Sunco P-PKG1WB-WH 6 Ultra Slim Downlight User Manual

Sunco P-PKG1WB-WH 6 Ultra Slim Downlight

Product Information

Specifications

• Voltage: Standard Voltage
• Wattage: Varies by model
• Frequency: Standard Frequency
• Beam Angle: Wide angle for optimal lighting
• Weight: Lightweight
• Housing Material: Plastic
• Dimmable: Compatible with recommended dimmers
• Model: Various models available
• Average Lifetime: Long-lasting
• Temperature: Suitable for various environments
• Moisture Rating: Moisture-resistant
• CRI: High Color Rendering Index for accurate color representation
• Usage: Suitable for indoor use
• IC Rated: IC rated for direct contact with insulation
• Warranty: Warranty information available

Product Usage Instructions

Before You Start

Safety Information: To ensure safety during installation, follow these guidelines:

• Turn off the circuit breaker before starting installation.
• Use the provided template to cut the hole in the ceiling.
• Review all instructions carefully before proceeding.

Quickstart Guide

1. Step 1: Use the template to cut the hole in the ceiling.
2. Step 2: Connect supply and junction wires as instructed.
3. Step 3: Attach the fixture to the junction box.
4. Step 4: Insert the fixture into the ceiling.

Installation Guide

Step 1

1. Turn off the circuit breaker before installation.
2. Cut out the housing size on the Installation Template and tape it onto the ceiling in the desired location.
3. Cut the ceiling hole using the Installation Template as a guide.

Step 2

1. Open the junction box and remove the appropriate knockout.

Whats in the Box?

Slim Downlight

Get Your Gear

Before You Start

Safety Information

To reduce the risk of fire, electric shock, or physical injury:

• Turn off circuit breaker before installing this fixture.• This product should be installed by a person familiar with the construction and operation of the product the hazards involved. Safety eyeglasses and gloves are recommended.
• Abide by related regional and local laws or regulations.
• Proper grounding is required to ensure safety.
• Do not alter, relocate, or remove wiring during installation.
• Do not make or alter any open holes in wiring enclosure or electrical components during installation.
• Check for shipping damage before installing. If the product is damaged, do not use it.
• Keep fixture away from corrosive substances.
• Suitable for damp locations at temperature ranging from 4°F to 113°F. Not for use where directly exposed to water.
• Clean the fixture regularly to ensure proper operation. Do not clean with harsh solvents.
• Use safety precautions and abide by regional and local laws or regulations.
• This product is not compatible with 3rd party sensors.
• This product is not compatible with photo controls.
• This product is not compatible with occupancy sensors.
• This product is not compatible with timing devices.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1.) This device may not cause harmful interference.

WARNING:

Cancer & Reproductive Harm- www.P65Warnings.ca.gov

This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.

Quickstart Guide

Installation Guide

STEP 1

• Turn off the circuit breaker before installation.
• Cut out the 6.33” housing size on the Installation Template, then tape it onto the ceiling in the desired location.
• Cut the ceiling hole using the Installation Template as a guide.

STEP 2

• Open the junction box and remove the appropriate knockout.

STEP 3

• Thread cable connector through knockout, secure wires with screws, attach cable connector nut on opposite side, & connect supply & junction wires with wire nuts. Black to Black (Live) ; White to White (Neutral)
• Tuck connected wires inside the junction box and close the cov

STEP 4

Note: This step applies exclusively to the Selectable Slims. Slide the CCT Switch to choose from 5 colour temperatures. Insert junction box through the ceiling hole. New Construction: Secure to studs, joists, or similar fixed structural units. Remodel: Do not require to secure to studs, joists, or similar fixed units.

STEP 5

• Attach the fixture to the junction box using the connector as shown in image (1).
• Tighten the connector by hand (2).

STEP 6

• Push up spring clips and insert fixture into ceiling.
• Turn on the circuit breaker and test the light.

Product Details

Recommended Dimmers

Specifications

Common Troubleshooting

Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy- to-follow solutions for any problem. If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts are happy to help brighten your day.

Light Distribution Angle

Not a lighting nerd? No worries, you can skip this page

Customer Support

Warranty Policy

Scan for the full compatible dimmer list

This product is covered by our industry-leading 7-year warranty. It gets even better – scan the QR code for 2 extra years of protection!

30-Day Return Policy

At Sunco, we value our customers and stand by the quality and performance of our products.If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.

contact

Our Los Angeles team of lighting experts is here to assist you with all your needs! Contact us at

• Email: support@sunco.com
• Call or Text: 844-334-9938

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>