TAC 40-15020T Side Steps Running Boards Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 40-15020T Side Steps Running Boards
Product Information
Specifications:
- Product: 4INCH SIDEBARS
- Vehicle Compatibility: 2021-2024 FORD BRONCO 4DR
- Part Number: 40-15020T
- Website: www.tacautoparts.com
Product Usage Instructions
Parts List:
- 1 Driver/Left PNC Sidebar
- 1 Passenger/Right PNC Sidebar
- 2 Front Mounting Brackets
- 2 Center Mounting Brackets
- 2 Rear Mounting Brackets
- 12 10mm x 30mm Hex Bolts
- 12 10mm Lock Washers
- 12 10mm x 27mm OD x 3mm Flat Washers
- 12 8mm x 25mm Combo Bolts
Installation Instructions:
-
Front Mounting:
Attach the Passenger/Right Front Mounting Bracket to the front location using the provided hardware: 2 10mm Hex Bolts, 2 10mm Lock Washers, and 2 10mm Flat Washers. -
Center Mounting:
Attach (1) Passenger/Right Rear Mounting Bracket to the center location using the provided hardware: 2 10mm Hex Bolts, 2 10mm Lock Washers, and 2 10mm Flat Washers. -
Rear Mounting:
Attach the Passenger/Right Sidebar to the Mounting Brackets at the rear mounting location using the provided 2 8mm Combo Bolts.
Cleaning Instructions:
To protect your investment, do not use any type of polish or wax that may
contain abrasives that could damage the finish. Mild soap may be used to clean
the Sidebars.
FAQ
Q: Can I use abrasive polish or wax on the Sidebars?
A: No, it is recommended not to use any type of polish or wax that may contain
abrasives that could damage the finish. Mild soap is suitable for cleaning.
PARTS LIST
| 1 | Driver/Left PNC Sidebar | 12 | 10mm x 30mm Hex Bolts |
|---|---|---|---|
| 1 | Passenger/Right PNC Sidebar | 12 | 10mm Lock Washers |
| 2 | Front Mounting Brackets | 12 | 10mm x 27mm OD x 3mm Flat Washers |
| 2 | Center Mounting Brackets | 12 | 8mm x 25mm Combo Bolts |
| 2 | Rear Mounting Brackets |
PROCEDURE
- REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Starting from underneath the Passenger/Right body panel, locate the front mounting location and the threaded holes in the body panel, (Figure 1). Remove the plastic plugs covering the holes.
- Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the front location with (2) 10mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Figure 2). Do not tighten the hardware.
- Repeat Steps 2 & 4 to attach the Center Mounting Bracket and Rear Mounting Bracket to the center and rear locations, (Figures 3—6). Do not tighten the hardware. Note: The Rear Mounting Brackets have a small hole in the back, (Figure 4).
- Select the Passenger/Right PNC Sidebar. Place the Sidebar onto the cradles of the Mounting Brackets. IMPORTANT: Do not rotate or slide the Sidebar front to back or damage to the finish may result. Attach the Sidebar to the Mounting Brackets with (6) 8mm Combo Bolts, (Figure 7). Do not tighten the hardware.
- Level and adjust the PNC Sidebar and tighten all hardware.
- Repeat Steps 2—6 to attach the Driver/Left PNC Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Installation
Passenger/Right side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>