RG Racing RAD0308PRO Ducati Streetfighter Radiator Guard Instruction Manual

RG Racing RAD0308PRO Ducati Streetfighter Radiator Guard

Product Information

The RAD0308PRO kit includes an upper radiator guard, a lower radiator guard, and rubber bungs. It is designed to provide protection to the radiator of your bike. Please ensure all parts are present before proceeding with the installation.

Specifications :

• Upper Radiator Guard: RAD0308PRO
• Lower Radiator Guard : RAD0308PRO
• Rubber Bung Quantity: 10

Tools Required:
General Torque Settings:

• M4 Bolt: 8Nm
• M5 Bolt: 12Nm
• M6 Bolt: 15Nm
• M8 Bolt: 20Nm
• M10 Bolt: 40Nm
• M12 Bolt: 40Nm

Fitting Instructions:

1. Place the upper radiator guard between the plastic shroud and radiator.
2. Insert the original bolts back through the two mounting holes where the plastic panel was removed from.
3. Repeat the same process for the lower radiator guard.

FAQ:

• Q: Can I use different bolts than the specified torque settings?
  A: It is recommended to use the specified torque settings to ensure proper installation and functionality of the radiator guards.

• Q: What should I do if I have missing parts in my kit?
  A: If any parts are missing, please contact our customer support for assistance in obtaining the missing components.

FITTING INSTRUCTIONS FOR RAD0308PRO

• THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE.
• SOME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY.
• DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
• PLEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING.
• IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
• PLEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF MOUNTING TO THE BIKE.
• IN THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS,
• THESE RUBBER WASHERS CAN BE THROWN AWAY.
• DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
  • WWW.RG-RACING.COM
• R&G Racing
• Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
• Tel: +44 (0)1420 89007
• Fax: +44 (0)1420 87301
• www.rg-racing.com
• Email: info@rg-racing.com

TOOLS REQUIRED

• SET OF ALLEN KEYS
• WIRE CUTTERS

GENERAL TORQUE SETTINGS

• M4 BOLT = 8Nm
• M5 BOLT = 12Nm
• M6 BOLT = 15Nm
• M8 BOLT = 20Nm
• M10 BOLT = 40Nm
• M12 BOLT = 40Nm

LEGEND

FITTING DIAGRAM

FRONT OF RAD GUARD

FITTING INSTRUCTIONS

• To fit R&G radiator guard to the bike, insert the 7x rubber grommets into the radiator guards in the holes circled in green in the Fitting Diagrams above.
• Remove the bolts and plastic panel circled in red in Picture 3.

Upper Rad Guard Fitment:
Offer the R&G Radiator Guard into position, wedging the top tab (circled yellow in Picture 2) between the plastic shroud and radiator, then insert the original bolts back through the two mounting holes where the plastic panel was removed from.

Lower Rad Guard Fitment:
Offer the R&G Radiator Guard into position, wedging the bottom tab (circled in yellow in Picture 3) between the plastic shroud and radiator, then insert the original bolts back through the two mounting holes.

ISSUE 1 – 02/01/2024 (TB)

CONSUMER NOTICE

• The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
• R &G RACING RETURNS POLICY (NON-FAULTY GOODS)
  • Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.

References

• RACING.COM - YOUR RACING CONNECTION
• Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors
• Welcome to R&G | Setting the standard in bolt-on motorcycle accessories and Crash Protectors

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>