFICATIONS

Audio
Audio Output: 2 W Video
DVB-T: Reception range: VHF (174MHz ~ 230MHz), UHF (474MHz ~ 862MHz)
Input impedance: 75Ω
Channel Bandwidth: 7MHz/8MHz
Modulation: DVB-T: COFDM 2K/8K QPSK,16QAM,64QAM
DVB-S/S2 : QPSK ,8PSK
DVB-T2 : QPSK,16QAM,64QAM,256QAM
DVB-C : 16QAM, 32QAM, 64QAM, 128QAM, 256QAM
Video System: MPEG-2 MP@ML, MPEG-2 MP@HL, H.2 Main/Main- 10 prole, @L4.1, Support 8-bit/10-bit colordepth, 1920×1080@60fps
Sound System : MPEG-1 layer 1/2
System: DTV: DVB-T2, DVB-S2, DVB-C, DVB-T, DVB-S
ATV: PAL/SECAM/ NTSC
AV: PAL, NTSC

Connectors
1x ANT IN
1x SAT IN
2x HDMI
1x USB
1x S/PDIF (optical)
1x AV IN
1x COMMONINTERFACE (CI)
1x Headphones
1 x 12Volt DC IN
General Data
Power adaptor voltage: 180 ~ 240 V AC 50/60 Hz
Operating voltage: 12Volt / 4Ampere max.
Power consumption: 21Watt / 50Watt max.
Operating temperature: 5 °C ~ +35 °C
S torage temperature: -15 °C ~ +45 °C
Operating humidity: 0% ~ 89% RH, non-condensing
Storage humidity: 0% ~ 85% RH, non-condensing
Dimensions (WxHxD) in mm: 552.9 x 147.8 x 369
Net-weight: 2.5 kg

References

• Register a .EU.COM domain today!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>