POWERMATIC PM2013BT Woodworking Bandsaw with Armor Glide Instruction Manual

POWERMATIC PM2013BT Woodworking Bandsaw with Armor Glide

Product Information

Specifications:

• Product: 20 and 24 Band Saws
• Models: 2013 and 2415
• Manufacturer: WALTER MEIER (Manufacturing), Inc.
• Address: 427 New Sanford Rd. LaVergne, TN 37086
• Phone: 800-274-6848
• Website: www.powermatic.com.

Product Usage Instructions

• Safety Guidelines:
  Before using the band saw, ensure you have read and understood the entire owner’s manual for assembly and operation. Always comply with the safety warnings provided in the manual and on the machine.

• Proper Use and Training:
  This band saw is intended for use by trained personnel only. Do not operate the machine if you are not familiar with its safe operation. Obtain proper training before use.

• Personal Protective Equipment (PPE):
  Always wear approved safety glasses or face shields while using the band saw. Avoid loose clothing, and jewelry, and wear ear protectors during extended operation periods.

• Workspace Safety:
  Work in a well-ventilated area to reduce exposure to harmful chemicals from sawing activities. Ensure the machine is properly grounded, and make all adjustments or maintenance tasks with the machine unplugged.

• Machine Operation:
  Keep safety guards in place at all times when the machine is in use. Check for damaged parts before operation and ensure that all guards are properly functioning.

• Power Supply:
  Before connecting the machine to the power supply, ensure the switch is in the OFF position. Remove adjusting keys and wrenches before turning on the machine.

Frequently Asked Questions

What should I do if a part of the band saw is damaged?

If you notice any damaged part on the band saw, do not operate the machine. Carefully inspect the damaged part to ensure it will function correctly before use. Damaged parts should be repaired or replaced before further operation.

Can I use the band saw for purposes other than its intended use?

No, it is important to use the band saw only for its intended purpose. Using it for other purposes may lead to injury or damage, and void any warranties provided by the manufacturer.

Warranty and Service

Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your POWERMATIC® tools. For the name of an Authorized Service Center in your area call 1-800-274-6848.

MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor or visit powermatic.com.

WARRANTY
POWERMATIC products carry a limited warranty which varies in duration based upon the product.

WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools, abrasives and other consumables are excluded from warranty coverage.

WHO IS COVERED?
This warranty covers only the initial purchaser of the product.

WHAT IS THE PERIOD OF COVERAGE?
The general POWERMATIC warranty lasts for the period specified in the product literature of each product.

WHAT IS NOT COVERED?

• The Five Year Warranty does not cover products used for commercial, industrial or educational purposes. Products with a Five Year Warranty that are used for commercial, industrial or education purposes revert to a One Year
• Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.

HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name of the location nearest you, please call 1-800-274-6848. You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price, at our option. We will return the repaired product or replacement at our expense unless it is determined by us that there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will, at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be responsible for the handling and shipping costs of the return.

HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.

LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER (MANUFACTURING) INC., SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

Walter Meier sells through distributors only. The specifications in Walter Meier’s catalogues are given as general information and are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

Safety Warning

1. Read and understand the entire owner’s manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This band saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a band saw, do not use it until proper training and knowledge have been obtained.

5. Do not use this band saw for other than its intended use. If used for other purposes, WMH Tool Group disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields while using this band saw. Everyday eyeglasses only have impact-resistant lenses; they are not safety glasses.

7. Before operating this band saw, remove ties, rings, watches and other jewellery, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

   • Lead from lead-based paint.
   • Crystalline silica from bricks, cement and other masonry products.
   • Arsenic and chromium from chemically treated lumber.
     Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11. Make certain the switch is in the OFF position before connecting the machine to the power supply.

12. Make certain the machine is properly grounded.

13. Make all machine adjustments or maintenance with the machine unplugged from the power source.

14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately.

16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17. Provide adequate space surrounding the work area and non-glare, overhead lighting.

18. Keep the floor around the machine clean and free of scrap material, oil and grease.

19. Keep visitors a safe distance from the work area. Keep children away.

20. Make your workshop child-proof with padlocks, and master switches or by removing starter keys.

21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury.

22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. Do not overreach or use excessive force to perform any machine operation.

23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and safer.

24. Use recommended accessories; improper accessories may be hazardous.

25. Maintain tools with care. Keep the blade sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.

26. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not use your hands.

27. Do not stand on the machine. Serious injury could occur if the machine tips over.

28. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

29. Remove loose items and unnecessary workpieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

• CAUTION: This means that if precautions are not heeded, it may result in minor injury and/or possible machine damage.
• WARNING: This means that if precautions are not heeded, it may result in serious injury or possibly even death.

Introduction

This manual is provided by Walter Meier (Manufacturing), Inc. covering the safe operation and maintenance procedures for a Powermatic Model 2013 or 2415 Band Saw. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble-free operation if used according to the instructions outlined in this manual. If there are any questions or comments, please contact either your local supplier or Walter Meier. Walter Meier can also be reached at our website: www.waltermeier.com.

Specifications

• Model Number ………………………………………………………. 2013……………………………………………. 2415
• Stock Number (2HP, 1Ph, 230V) …………………………….1791257……………………………………………….. na
• Stock Number (3HP, 1Ph, 230V) ……………………………………. na………………………………………..1791259
• Stock Number (3HP, 3Ph, 230/460V*)………………………1791258……………………………………………….. na
• Stock Number (5HP, 3Ph, 230/460V*)……………………………… na………………………………………..1791260
• Blade Speeds (SFPM) ………………………………. 2,000 and 4,000…………………………….. 2,000 and 4,000
• Thickness Capacity, Maximum (in.) ……………………………. 12-3/8………………………………………….. 14-3/8
• Width Capacity, Maximum (in.) ………………………………………. 20……………………………………………….. 24
• Table Size (in.) ……………………………………………………..24 x 24………………………………………….24 x 28
• Table Tilt (deg.) …………………………………………..45 right, 10 left………………………………..45 right, 10 left
• Approximate Blade Length (in.)……………………………….. 158-1/2………………………………………… 180-1/2
• Blade Widths (in.) ……………………. 1/4 minimum, 1-1/2 maximum……………. 1/4 minimum, 1-1/2 maximum
• Switch ……………………………………………………………… magnetic………………………………………. magnetic
• Dust Collection Minimum CFM Required ………………………… 600……………………………………………… 600
• Table Height at 90o (in.) ………………………………………….. 35-1/4………………………………………….. 35-3/8
• Floor Space Required (in.) ………………………………… 39 x 45-1/2……………………………………. 39 x 51-1/2
• Shipping Weight (lbs.) ………………………………………………… 970……………………………………………. 1190

pre-wired 230 volt NOTE: For 460V operation, magnetic switch (part no. 2013-102B for model 2013; and part no. 2415-102B for model 2415) must be purchased separately and installed. A qualified electrician is recommended.

The above specifications were current at the time this manual was published, but because of our policy of continuous improvement, Walter Meier reserves the right to change specifications at any time and without prior notice, without incurring obligations.

Features and Terminology

(Model 2415 shown)

Floor Diagrams

Unpacking

• Open the shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Band Saw is set up and running properly.
• Compare the contents of your container with the following parts list to make sure all parts are intact. Missing parts, if any, should be reported to your distributor. Read the instruction manual thoroughly for assembly, maintenance and safety instructions.

Contents of the Shipping Container

• 1 Band Saw

• 1 Miter Gauge

• 1 Front Rail

• 1 Rear Rail

• 1 Guide Rail

• 1 Fence

• 1 Fence Body

• 1 Combination Wrench – 10/12mm

• 1 Bag of Fasteners, containing:

  • 2 Hex Cap Screws, 5/16-18 x 1-1/4”
  • 4 Hex Cap Screws, 5/16-18 x 3/4”
  • 6 Flat Washers, 5/16”
  • 6 Lock Washers, 5/16”
  • 7 Hex Cap Screws, 1/4-20 x 5/8”
  • 7 Flat Washers, 1/4”
  • 7 Lock Washers, 1/4”

• 1 Owner’s Manual

• 1 Warranty Card

WARNING
Read and understand the entire contents of this manual before attempting set- up or operation! Failure to comply may cause serious injury.

Assembly

Tools required for assembly:

• Forklift or hoist with straps
• 10-12mm wrench (provided)
• 14mm wrench

(NOTE: A socket wrench set may speed assembly time)

Remove all crating and plastic from around the band saw. Remove any lag screws or holding straps that secure the band saw to the wood pallet. Use a hoist or forklift with straps to lift the band saw from the pallet. (Do NOT place forks or straps directly under the band saw table to lift it.) Move the band saw to its permanent location, which should be dry and well-lit, with enough space on all sides to handle long stock or perform routine maintenance on the machine. Make sure the floor can support the weight of the machine. Areas of the Band Saw have been given a protective coating at the factory. This should be removed with a soft cloth moistened with kerosene or mineral spirits. Do not get solvents near plastic or rubber parts, and do not use an abrasive pad as it may scratch metal surfaces.

Installing Fence and Rails

1. Mount the front rail (A, Figure 1) to the saw table with two 5/16 x 1-1/4 hex cap screws, two 5/16 lock washers, and two 5/16 flat washers. Screws should be placed horizontally in approximately the centre of the slot. Hand-tighten the screws.
2. Mount the rear rail (B, Figure 1) to the table with two 1/4 x 5/8 hex cap screws, two 1/4 lock washers, and two 1/4 flat washers. Hand-tighten the screws.
3. Push the front and rear rails upward (toward the table top) as far as they will go.
4. Tighten the two hex cap screws holding the front rail to the table, with a 12mm wrench. Tighten the two hex cap screws holding the rear rail to the table with a 10mm wrench.
5. Attach the guide rail (C, Figure 1) to the front rail with five 1/4 x 5/8 hex cap screws, five 1/4 lock washers, and five 1/4 flat washers. The scale on the guide rail should face toward the operator. Hand-tighten the screws only.
6. Attach the fence (D, Figure 2) to the fence body (E, Figure 2) with four 5/16 x 3/4 hex cap screws, four 5/16 lock washers, and four 5/16 flat washers. Hand-tighten the screws only.
7. Place the fence assembly onto the guide rail and against the edge of the mitre slot, as shown in Figure 2. The hook at the rear of the fence should fit under the rear rail (see Figure 5).
8. The fence must align parallel to the mitre slot along the entire length of the fence.
9. Lock the fence by pushing down the lock handle (G, Figure 2). Because the screws are only hand-tight, you can shift the fence slightly as needed until the fence parallels the mitre slot.
10. When the fence has been properly aligned to the mitre slot, tighten the four hex cap screws (F, Figure 2) with a 12mm wrench. Make sure the fence remains parallel to the mitre slot as you tighten the screws. (NOTE: This alignment will again be checked once the guide rail has been tightened.)
11. Move the fence assembly to the other side of the blade so that the pointer (Figure 3) on the fence body points to “zero” on the scale. Lock the fence by pushing the handle down.
12. Move the guide rail with the locked fence until the fence is flush against the blade. (Do not force the fence into the blade so that the blade bends.) See Figure 3. Do not unlock the fence to perform this. Move the fence and guide rail together when establishing the zero point.
13. Tighten the five hex cap screws that hold the guide rail to the front rail, with a 10mm wrench. NOTE: After tightening the guide rail, double-check that the fence is still parallel to the mitre slot. Make additional adjustments if needed.
14. Check the clearance between the table and the fence. The fence should not rub against the table surface but be slightly above it. This gap should be the same at the front of the table as it is at the rear. See Figure 4.
15. If the gap between the fence and the table is not consistent, loosen either of the hex nuts on the hook (Figure 5) and rotate the sliding pad until the fence/table gap is consistent across the full length of the table. When this is achieved, tighten both hex nuts.
16. Check the adjustment of the hook at the rear of the fence. The hook should be positioned so that it overlaps the rear rail by approximately 1/8”. See Figure 5. To adjust the hook, loosen the upper hex nut (Figure

6. and slide the hook in or out as needed. Re-tighten the upper hex nut.

Dust Collection
The use of a dust collection system is strongly recommended for this band saw. It will help keep the shop clean as well as reduce any potential health hazards caused by inhalation of wood dust. The collector should have a capacity sufficient for this size machine (minimum of 600 CFM). Attach the hose of the dust collector to the 4” dust port below the band saw table (Figure 6). Secure with a hose clamp or duct tape.

NOTE:
A dryer vent hose is not acceptable for wood dust collection.

Grounding Instructions

WARNING
Electrical connections must be made by a qualified electrician in compliance with all relevant codes. This machine must be properly grounded to help prevent electrical shock and possibly fatal injury.

• This machine must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
• Repair or replace a damaged or worn cord immediately.
• Make sure the voltage of your power supply matches the specifications on the motor plate of the Band Saw. The machine should be connected to a dedicated circuit, and protected by a circuit breaker or time delay fuse, with minimum amp ratings as shown in Table 1. Local codes take precedence over recommendations.

Extension cords

• The use of an extension cord is not recommended for the 2013 or 2415 Band Saw. But if one is necessary, make sure the cord rating is suitable for the amperage listed on the machine’s motor plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
• Use the chart in Figure 7 as a general guide in choosing the correct size cord. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.

230 Volt, Single Phase Operation

• As received from the factory, the single-phase model of the Band Saw is designed to run on 230-volt power. You may either install a plug or “hard-wire” the Band Saw directly to a service panel.
• If connecting a plug, use a proper UL/CSA listed 2-pole, 3-wire grounding plug suitable for 230V operation.
• If the Band Saw is to be hard-wired to a panel, make sure a disconnect is available for the operator. During hard-wiring of the Band Saw, make sure the fuses have been removed or the breakers have been tripped in the circuit to which the Band Saw will be connected. Place a warning placard on the fuse holder or circuit breaker to prevent it from being turned on while the machine is being wired.

230 Volt, Three Phase Operation
The three-phase model is factory wired for 230 volts but can be converted to 460 volts if so desired (see “Converting From 230 Volt to 460 Volt”). You may either install a plug or “hard-wire” the Band Saw directly to a service panel.

subject to local codes

Table 1

Recommended Gauges (AWG) of Extension Cords

Amps

| **Extension Cord Length ***
---|---
25

feet

| 50

feet

| 75

feet

| 100

feet

| 150

feet

| 200

feet

< 5| 16| 16| 16| 14| 12| 12
5 to 8| 16| 16| 14| 12| 10| NR
8 to 12| 14| 14| 12| 10| NR| NR
12 to 15| 12| 12| 10| 10| NR| NR
15 to 20| 10| 10| 10| NR| NR| NR
21 to 30| 10| NR| NR| NR| NR| NR

based on limiting the line voltage drop to 5V at 150% of the rated amperes.

NR: Not Recommended.

Figure 7

If you are connecting a plug, use a proper UL/CSA listed 3-pole, 4-wire grounding plug suitable for 230-volt operation. If the Band Saw is to be hard- wired to a panel, make sure a disconnect is available for the operator. During hard-wiring of the Band Saw, make sure the fuses have been removed or the breakers have been tripped in the circuit to which the Band Saw will be connected. Place a warning placard on the fuse holder or circuit breaker to prevent it from being turned on while the machine is being wired.

Converting from 230 Volt to 460 Volt (Three Phase Only)
To convert from 230 volts to 460 volts:

1. Remove the four Phillips head screws on the switch plate (Figure 8) and tilt the switch plate down. Then remove the cover of the switch box.
2. Replace the current contactor with the 460V magnetic contactor (part no. 2013-102B for model 2013; part no. 2415-102B for model 2415; purchased separately).
3. Re-connect the motor leads according to the diagrams inside the motor junction box. These diagrams are also found on pages 56 and 57 of this manual. (The diagram in the motor junction box should take priority.)
4. Change the lamp input power from 230V to 460V in the panel of the transformer (Figure 9) per the diagrams on pages 56 and 57.
5. If using a plug, install a proper UL/CSA listed plug suitable for 460V operation.

IMPORTANT:
Consult the diagrams on pages 56 and 57 for clarification of any of these changes on 230V to 460V conversion.

Three-Phase Test Run
On the three-phase unit, after the wiring has been completed, you should check that the wires have been connected properly:

1. Open the lower front door of the Band Saw.
2. Connect the machine to a power source and press the start button, shown in Figure 28, for just an instant, then press the stop button. (See “Operating Controls” on page 21 for further information on the control buttons.)
3. The lower wheel should rotate clockwise as viewed from the front of the machine. If the rotation of the lower wheel is incorrect, disconnect the machine from power.
4. Switch any two of the three wires at “R, S, T” (see “Electrical Connections”, pages 56 and 57) and re-connect the machine to a power source.

Adjustments

Table Tilt

1. Loosen the lever (Figure 10).

2. Rotate the handwheel (Figure 10) clockwise to tilt the table up to 45 degrees to the right, or counterclockwise to tilt the table up to 10 degrees to the left (as viewed from the operator’s position).
   NOTE: If you tilt the table to the left, you must first remove the stop screw from the machine, shown in Figure 12.

3. Tighten the lever (Figure 10).

NOTE:
The lever, shown in Figure 10, can be pivoted so that it doesn’t contact the band saw surface. Simply lift straight out on the lever and rotate it on the pin, then release it making sure it seats itself on the pin.

90° Table Stop
The 90° stop, shown in Figure 12, ensures the table will always be perpendicular to the blade after the table is returned to a horizontal position.

Check and adjust this 90° stop as follows:

1. Disconnect the machine from the power source.
2. Loosen the lever (Figure 10) and tilt the table left until the stop screw rests against the metal platform of the Band Saw, as shown in Figure 12.
3. Place a square on the table and against the blade to check that the table is 90° to the blade. See Figure 11.
4. If the table and blade are not square, loosen the lock nut (Figure 12) with a 14mm wrench, and turn the head of the stop screw with a 17mm wrench. Turn the screw as needed until there is no longer light showing between the square and the blade.
5. Tighten the lock nut (Figure 12) to secure the table stop in position.
6. Tighten the lever (Figure 10).
7. Check that the scale pointer (Figure 10) is at zero. If necessary, loosen the screw on the pointer and shift the pointer to zero. Tighten the screw.

Installing/Changing Blades

CAUTION
Always wear gloves when handling blades. New blades are usually packaged in a coiled position; to prevent injury uncoil them slowly and carefully while wearing gloves and safety glasses.

1. Disconnect the machine from the power source.

2. Decrease blade tension by rotating the blade tension handwheel (A, Figure 14) according to the arrow direction in Figure 14, until the handwheel stops.

3. Remove the table insert (Figure 13).

4. Remove the set screw at the end of the slot (Figure 13) with a 4mm (or 5/32”) hex wrench.

5. Lower the upper blade guide assembly by loosening the knob (B, Figure 14) and rotating the handwheel (C, Figure 14).

6. Open the upper and lower front doors.

7. Carefully remove the blade from between the upper and lower blade guides. Remove the blade from the upper and lower wheels.

8. Guide new blade through table slot. Place the blade in the upper and lower blade guides.
   NOTE: Make sure blade teeth point down toward the table, and toward the front of the saw.

9. Position the blade in the middle of the upper and lower wheels.

10. Replace table insert and set screw.

11. Before operating the band saw, the new blade must be tensioned and tracked properly. Find instructions for tensioning and tracking the blade under “Blade Tension” and “Blade Tracking.” The blade guides must also be set properly according to the instructions on pages 18 and 19.

Blade Tension

1. Disconnect the machine from the power source.
2. Close both upper and lower doors.
3. Rotate blade tension handwheel to set the blade tension, according to the arrow directions in Figure 14.
4. The gauge (D, Figure 14) indicates the approximate tension according to the width of the blade in inches. Initially, set the blade tension to correspond to the width of your blade. As you become familiar with the saw, you may find it necessary to change the blade tension from the initial setting.
5. Changes in blade width and the type of material being cut will affect blade tension. Keep in mind that too little or too much blade tension can cause blade breakage and/or poor cutting performance.

TIP:
When the band saw is not being used, slightly release the tension on the blade – this will prolong the blade’s life. Make a note of the specific tension setting for that particular blade, as shown on the gauge (D, Figure 14). The tension can then be re-set quickly when band saw operations are resumed.

Blade Tracking
“Tracking” refers to the position of the saw blade on the wheels while the machine is in operation. Tracking has been factory-adjusted. However, it should be checked occasionally, including after every blade change.

IMPORTANT:
Make tracking adjustments with the knob (F, Figure 15). DO NOT use screws (G, Figure 15); these were used by the manufacturer for wheel alignment and should NOT be used for blade tracking.

To inspect and adjust tracking, proceed as follows:

1. Disconnect the machine from the power source.

2. The blade must be properly tensioned before adjusting blade tracking. Make sure the blade guides and other parts of the machine will not interfere with the movement of the blade.

3. Open the upper front door to expose the upper wheel. Rotate the wheel clockwise by hand, and observe the position of the blade on the wheel. The blade should ride upon the centre of the wheel (Figure 16).

4. If the blade tends to move toward the edge of the wheel, loosen the wing nut (E, Figure 15) and slightly rotate the knob (F, Figure 15). Rotating the knob clockwise will cause the blade to move toward the rear edge of the wheel. Rotating the knob counterclockwise will cause the blade to move toward the front edge of the wheel.
   NOTE: This adjustment is sensitive; perform it in small increments and give the blade time to react to the changes, as you continue to rotate the wheel.

5. When the blade is tracking properly in the centre of the wheel, re-tighten the wing nut (E, Figure 15).

6. Close the upper front door.

Upper Blade Guide Assembly

1. Disconnect the machine from the power source.
2. Loosen the lock knob (see B, Figure 14) and raise or lower the upper blade guide assembly by turning the handwheel (C, Figure 14).
3. Position the blade guide assembly about 3/16” above the material to be cut. The scale (J, Figure 14) shows the distance from the bottom of the upper blade guides to the table surface.
4. Tighten the lock knob (B, Figure 14).

Upper Blade Guides and Upper Support Bearing
To adjust the bearing guides for proper blade control, proceed as follows.

1. Disconnect the machine from the power source.
2. The blade must already be tensioned and tracked properly.
3. Loosen the locking handle (A, Figure 17).
4. Adjust the guide bracket (B, Figure 17) by rotating the knob (G, Figure 17) until the front of the guide bearings (C, Figure 17) are just behind the blade’s gullet (curved area at the base of the tooth). See Figure 18.
5. Tighten the locking handle (A, Figure 17).
6. Loosen set screw (D, Figure 17) on the guide bearing assembly, with a 3mm hex wrench. (Figure 17 shows the set screw for the right-hand bearing; the set screw for the left-hand bearing is shown in Figure 19.)
7. The guide bearing rotates on an eccentric shaft. Adjust the guide bearing, by rotating the knob (H, Figure 19) until the guide bearing rests lightly against the blade. Do not force the guide bearing against the side of the blade.
8. Tighten the set screw (D, Figure 17).
9. Repeat the process for the other guide bearing. After adjustment, make sure the set screw (D, Figure 19) is tightened.
10. Loosen nut (E, Figure 19).
11. Adjust the support bearing using the knob (F, Figure 19) until the space between the support bearing and the back edge of the blade is approximately 1/64”. A convenient way to achieve this spacing is by placing a dollar bill folded twice (four thicknesses of a dollar bill is approximately 1/64”) between blade and support bearing.
12. Adjust the support bearing until it lightly contacts the dollar bill.
13. When the support bearing adjustment is complete, remove the dollar bill and tighten nut the (E, Figure 19).

Lower Blade Guides and Lower Support Bearing

1. Disconnect the machine from the power source.
2. The blade must already be tensioned and tracked properly.
3. Loosen two hex cap screws (J, Figure 20).
4. Adjust the guide bracket (K, Figure 20) so that the front of the guide wheels is just behind the blade’s gullet (curved area at the base of the tooth).
5. Tighten the two hex cap screws (J, Figure 20).
6. Loosen lock ring (L, Figure 20) on the guide wheel assembly.
7. Rotate the knob (M, Figure 20) until the guide wheel rests lightly against the blade. Do not force the guide wheel against the side of the blade.
8. Tighten the lock ring (L, Figure 20).
9. Repeat this adjustment for the guide wheel on the opposite side.
10. Loosen thumb screw (N, Figure 20).
11. Slide the shaft of the support bearing until the space between the support bearing and the back edge of the blade is approximately 1/64”. A convenient way to achieve this spacing is by placing a dollar bill folded twice (four thicknesses of a dollar bill is approximately 1/64”) between blade and support bearing.
12. Adjust the support bearing until it lightly contacts the dollar bill.
13. The bearing holder on the shaft is eccentric. Rotate the support bearing until the back edge of the blade overlaps the front face of the support bearing by approximately 1/8”. See Figure 21.
14. When adjustments to the support bearing are complete, tighten the thumb screw (N, Figure 20).

Miter Gauge
A mitre gauge is provided for crosscutting operations. Install the mitre gauge by sliding the end of the mitre gauge bar into the T-slot in the table, as shown in Figure 22.

To adjust the angle of the mitre gauge:

1. Loosen the handle (A, Figure 22).
2. Rotate the gauge body until the pointer (B, Figure 22) lines up with the desired angle on the scale. You may have to pivot the stop (C, Figure 22) out of the way to allow the body to rotate.
3. Tighten the handle (A, Figure 22).
4. There are three stops – at 90° and 45° left and right. Each of these can be adjusted by loosening the hex nut (D, Figure 22) and turning the screw (E, Figure 22) as needed. Re-tighten the hex nut (D, Figure 22) when the adjustment is finished.
5. Make sure the stop (C, Figure 22) is flipped back into place.

Belt Tension
The drive belt and pulleys are properly adjusted at the factory. However, belt tension should be occasionally checked. The belt will need to be re-tensioned after belt replacement or changing speeds.

1. Disconnect the machine from the power source.
2. Open the lower back door.
3. Loosen the four hex nuts on the motor plate (A, Figure 23).
4. Turn the tension screw (B, Figure 23) counterclockwise to reduce tension (for example, to remove the belt) or clockwise to increase the tension on the belt.
5. Check the tension by pushing down with moderate pressure against the centre of the belt (Figure 24). An adequately tensioned belt will deflect about 1/2”.
6. Tighten the hex nut on the tension screw (B, Figure 23) and tighten the four hex nuts (A, Figure 23).

NOTE:
A new belt may stretch slightly during the “breaking in” process, and the tension may need to be checked and adjusted occasionally during this period.

Belt Alignment
If the drive belt is not aligned properly, it can be aligned with one or more of the four set screws located behind the steel plate. Figure 25 shows two of the set screws.

1. Loosen the four hex nuts (A, Figure 23)
2. Rotate clockwise one of the set screws (Figure 25) with a 4mm hex wrench, to push out the motor plate at that point. This will shift slightly the angle of the motor. Use whichever set screw is most effective in adjusting the angle of the motor until the drive belt is aligned.
3. Confirm the alignment of the drive belt by placing a straight edge against the faces of both pulleys, as shown in Figure 26. If the straight edge lies flush against both pulleys, then the pulleys and belt are aligned.
4. Re-tighten the four hex nuts (A, Figure 23).

Blade Speed Adjustment
The bandsaw will operate at 2,000 or 4,000 SFPM (surface feet per minute). Figure 27 shows the appropriate belt position to achieve each speed.

To change the speed:

1. Disconnect the machine from the power source.
2. Loosen the four hex nuts (A, Figure 23) and rotate the tension screw (B, Figure 23) counterclockwise to release tension on the belt.
3. Slide the belt onto the appropriate set of pulleys (Figure 27). Make sure the belt is aligned properly.
4. Re-tension the belt (see under “Belt Tension”) and securely tighten all four hex nuts on the motor plate (A, Figure 23).

Operating Controls

The START (green) and STOP (red) control buttons are mounted to the column (Figure 28). After the STOP button has been pushed, it remains engaged. Rotate the STOP button clockwise to release it. The Band Saw can now be restarted with the START button.

WARNING
After the machine is shut off, allow the wheels and blade to come to a complete stop before opening the doors, making adjustments, or leaving the area.

Brake Pedal

• An alternate method of stopping the machine is to press the brake pedal, as shown in Figure 29. The band saw will shut off when the brake pedal is pressed.
• The brake pedal is also useful for stopping the blade quickly, instead of waiting for the blade to coast slowly to a stop after the machine has been shut off.
• Re-start the saw by pressing the start button on the column.

Operation

General Procedure

1. Make sure the blade is adjusted correctly for tension and tracking.

2. Adjust the blade guide assembly so that the guide bearings are just above the workpiece (about 3/16”) allowing minimum exposure to the blade. See Figure 30.

3. If using the fence, move it into position and lock it to the guide rail. If you are using the mitre gauge for a crosscut, the fence should be moved safely out of the way.

4. Turn on the band saw and allow a few seconds for the machine to reach full speed.
   WARNING: Whenever possible, use a push stick, hold-down, power feeder, jig, or similar device while feeding stock, to prevent your hands from getting too close to the blade.

5. Place the straightest edge of the workpiece against the fence, and push the workpiece slowly into the blade. Do not force the workpiece into the blade.
   CAUTION: When cutting, do not overfeed the blade; overfeeding will reduce blade life, and may cause the blade to break.

6. When cutting long stock, the operator should use roller stands, support tables, or an assistant to help stabilize the workpiece.

Ripping
Ripping is cutting lengthwise down the workpiece, and with the grain (of wood stock). See Figure 31.

Crosscutting

• Crosscutting is cutting across the grain of the workpiece while using the mitre gauge to feed the workpiece into the blade.
• Slide the bar of the mitre gauge into the end of the slot on the table.
• The right hand should hold the workpiece steady against the mitre gauge, while the left-hand pushes the mitre gauge past the blade, as shown in Figure 32.
• Do not use the fence in conjunction with the mitre gauge. The offcut of the workpiece must not be constrained during or after the cutting process.

CAUTION
Using the fence in conjunction with the mitre gauge can cause binding and possible damage to the blade.

Resawing

• Resawing is the process of slicing stock to reduce its thickness, or to produce boards that are thinner than the original workpiece. Figure 33 demonstrates resawing.
• The ideal blade for resawing is the widest one the machine can handle, as the wider the blade the better it can hold a straight line.
• When resawing thin stock, use a push block, push stick, or similar device to keep your hands away from the blade.

Blade Lead

• Blade drift, or “lead,” is a problem that may occur when the blade begins to wander off the cutting line even when the band saw fence is being used. Figure 34 shows an example of blade lead.
• Blade lead can be caused by several factors, and these should all be checked and corrected if necessary:
  • The fence is not parallel to mitre slot and blade.
  • The blade is not tensioned correctly.
  • The blade is dull.
  • Teeth have too much “set” on one side of the blade.

If replacement of the blade is not currently an option, the blade lead can be compensated for by skewing the fence. Proceed as follows:

1. Cut a scrap piece of wood about the same length as the band saw table, and joint one edge along its length, or rip it on a table saw to give it a straight edge.
2. Draw a line on the board parallel with the jointed, or straight edge of the board.
3. Move the band saw fence out of the way, and carefully make a freehand cut along your drawn line on the board. Stop about midway on the board, and shut off the band saw (allow the blade to come to a complete stop) but do not allow the board to move.
4. Clamp the board to the table.
5. Slide the band saw fence over against the board until it contacts the straight edge of the board at some point. Lock the fence down.
6. Loosen the four hex cap screws at the top of the fence (see Figure 3) and shift the fence until it is parallel to the board along its length.
7. Re-tighten the four hex cap screws.

NOTE:
Skewing the fence to correct blade lead is effective for that particular blade; when a new blade is installed, the fence will probably need re- adjustment.

Blade Selection

Using the proper blade for the job will increase the operating efficiency of your band saw, help reduce necessary saw maintenance, and improve your productivity. Thus, it is important to follow certain guidelines when selecting a blade.

Here are factors to consider when selecting a blade:

• The type of material you will be cutting.
• The thickness of the workpiece.
• The features of the workpiece, such as bends or curves with small radii.

These factors are important because they involve basic concepts of saw blade design. Five (5) blade features are normally changed to meet certain kinds of sawing requirements. They are:

1. width
2. pitch (number of teeth per inch)
3. tooth form (or shape)
4. the “set” of the teeth
5. the blade material itself

Width
Band saw blades come in different standard widths, measured from the back of the blade to the tip of the tooth. Generally, wider blades are used for ripping or making straight cuts, such as resawing. Narrower blades are often used when the part being cut has curves with small radii. (When cutting straight lines with a narrow blade, the blade may tend to wander, causing “blade lead.”)

Pitch

• Pitch is measured in “teeth per inch” (T.P.I.) and can be constant or variable. Figure 35 shows blades with different pitches. A fine pitch (more teeth per inch) will cut slower but smoother. A coarse pitch (fewer teeth per inch) will cut rougher but faster.
• As a rule of thumb, the thicker the workpiece, the coarser will be the blade pitch. If you have to cut a hard or very brittle material, you will probably want to use a blade with a finer pitch to get clean cuts.
• Using a blade with too few teeth may cause vibration and a rough cut, while too many teeth may cause the gullets to fill with sawdust and overheat the blade.
• As a general rule, use a blade that will have no fewer than 6 and no more than 12 teeth in the workpiece at any given time.

Shape

• Figure 36 shows common types of tooth shapes. Tooth shape has an effect on the cutting rate.
• The Regular blade, sometimes called a “raker” blade, has evenly spaced teeth that are the same size as the gullets, and a 0-degree rake angle. These offer precise, clean cuts at slower rates. It is usually a good choice for cutting curves.
• The Skip type has fewer teeth and larger gullets, allowing faster cutting rates than the Regular type, with a slightly coarser finish. It is useful for re-sawing and ripping thick stock.
• The Hook-type blade has larger teeth and gullets and a positive rake angle for more aggressive, faster cutting when re-sawing or ripping thick stock.
• Variable-tooth blades combine features of the other styles and generally produce smooth, quiet cuts.

Set

• The term “set” refers to how the saw teeth are bent or positioned. Bending the teeth creates a kerf that is wider than the back of the blade.
• Set patterns are usually selected depending on the type of material that needs to be cut. Three common set patterns are shown in Figure 37.
• Generally, the Raker set is used for cutting metal workpieces; the Wave set when the thickness of the workpiece changes, such as cutting hollow tubing or structural. The Straight set is most often preferred when cutting wood or plastics.

Material

• Band saw blades can be made from different types of materials. Some of the most common include spring steel, carbon steel, bimetal (carbon steel equipped with a high-speed cobalt steel edge welded to it), or carbide tips.
• Because of the importance of blade selection, it is recommended that you use the blade selection guide.

Blade Breakage
Band saw blades are subject to high stresses and breakage may sometimes be unavoidable. However, many factors can be controlled to help prevent most blade breakage. Here are some common causes of breakage:

1. Misalignment of the blade guides.
2. Feeding workpiece too quickly.
3. Using a wide blade to cut a tight radius curve.
4. Excessive tension.
5. Teeth are dull or improperly set.
6. Upper guides are set too high off the workpiece.
7. Faulty weld on blade.

Maintenance

WARNING
Before doing maintenance, disconnect the machine from the electrical supply by pulling out the plug or switching off the main switch! Failure to comply may cause serious injury.

• Clean the band saw regularly to remove any resinous deposits and sawdust. Keep the mitre slot on the table free of dust and debris. Keep the guide bearings clean and free of resin.
• Grease the rack and pinion system of the guide bar.
• Oil any pins, shafts, and joints. Do not get oil on the pulleys or belts.
• Bearings on the band saw are sealed for life and do not require lubrication.
• Check that the cleaning brush over the lower wheel is working properly; adjust if necessary.
• Remove any deposits from the band wheels to avoid vibration and blade breakage.
• The table surface must be kept clean and free of rust for best results. If rust appears, use a mixture of household ammonia, a good commercial detergent and 000 steel wool. (Alternatively, commercial rust removers can be found at many hardware stores.) Then wash the table down with hot, soapy water, rinse and dry thoroughly.
• Apply a light coat of paste wax to the table. Or, some users prefer talcum powder applied with a blackboard eraser rubbed in vigorously once a week; this will fill casting pores and form a moisture barrier. This method provides a tabletop that is slick and allows rust rings to be easily wiped from the surface. Important also is the fact that talcum powder will not stain wood or mar finishes as wax pickup can.
• If the power cord is worn, cut, or damaged in any way, have it replaced immediately.

Tire Replacement

1. Disconnect the machine from the power source.
2. Remove the blade from the machine.
3. Insert a flathead screwdriver beneath the liptyrethe tire. Pry up the tyre and pull it off the wheel. If this proves difficult, insert a wood wedge or dowel into the opening (see Figure 38), and continue to pry around the perimeter of the wheel until the tyre comes off the wheel.
4. Clean the rim of the band wheel before installing the new tyre.
5. The new tyre can be installed without removing the band wheel from the machine; or, you can remove the band wheel (see “Band Wheel Replacement” for removal instructions) and place it on a workbench, using a home-made jig to secure it while installing the new tyre.
6. Place part of the new tyre over the band wheel and work it onto the rim of the band wheel. If needed, insert a wood dowel beneath the tyre and move the dowel around the perimeter of the band wheel to guide the tyre on.

NOTE:
Although the tyre may look too small, it will stretch around the band wheel with the proper exertion and will form a tight fit. Unlike rubber tyres for many older model band saws, the tyres for the 2013 and 2415 will not require trimming, equalizing, etc., nor do they require an adhesive. Rather, they are ready to use immediately after installation.

Band Wheel Replacement

WARNING
The cast iron band wheels are heavy; use care when removing them.

Disconnect the machine from power, and remove the blade. Loosen and remove the hex nut and flat washer at the wheel’s hub. Carefully pull off the wheel by hand or with a “wheel puller.”

Blade Selection Guide

Identify the material and thickness of your workpiece. The chart will show the recommended PITCH, blade TYPE, and FEED RATE.

Key:

• H – Hook L – Low
• S – Skip M – Medium
• R – Regular H – High

Example: 10/H/M means 10 teeth per inch / Hook Type Blade / Medium Feed.

For Radius Cutting

• Study the part drawing or prototype, or measure the smallest cutting radius required, and locate this radius (in inches) on the chart at the right. Follow the curve to where the approximate blade width is specified. If a radius falls between two of the curves, select the widest blade that will see this radius.
• This procedure should be used for making initial blade selections. These recommendations can, of course, be adjusted to meet specific requirements of a cutting job. Compromises may be necessary if you cannot find all the needed specifications in a single blade.

Troubleshooting

Troubleshooting – Operational Problems

locking mechanism.
The table will not tilt.| The trunnion is not lubricated.| Lubricate trunnion.
The trunnion is jammed.| Disassemble and replace jammed parts.
Table vibration while sawing.|

Incorrect blade speed.

| positiontion belt for the correct speed (see page 21). Alan so, use acceptable feed rate for the material being worked (page 28).
The drive belt is too slack.| Increase tension on the drive belt. (see page 20). Replace the belt if worn.
Incorrect choice of saw blade pitch.| Check the blade selection chart and use the correct blade (see page 28).
Saw dust or debris on the band wheel. Or the tire is worn/damaged.| Keep band wheels clean. Replace tyres if necessary.
Support bearing(s) are worn.| Replace support bearings.
The surface finish on the workpiece is rough.| The saw blade speed is too low.| Increase speed.
The saw blade pitch is too coarse.| Change to a finer pitch blade.
Saw blade cutting inaccurately. Cuts are not straight.| Worn blade teeth or damaged blade.| Replace blade.
The fence is not parallel to the blade.| Align the fence properly (see page 11).
Incorrect adjustment of blade guides.| Adjust blade guides properly (see pages 18 and 19).
Incorrect blade speed used.| Change to the correct speed (see page 2The workpiece
iece is being fed too strongly.| Reduce feed forThe upper
pper blade guides are not located close enough to the workpiece.| Guides should be about 3/16” above the workpiece (see page 22).
Incorrect choice of saw blade for that particular cutting operation.| Change to the correct blade.
Blade tension is too light.| Increase tension (see page 16).
The blade can not be tensioned properly.| Tension springs are fatigued.| Replace tension springs (contact service representative).
Blade forms cracks at the base of teeth.| Teeth not suitable for particular jobs, or are incorrectly set.| Replace with the proper blade for the job.
Blade thickness is not suitable for band wheel diameter.| Replace with proper thickness blade.
Blade forms cracks at the base of teeth. (continued)| The blade sharpincorrectlyreand cbecomesomes overheated.| Sharpen the blade properly or replace it.
---|---|---
Band wheels have become misaligned.| Contact service representative.
Cracks on the back edge of the blade.| The workpiece is being fed too quickly.| Reduce feed speed to lessen the strain on the blade.
Welding on the blis ade not perfectly aligned.| Eliminate the welded part, and re-weld properly, or acquire a new blade.
The support bearing is worn; caused by constant contact with the back of the blade.| Replace the support bearing. Adjust the new bearing according to instructions (see pages 18 and 19).
The blade breaks prematurely.| The feed force is too great.| Reduce feed force.
The blade pitch is too coarse.| Refer to the blade selection chart; use a finer pitch blade (see page 28).
Support bearing not properly supporting blade.| Check the support bearing for correct position and signs of wear. Adjust or replace as needed.
Blade tensioned too tightly.| Reduce tension (see page 16).
Blade breaks close to weld.| The blade overheated during welding.| Have the blade annealed, or eliminate the brittle part and weld correctly?
The blade cooled too rapidly after welding.| Have the blade annealed, or eliminate the brittle parts and weld correctly?
Premature dulling of saw teeth.| Blade “pitch” too fine.| Refer to the blade selection chart (page 28). Use a blade with a coarser pitch.
The feed pressure is too light.| Increase feed pressure.
The cutting rate is too low.| Increase feed pressure and cutting rate.
Incorrect choice of blade.| Re-examine material. Select the proper blade from the chart (page 28).
A chipped tooth or a foreign object lodged in the cut.| Stop the saw and remove the lodged particle. Replace the blade if damaged.

Blade binds in the workpiece.

| Incorrect blade tension or damaged blade.| Correct accordingly.
The blade is too wide for the desired radius.| Select a narrower blade. See chart.

Troubleshooting – Mechanical and Electrical Problems

Trouble

| Probable Cause|

Remedy

---|---|---
Machine will not start/restart or repeatedly trips circuit breaker or blows fuses.| No incoming power.| Verify machine is connected to power source. Make sure START button is pushed in completely, and the STOP button is disengaged. See page 21.
Cord damaged.| Replace cord.
Overload automatic reset has not been reset.| Remove the switch plate from the rear of the column (see page 14) and reset the overload by pushing in completely the OFF (red) button on the magnetic switch. If problem persists, check amp setting on the motor starter.
Band Saw frequently trips.| One cause of overloading trips which are not electrical in nature is too heavy a cut. The solution is to reduce feed pressure into the blade. If too heavy a cut is not the problem, then check the amp setting on the overload relay. Match the full load amps on the motor as noted on the motor plate. If amp setting is correct then there is probably a loose electrical lead.

Check amp setting on motor starter.

Building circuit breaker trips or fuse blows.| Verify that band saw is on a circuit of correct size. If circuit size is correct, there is probably a loose electrical lead. Check amp setting on motor starter.
Switch or motor failure (how to distinguish).| If you have access to a voltmeter, you can separate a starter failure from a motor failure by first, verifying incoming voltage at 220+/-20 and second, checking the voltage between starter and motor at 220+/-

20. If incoming voltage is incorrect, you have a power supply problem. If voltage between starter and motor is incorrect, you have a starter problem. If voltage between starter and motor is correct, you have a motor problem.

Motor overheated.| Clean motor of dust or debris to allow proper air circulation. Allow motor to cool down before restarting.
Motor failure.| If electric motor is suspected, you have two options: Have a qualified electrician test the motor for function or remove the motor and take it to a qualified electric motor repair shop and have it tested.
Machine will not start/restart or repeatedly trips circuit breaker or blows fuses.|

Miswiring of the unit.

| Double-check to confirm all electrical connections are correct. Refer to the appropriate wiring diagrams on pages 54 through 57 to make any needed corrections.
---|---|---

Switch failure.

| If the start/stop switch is suspect, you have two options: Have a qualified electrician test the switch for function, or purchase a new start/stop switch and establish if that was the problem on changeout.
Band Saw does not come up to speed.| Extension cord too light or too long.| Replace with adequate size and length cord.
Low current.| Contact a qualified electrician.

Replacement Parts

Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website for business hours, www.powermatic.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

Parts List: Saw Body Assembly (2013 Band Saw)

• Index No.  Part No.                  Description                                                  Size                          Qty

• 1 ………….. 2013-101……………..Body …………………………………………………………………………………….. 1

• 2 ………….. 2013-102N …………..Magnetic Switch ………………………………………..1Ph, 230V ……………… 1
  ……………. 2013-102CSN……….Contactor Switch for 1 Phase (not shown) …………………………………….. 1
  ……………. 2013-102ORN ………Overload Relay for 1 Phase (not shown) ………………………………………. 1
  ……………. 2013-102AN …………Magnetic Switch ………………………………………..3Ph, 230V ……………… 1
  ……………. 2013-102ACSN …….Contactor Switch for 230V 3 Phase (not shown) …………………………….. 1
  ……………. 2013-102AORN …….Overload Relay for 230V 3 Phase (not shown)……………………………….. 1
  ……………. 2013-102B …………..Magnetic Switch ………………………………………..3Ph, 460V ……………… 1
  ……………. 2013-102BCS ……….Contactor Switch for 460V 3 Phase (not shown) …………………………….. 1
  ……………. 2013-102BOR ………Overload Relay for 460 3 Phase (not shown) …………………………………. 1

• 3 ………….. 2013-103A …………..Switch Plate …………………………………………………………………………… 1

• 4 ………….. TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 8

• 5 ………….. TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 6

• 6 ………….. TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 2

• 7 ………….. TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 4

• 8 ………….. TS-081C052 …………Phillips Pan Head Machine Screw………………….#10-24×3/4” ……………. 2

• 9 ………….. 6295121 ………………Dust Chute …………………………………………………………………………….. 1

• 10 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 2

• 11 ………… TS-0051051 …………Hex Cap Screw …………………………………………5/16”-18×1”…………….. 2

• 12 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 2

• 13 ………… TS-0561021 …………Hex Nut……………………………………………………5/16”-18 ………………… 2

• 14 ………… 6295126 ………………Brush ……………………………………………………………………………………. 1

• 15 ………… TS-081C082 …………Phillips Pan Head Machine Screw………………….#10-24×1-1/2” …………. 2

• 16 ………… 6295128 ………………Lower Back Door …………………………………………………………………….. 1

• 17 ………… TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 9

• 18 ………… TS-1503031 …………Socket Head Cap Screw ……………………………..M6-1.0Px12……………. 9

• 19 ………… 6295131 ………………Power Cord ………………………………………………1Ph………………………. 1
  ……………. 6294805 ………………Power Cord ………………………………………………3Ph………………………. 1

• 20 ………… 6295132 ………………Lower Blade Wheel ………………………………………………………………….. 2

• 21 ………… JWBS20-21 ………….Tire ………………………………………………………………………………………. 2

• 22 ………… 6295134 ………………Hex Nut……………………………………………………3/4”-16(L.H)……………. 2

• 23 ………… TS-0680091 …………Flat Washer………………………………………………3/4” ………………………. 2

• 24 ………… 6295054 ………………Blade ………………………………………………………1”x.026×3 hook ……….. 1

• 25 ………… 6295137 ………………Door Latch …………………………………………………………………………….. 3

• 26 ………… 6295138 ………………Door Catch …………………………………………………………………………….. 3

• 27 ………… 6295139 ………………Phillips Pan Head Machine Screw………………….M4x4 ……………………. 9

• 28 ………… 2013-128……………..Lower Front Door…………………………………………………………………….. 1

• 29 ………… 2013-129……………..Upper Front Door…………………………………………………………………….. 1

• 30 ………… 6295142 ………………Stop Button ……………………………………………………………………………. 1

• 31 ………… 6295143 ………………Start Button ……………………………………………………………………………. 1

• 32 ………… 6295144 ………………Scale ……………………………………………………………………………………. 1

• 33 ………… 6295145 ………………I.D Label ………………………………………………….2HP ……………………… 1

• 33 ………… 6295145A…………….I.D Label ………………………………………………….3HP ……………………… 1

• 34 ………… 6295146 ………………Warning Label ………………………………………………………………………… 1

• 35 ………… 6295147 ………………Name Plate ……………………………………………………………………………. 1

• 37 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 1

• 38 ………… 2013-138……………..Upper Blade Wheel ………………………………………………………………….. 1

• 39 ………… 6295208 ………………Ball Bearing………………………………………………6205 …………………….. 2

• 40 ………… 2013-140……………..Retaining Ring …………………………………………..Ø 52 …………………….. 2

• 41 ………… 2013-141……………..Transformer (not shown) …………………………………………………………… 1

Saw Body Assembly (2415 Band Saw)

• Index No.    Part No.                Description                                                  Size                           Qty

• 1 ………….. 2415-101……………..Body …………………………………………………………………………………….. 1

• 2 ………….. 2415-102N …………..Magnetic Switch ………………………………………..1Ph, 230V ……………… 1
  ……………. 2415-102CSN……….Contactor Switch for 1 Phase (not shown) …………………………………….. 1
  ……………. 2415-102ORN ………Overload Relay for 1 Phase (not shown) ………………………………………. 1
  ……………. 2415-102AN …………Magnetic Switch ………………………………………..3Ph, 230V ……………… 1
  ……………. 2415-102ACSN …….Contactor Switch for 230V 3 Phase (not shown) …………………………….. 1
  ……………. 2415-102AORN …….Overload Relay for 230V 3 Phase (not shown)……………………………….. 1
  ……………. 2415-102B …………..Magnetic Switch ………………………………………..3Ph, 460V ……………… 1
  ……………. 2415-102BCS ……….Contactor Switch for 460V 3 Phase (not shown) …………………………….. 1
  ……………. 2415-102BOR ………Overload Relay for 460V 3 Phase (not shown)……………………………….. 1

• 3 ………….. 2013-103A …………..Switch Plate ………………………………………………………………………….. 1

• 4 ………….. TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 8

• 5 ………….. TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 6

• 6 ………….. TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 2

• 7 ………….. TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 4

• 8 ………….. TS-081C052 …………Phillips Pan Head Machine Screw………………….#10-24×3/4” ……………. 2

• 9 ………….. 6295121 ………………Dust Chute …………………………………………………………………………….. 1

• 10 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 2

• 11 ………… TS-0051051 …………Hex Cap Screw …………………………………………5/16”-18×1”…………….. 2

• 12 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 2

• 13 ………… TS-0561021 …………Hex Nut……………………………………………………5/16”-18 ………………… 2

• 14 ………… 6295126 ………………Brush ……………………………………………………………………………………. 1

• 15 ………… TS-081C082 …………Phillips Pan Head Machine Screw………………….#10-24×1-1/2” …………. 2

• 16 ………… 6294804 ………………Lower Back Door …………………………………………………………………….. 1

• 17 ………… TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 9

• 18 ………… TS-1503031 …………Socket Head Cap Screw ……………………………..M6-1.0Px12……………. 9

• 19 ………… 6295131 ………………Power Cord ………………………………………………1Ph………………………. 1
  ……………. 6294805 ………………Power Cord ………………………………………………3Ph………………………. 1

• 20 ………… 6294806 ………………Lower Blade Wheel ………………………………………………………………….. 2

• 21 ………… 6294807 ………………Tire ………………………………………………………………………………………. 2

• 22 ………… 6295134 ………………Hex Nut……………………………………………………3/4”-16(L.H)……………. 2

• 23 ………… TS-0680091 …………Flat Washer………………………………………………3/4” ………………………. 2

• 24 ………… 6295061 ………………Blade ………………………………………………………1”x.026×3 hook ……….. 1

• 25 ………… 6295137 ………………Door Latch …………………………………………………………………………….. 3

• 26 ………… 6295138 ………………Door Catch …………………………………………………………………………….. 3

• 27 ………… 6295139 ………………Phillips Pan Head Machine Screw………………….M4x4 ……………………. 9

• 28 ………… 2415-128……………..Lower Front Door…………………………………………………………………….. 1

• 29 ………… 2415-129……………..Upper Front Door…………………………………………………………………….. 1

• 30 ………… 6295142 ………………Stop Button ……………………………………………………………………………. 1

• 31 ………… 6295143 ………………Start Button ……………………………………………………………………………. 1

• 32 ………… 6294810 ………………Scale ……………………………………………………………………………………. 1

• 33 ………… 6294811 ………………I.D Label ………………………………………………….3HP ……………………… 1

• 33 ………… 6294811A…………….I.D Label ………………………………………………….5HP ……………………… 1

• 34 ………… 6295146 ………………Warning Label ………………………………………………………………………… 1

• 35 ………… 6295147 ………………Name Plate ……………………………………………………………………………. 1

• 37 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 1

• 38 ………… 2415-138……………..Upper Blade Wheel ………………………………………………………………….. 1

• 39 ………… 6295208 ………………Ball Bearing………………………………………………6205 …………………….. 2

• 40 ………… 2013-140……………..Retaining Ring …………………………………………..Ø 52 …………………….. 2

• 41 ………… 2013-141……………..Transformer (not shown) …………………………………………………………… 1

Saw Body Assembly (2013 and 2415)

Parts List: Table Assembly (2013 Band Saw)

• Index No.    Part No.          Description                                                          Size                           Qty

• 1 ………….. 2013-201……………..Carriage Bolt …………………………………………….1/2”-12×9” ……………… 1

• 2 ………….. 6295149 ………………Trunnion (Left Side) …………………………………………………………………. 1

• 3 ………….. 2013-203……………..Table Bracket …………………………………………………………………………. 1

• 4 ………….. TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 8

• 5 ………….. TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 8

• 6 ………….. TS-0060061 …………Hex Cap Screw …………………………………………3/8”-16×1-1/4”…………. 8

• 7 ………….. 6295154 ………………Name Plate ……………………………………………………………………………. 1

• 8 ………….. 6295155 ………………Pointer ………………………………………………………………………………….. 1

• 9 ………….. TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 1

• 10 ………… TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 1

• 11 ………… 6295158 ………………Locking Handle……………………………………………………………………….. 1

• 12 ………… TS-0680061 …………Flat Washer………………………………………………1/2” ………………………. 1

• 13 ………… 2013-213……………..Angle Scale Plate ……………………………………………………………………. 1
  ……………. 6295328 ………………Miter Gauge Assembly (Items 14 thru 24) …………………………………….. 1

• 14 ………… 6295161 ………………Pin ……………………………………………………………………………………….. 1

• 15 ………… 6295162 ………………Flat Head Screw ………………………………………..1/4” ………………………. 1

• 16 ………… 6295163 ………………Guard Disc …………………………………………………………………………….. 1

• 17 ………… TS-1533062 …………Phillips Pan Head Machine Screw………………….M5-0.8Px20……………. 3

• 18 ………… TS-1540031 …………Nut …………………………………………………………M5 ……………………….. 3

• 19 ………… 6295166 ………………Knob …………………………………………………………………………………….. 1

• 20 ………… 6295167 ………………Miter Gauge Body ……………………………………………………………………. 1

• 21 ………… 6295168 ………………Pin ……………………………………………………………………………………….. 1

• 22 ………… 6295169 ………………Pointer ………………………………………………………………………………….. 1

• 23 ………… TS-1521011 …………Socket Set Screw ………………………………………M4x4 ……………………. 1

• 24 ………… 6295171 ………………Stop Block……………………………………………………………………………… 1

• 25 ………… 6295172 ………………Work Table…………………………………………………………………………….. 1

• 26 ………… TS-0050021 …………Hex Cap Screw …………………………………………1/4”-20×5/8”……………. 9
  ……………. 6295329 ………………Fence Assembly (Items 7,27,28,32,33,34,39 thru 52) ……………………… 1

• 27 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” …………………….. 10

• 28 ………… TS-0680021 …………Flat Washer………………………………………………1/4” …………………….. 10

• 29 ………… 6295176 ………………Rear Rail ……………………………………………………………………………….. 1

• 30 ………… 6295177 ………………Table Insert ……………………………………………………………………………. 1

• 31 ………… 6295178 ………………Spring Pin ………………………………………………..Ø3×10 …………………… 2

• 32 ………… TS-0561011 …………Hex Nut……………………………………………………1/4”-20 ………………….. 2

• 33 ………… 6295180 ………………Rear Hook……………………………………………………………………………… 1

• 34 ………… 6295181 ………………Sliding Pad …………………………………………………………………………….. 1

• 35 ………… TS-0570031 …………Hex Nut……………………………………………………3/8”-16 ………………….. 1

• 36 ………… TS-0060171 …………Hex Cap Screw …………………………………………3/8”-16×4” ……………… 1

• 37 ………… 6295184 ………………Scale ……………………………………………………………………………………. 1

• 38 ………… 6295185 ………………Guide Rail ……………………………………………………………………………… 1

• 39 ………… 6295186 ………………Fence …………………………………………………………………………………… 1

• 40 ………… TS-0081031 …………Hex Cap Screw …………………………………………5/16”-18×3/4” ………….. 4

• 41 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 4

• 42 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4

• 43 ………… TS-0810012 …………Screw ……………………………………………………..#10-24×1/4” ……………. 1

• 44 ………… TS-0733031 …………External Tooth Lock Washer…………………………#10 ………………………. 1

• 45 ………… 6295193 ………………Pointer ………………………………………………………………………………….. 1

• 46 ………… 6295194 ………………Fence Body ……………………………………………………………………………. 1

• 47 ………… 6295195 ………………Knob …………………………………………………………………………………….. 1

• 48 ………… 6295196 ………………Lock Handle …………………………………………………………………………… 1

• 49 ………… 6295197 ………………Lock Plate ……………………………………………………………………………… 1

• 50 ………… 6295198 ………………Pad………………………………………………………………………………………. 2

• 51 ………… 6295199 ………………Pin ……………………………………………………………………………………….. 1

• 52 ………… 6295200 ………………Pin ……………………………………………………………………………………….. 1

• 53 ………… 2013-253……………..Bushing…………………………………………………………………………………. 1

• 54 ………… TS-0051061 …………Hex Cap Screw …………………………………………5/16”-18×1-1/4” ……….. 2

• 56 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 1

• 57 ………… TS-0270061 …………Socket Set Screw ………………………………………5/16”-18×5/8” ………….. 4

• 58 ………… 6294841 ………………Front Rail ………………………………………………………………………………. 1

• 59 ………… 2013-259……………..Trunnion (Right Side) ……………………………………………………………….. 1

• 60 ………… 2013-260……………..Shaft …………………………………………………………………………………….. 1

• 61 ………… 2013-261……………..C-Ring …………………………………………………….S-17……………………… 1

• 62 ………… 2013-262……………..Gear …………………………………………………………………………………….. 1

• 63 ………… 2013-263……………..Worm Gear ……………………………………………………………………………. 1

• 64 ………… TS-081F032 …………Phillips Pan Head Machine Screw………………….1/4”-20X1/2” …………… 2

• 65 ………… 2013-265……………..Worm Gear Cap ……………………………………………………………………… 1

• 66 ………… BB-6002 ………………Ball Bearing………………………………………………6002 …………………….. 1

• 67 ………… 2013-267……………..C-Ring …………………………………………………….S-15……………………… 1

• 68 ………… 2013-268……………..Worm Shaft ……………………………………………………………………………. 1

• 69 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18X1/2” …………. 2

• 70 ………… 2013-270……………..Bevel Gear …………………………………………………………………………….. 2

• 71 ………… 2013-271……………..Bushing…………………………………………………………………………………. 1

• 72 ………… TS-0267021 …………Socket Set Screw ………………………………………1/4”-20×1/4”……………. 6

• 73 ………… 2013-273……………..Key …………………………………………………………5x5x12 ………………….. 1

• 74 ………… 2013-274……………..C-Ring …………………………………………………….S-13……………………… 1

• 75 ………… 2012-275……………..Bushing…………………………………………………………………………………. 2

• 76 ………… 2013-276……………..Handwheel Assembly……………………………………………………………….. 1

• 77 ………… 2013-277……………..Shaft …………………………………………………………………………………….. 1

• 78 ………… TS-0246031 …………Flat Head Socket Screw ………………………………5/16”-18×3/4” ………….. 6

• 79 ………… TS-0255031 …………Button Head Socket Screw …………………………..5/16”-18×5/8” ………….. 4

• 80 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 4

• 81 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4

• 82 ………… 2013-282……………..Gear Bracket ………………………………………………………………………….. 1

• 83 ………… 2013-283……………..Handle ………………………………………………………………………………….. 1

• 84 ………… 2013-284……………..Key …………………………………………………………3x3x8 ……………………. 2

• 85 ………… 2013-285……………..End Cover ……………………………………………………………………………… 2

Parts List: Table Assembly (2415 Band Saw)

• Index No.     Part No.                  Description                                                              Size                             Qty

• 1 ………….. 2013-201……………..Carriage Bolt …………………………………………….1/2-12×9”……………….. 1

• 2 ………….. 6295149 ………………Trunnion (Left Side) …………………………………………………………………. 1

• 3 ………….. 2013-203……………..Table Bracket …………………………………………………………………………. 1

• 4 ………….. TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 8

• 5 ………….. TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 8

• 6 ………….. TS-0060061 …………Hex Cap Screw …………………………………………3/8”-16×1-1/4”…………. 8

• 7 ………….. 6295154 ………………Name Plate ……………………………………………………………………………. 1

• 8 ………….. 6295155 ………………Pointer ………………………………………………………………………………….. 1

• 9 ………….. TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 1

• 10 ………… TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 1

• 11 ………… 6295158 ………………Locking Handle……………………………………………………………………….. 1

• 12 ………… TS-0680061 …………Flat Washer………………………………………………1/2” ………………………. 1

• 13 ………… 2013-213……………..Angle Scale Plate ……………………………………………………………………. 1
  ……………. 6295328 ………………Miter Gauge Assembly (Items 14 thru 24) …………………………………….. 1

• 14 ………… 6295161 ………………Pin ……………………………………………………………………………………….. 1

• 15 ………… 6295162 ………………Flat Head Screw ………………………………………..1/4” ………………………. 1

• 16 ………… 6295163 ………………Guard Disc …………………………………………………………………………….. 1

• 17 ………… TS-1533062 …………Phillips Pan Head Machine Screw………………….M5x20…………………… 3

• 18 ………… TS-1540031 …………Nut …………………………………………………………M5 ……………………….. 3

• 19 ………… 6295166 ………………Knob …………………………………………………………………………………….. 1

• 20 ………… 6295167 ………………Miter Gauge Body ……………………………………………………………………. 1

• 21 ………… 6295168 ………………Pin ……………………………………………………………………………………….. 1

• 22 ………… 6295169 ………………Pointer ………………………………………………………………………………….. 1

• 23 ………… TS-1521011 …………Socket Set Screw ………………………………………M4x4 ……………………. 1

• 24 ………… 6295171 ………………Stop Block……………………………………………………………………………… 1

• 25 ………… 6294836 ………………Work Table…………………………………………………………………………….. 1

• 26 ………… TS-0050021 …………Hex Cap Screw …………………………………………1/4”-20×5/8”……………. 9
  ……………. 6294842 ………………Fence Assembly (Items7,27,28,32,33,34,39 thru 52) ………………………. 1

• 27 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” …………………….. 10

• 28 ………… TS-0680021 …………Flat Washer………………………………………………1/4” …………………….. 10

• 29 ………… 6294837 ………………Rear Rail ……………………………………………………………………………….. 1

• 30 ………… 6295177 ………………Table Insert ……………………………………………………………………………. 1

• 31 ………… 6295178 ………………Spring Pin ………………………………………………..Ø3×10 …………………… 2

• 32 ………… TS-0561011 …………Hex Nut……………………………………………………1/4”-20 ………………….. 2

• 33 ………… 6295180 ………………Rear Hook……………………………………………………………………………… 1

• 34 ………… 6295181 ………………Sliding Pad …………………………………………………………………………….. 1

• 35 ………… TS-0570031 …………Hex Nut……………………………………………………3/8”-16 ………………….. 1

• 36 ………… TS-0060171 …………Hex Cap Screw …………………………………………3/8”-16×4” ……………… 1

• 37 ………… 6294838 ………………Scale ……………………………………………………………………………………. 1

• 38 ………… 6294839 ………………Guide Rail ……………………………………………………………………………… 1

• 39 ………… 6294840 ………………Fence …………………………………………………………………………………… 1

• 40 ………… TS-0081031 …………Hex Cap Screw …………………………………………5/16”-18×3/4” ………….. 4

• 41 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 4

• 42 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4

• 43 ………… TS-0810012 …………Screw ……………………………………………………..#10-24×1/4” ……………. 1

• 44 ………… TS-0733031 …………External Tooth Lock Washer…………………………#10 ………………………. 1

• 45 ………… 6295193 ………………Pointer ………………………………………………………………………………….. 1

• 46 ………… 6295194 ………………Fence Body ……………………………………………………………………………. 1

• 47 ………… 6295195 ………………Knob …………………………………………………………………………………….. 1

• 48 ………… 6295196 ………………Lock Handle …………………………………………………………………………… 1

• 49 ………… 6295197 ………………Lock Plate ……………………………………………………………………………… 1

• 50 ………… 6295198 ………………Pad………………………………………………………………………………………. 2

• 51 ………… 6295199 ………………Pin ……………………………………………………………………………………….. 1

• 52 ………… 6295200 ………………Pin ……………………………………………………………………………………….. 1

• 53 ………… 2013-253……………..Bushing…………………………………………………………………………………. 1

• 54 ………… TS-0051061 …………Hex Cap Screw …………………………………………5/16”-18×1-1/4” ……….. 2

• 56 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 1

• 57 ………… TS-0270061 …………Socket Set Screw ………………………………………5/16”-18×5/8” ………….. 4

• 58 ………… 6294841 ………………Front Rail ………………………………………………………………………………. 1

• 59 ………… 2013-259……………..Trunnion (Right Side) ……………………………………………………………….. 1

• 60 ………… 2013-260……………..Shaft …………………………………………………………………………………….. 1

• 61 ………… 2013-261……………..C-Ring …………………………………………………….S-17……………………… 1

• 62 ………… 2013-262……………..Gear …………………………………………………………………………………….. 1

• 63 ………… 2013-263……………..Worm Gear ……………………………………………………………………………. 1

• 64 ………… TS-081F032 …………Phillips Pan Head Machine Screw………………….1/4”-20X1/2” …………… 2

• 65 ………… 2013-265……………..Worm Gear Cap ……………………………………………………………………… 1

• 66 ………… BB-6002 ………………Ball Bearing………………………………………………6002 …………………….. 1

• 67 ………… 2013-267……………..C-Ring …………………………………………………….S-15……………………… 1

• 68 ………… 2013-268……………..Worm Shaft ……………………………………………………………………………. 1

• 69 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18X1/2” …………. 2

• 70 ………… 2013-270……………..Bevel Gear …………………………………………………………………………….. 2

• 71 ………… 2013-271……………..Bushing…………………………………………………………………………………. 1

• 72 ………… TS-0267021 …………Socket Set Screw ………………………………………1/4”-20×1/4”……………. 6

• 73 ………… 2013-273……………..Key …………………………………………………………5x5x12 ………………….. 1

• 74 ………… 2013-274……………..C-Ring …………………………………………………….S-13……………………… 1

• 75 ………… 2012-275……………..Bushing…………………………………………………………………………………. 2

• 76 ………… 2013-276……………..Handwheel Assembly……………………………………………………………….. 1

• 77 ………… 2013-277……………..Shaft …………………………………………………………………………………….. 1

• 78 ………… TS-0246031 …………Flat Head Socket Screw ………………………………5/16”-18×3/4” ………….. 6

• 79 ………… TS-0255031 …………Button Head Socket Screw …………………………..5/16”-18×5/8” ………….. 4

• 80 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 4

• 81 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4

• 82 ………… 2013-282……………..Gear Bracket ………………………………………………………………………….. 1

• 83 ………… 2013-283……………..Handle ………………………………………………………………………………….. 1

• 84 ………… 2013-284……………..Key …………………………………………………………3x3x8 ……………………. 2

• 85 ………… 2013-285……………..End Cover ……………………………………………………………………………… 2

Table Assembly (2013 and 2415)

Parts List: Upper Wheel Base Assembly (2013 Band Saw)

• Index No.   Part No.                     Description                                                 Size                                                          Qty

• 1 ………….. 2013-301……………..Upper Wheel Shaft (for 2013, serial #05032013437 and higher) ………………. 1
  ……………. 6295889 ………………Upper Wheel Shaft (for 2013-1, serial #01062013080 to 05032013437) ………..1 (for 2013-3, serial #01062013090 to 05032013437)

• 2 ………….. TS-0680091 …………Flat Washer………………………………………………3/4” ………………………. 1

• 4 ………….. TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 8

• 5 ………….. 2013-305……………..Upper Wheel Shaft Bracket ……………………………………………………….. 1

• 6 ………….. 6295890 ………………Lock Nut ………………………………………………….3/4”-16 UNF …………… 1

• 7 ………….. TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 5

• 8 ………….. 6295213 ………………C-Ring …………………………………………………….S-20……………………… 2

• 9 ………….. 6295214 ………………Lever Shaft…………………………………………………………………………….. 1

• 10 ………… 6295215 ………………Upper Adjustment Bracket …………………………………………………………. 1

• 11 ………… 6295891 ………………Upper Wheel Guide Bracket ………………………………………………………. 1

• 12 ………… 6295217 ………………Adjustment Bracket ………………………………………………………………….. 1

• 13 ………… TS-0640091 …………Nylon Lock Hex Nut ……………………………………3/8”-16 ………………….. 1

• 14 ………… 6295219 ………………Lock Knob ……………………………………………………………………………… 1

• 15 ………… 6295220 ………………Adjustment Screw ……………………………………………………………………. 1

• 16 ………… 6295221 ………………Elevator Bracket ……………………………………………………………………… 1

• 17 ………… 6295222 ………………Spring …………………………………………………………………………………… 2

• 18 ………… 6295223 ………………Guide Bar………………………………………………………………………………. 2

• 19 ………… TS-0810012 …………Screw ……………………………………………………..#10-24×1/4” ……………. 1

• 20 ………… 6295225 ………………Bracket …………………………………………………………………………………. 1

• 21 ………… 6295226 ………………Pointer ………………………………………………………………………………….. 1

• 22 ………… TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 3

• 23 ………… 6295227 ………………Upper Wheel Bracket Base ……………………………………………………….. 1

• 24 ………… 6295228 ………………Bracket Shaft………………………………………………………………………….. 2

• 25 ………… 6295229 ………………Handwheel …………………………………………………………………………….. 1

• 26 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 2

• 27 ………… TS-0640081 …………Nylon Insert Lock Nut ………………………………….5/16”-18 ………………… 2

• 28 ………… TS-0208121 …………Socket Head Cap Screw ……………………………..5/16”-18 x 2-1/2” ……… 2

• 29 ………… TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 4

• 30 ………… TS-0060081 …………Hex Cap Screw …………………………………………3/8”-16×1-3/4”…………. 6

• 31 ………… 2013-331……………..Work Lamp……………………………………………….115V …………………….. 1

• 32 ………… 6295236 ………………Scale (Blade tension) ……………………………………………………………….. 1

• 33 ………… 2013-333……………..Bushing…………………………………………………………………………………. 3

• 34 ………… TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 2

Parts List: Upper Wheel Base Assembly (2415 Band Saw)

• Index No. Part No.               Description                                         Size                                                     Qty

• 1 ………….. 2013-301……………..Upper Wheel Shaft (for 2415, serial #05022415369 and higher) ………………. 1
  ……………. 6295889 ………………Upper Wheel Shaft (for 2415-1, serial #01062415017 to 05022415368) ………..1
  (for 2415-3, serial #01062415011 to 05022415368)

• 2 ………….. TS-0680091 …………Flat Washer………………………………………………3/4” ………………………. 1

• 4 ………….. TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 8

• 5 ………….. 2013-305……………..Upper Wheel Shaft Bracket ……………………………………………………….. 1

• 6 ………….. 6295890 ………………Lock Nut ………………………………………………….3/4”-16 UNF …………… 1

• 7 ………….. TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 5

• 8 ………….. 6295213 ………………C-Ring …………………………………………………….S-20……………………… 2

• 9 ………….. 6295214 ………………Lever Shaft…………………………………………………………………………….. 1

• 10 ………… 6295215 ………………Upper Adjustment Bracket …………………………………………………………. 1

• 11 ………… 6295891 ………………Upper Wheel Guide Bracket ………………………………………………………. 1

• 12 ………… 6295217 ………………Adjustment Bracket ………………………………………………………………….. 1

• 13 ………… TS-0640091 …………Nylon Lock Hex Nut ……………………………………3/8”-16 ………………….. 1

• 14 ………… 6295219 ………………Lock Knob ……………………………………………………………………………… 1

• 15 ………… 6294812 ………………Adjustment Screw ……………………………………………………………………. 1

• 16 ………… 6295221 ………………Elevator Bracket ……………………………………………………………………… 1

• 17 ………… 6294813 ………………Spring …………………………………………………………………………………… 2

• 18 ………… 6294814 ………………Guide Bar………………………………………………………………………………. 2

• 19 ………… TS-0810012 …………Screw ……………………………………………………..#10-24×1/4” ……………. 1

• 20 ………… 6294815 ………………Bracket …………………………………………………………………………………. 1

• 21 ………… 6295226 ………………Pointer ………………………………………………………………………………….. 1

• 22 ………… TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 3

• 23 ………… 6294816 ………………Upper Wheel Bracket Base ……………………………………………………….. 1

• 24 ………… 6295228 ………………Bracket Shaft………………………………………………………………………….. 2

• 25 ………… 6295229 ………………Handwheel …………………………………………………………………………….. 1

• 26 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 2

• 27 ………… TS-0640081 …………Nylon Insert Lock Nut ………………………………….5/16”-18 ………………… 2

• 28 ………… TS-0208121 …………Socket Head Cap Screw ……………………………..5/16”-18 x 2-1/2” ……… 2

• 29 ………… TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 4

• 30 ………… TS-0060081 …………Hex Cap Screw …………………………………………3/8”-16×1-3/4”…………. 6

• 31 ………… 2013-331……………..Work Lamp……………………………………………….115V …………………….. 1

• 32 ………… 6294818 ………………Scale (Blade tension) ……………………………………………………………….. 1

• 33 ………… 2013-333……………..Bushing…………………………………………………………………………………. 3

• 34 ………… TS-081C022 …………Phillips Pan Head Machine Screw………………….#10-24×3/8” ……………. 2

Upper Wheel Base Assembly (2013 and 2415)

Parts List: Lower Wheel Base Assembly (2013 Band Saw)

• Index No. Part No.                Description                                                         Size                          Qty

• 1 ………….. TS-0207061 …………Socket Head Cap Screw ……………………………..1/4”-20×1” ……………… 1

• 2 ………….. TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 5

• 3 ………….. 6295238 ………………Brake Pedal …………………………………………………………………………… 1

• 4 ………….. 6295239 ………………Brake Bracket…………………………………………………………………………. 2

• 5 ………….. TS-0561011 …………Hex Nut……………………………………………………1/4”-20 ………………….. 9

• 6 ………….. 6295241 ………………Spring …………………………………………………………………………………… 1

• 7 ………….. 6295242 ………………Brake Switch ………………………………………………………………………….. 1

• 8 ………….. TS-0640091 …………Nylon Insert Lock Nut ………………………………….3/8”-16 ………………….. 1

• 9 ………….. 6295243 ………………Brake Wheel…………………………………………………………………………… 1

• 10 ………… 6295244 ………………Brake Belt ……………………………………………………………………………… 1

• 11 ………… 6295245 ………………Brake Band ……………………………………………………………………………. 1

• 12 ………… TS-0050031 …………Hex Cap Screw …………………………………………1/4”-20×3/4”……………. 4

• 13 ………… 6295247 ………………Key …………………………………………………………7x7x25 ………………….. 2

• 14 ………… 6295248 ………………Shaft …………………………………………………………………………………….. 1

• 15 ………… 6295249 ………………Ball Bearing………………………………………………6206 …………………….. 2

• 16 ………… 6295250 ………………Bearing Base………………………………………………………………………….. 1

• 17 ………… 6295251 ………………Adjusting Screw ………………………………………………………………………. 4

• 18 ………… TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 4

• 19 ………… TS-0060091 …………Hex Cap Screw …………………………………………3/8”-16×2” ……………… 5

• 20 ………… 6295253 ………………Hex Nut……………………………………………………M28 ……………………… 1

• 21 ………… 6295254A…………….Spindle Pulley (serial # 08102013704 and higher)……………………………….. 1
  ……………. 6295254 ………………Spindle Pulley (serial # 08102013703 and lower) ………………………………… 1

• 22 ………… TS-0267041 …………Socket Set Screw ………………………………………1/4”-20×3/8”……………. 2

• 23 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………… 10

• 24 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 6

• 25 ………… TS-0561021 …………Hex Nut……………………………………………………5/16”-18 ………………… 5

• 26 ………… 6295256 ………………Motor ………………………………………………………2HP, 1Ph ………………. 1
  ……………. 2013-426SC …………Starting Capacitor ………………………………………500MFD, 125VAC……. 1
  ……………. 2013-426RC …………Running Capacitor ……………………………………..30μF, 300VAC………… 1
  ……………. 6295331 ………………Motor ………………………………………………………3HP, 3Ph ………………. 1

• 27 ………… TS-0208081 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/2” ……….. 4

• 28 ………… 6295258 ………………Core …………………………………………………………………………………….. 1

• 29 ………… 6295259 ………………Core Piece …………………………………………………………………………….. 4

• 30 ………… 6295260 ………………Fan Cover ……………………………………………………………………………… 1

• 31 ………… 6295261 ………………Hose Connector ……………………………………………………………………… 1

• 32 ………… 6295262 ………………Air Input Valve ………………………………………………………………………… 1

• 33 ………… TS-0207041 …………Socket Head Cap Screw ……………………………..1/4”-20×3/4”……………. 3

• 34 ………… 6295264A…………….Motor Pulley (serial # 08102013704 and higher) ……. ……………………………. 1
  ……………. 6295264 ………………Motor Pulley (serial # 08102013703 and lower) ………………………………….. 1

• 35 ………… 6295265 ………………Belt …………………………………………………………501J …………………….. 1

• 36 ………… 6295266 ………………Hose …………………………………………………………………………………….. 1

• 37 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 4

• 38 ………… 6295268 ………………Key …………………………………………………………7x7x40 ………………….. 2

• 39 ………… 6295269 ………………Motor Cord ……………………………………………….1Ph………………………. 1
  ……………. 6294828 ………………Motor Cord ……………………………………………….3Ph………………………. 1

• 41 ………… TS-0060091 …………Hex Cap Screw …………………………………………3/8”-16×2” ……………… 1

• 42 ………… 6295272 ………………Plate …………………………………………………………………………………….. 2

• 43 ………… TS-2284302 …………Phillips Pan Head Machine Screw………………….M4x30…………………… 2

• 44 ………… TS-1540021 …………Hex Nut……………………………………………………M4 ……………………….. 2

• 45 ………… 6294830 ………………Motor Plate…………………………………………………………………………….. 1

• 46 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 4

• 47 ………… 6294832 ………………Belt Tension Bracket ………………………………………………………………… 1

• 48 ………… TS-0051021 …………Hex Cap Screw …………………………………………5/16”-18×5/8” ………….. 2

• 49 ………… TS-0051111 …………Hex Cap Screw …………………………………………5/16”-18×2-1/2” ……….. 1

• 50 ………… TS-0640071 …………Nylon Insert Lock Nut ………………………………….1/4”-20 ………………….. 2

• 51 ………… TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 2

• 52 ………… TS-0561031 …………Hex Nut……………………………………………………3/8”-16 ………………….. 4

• 53 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” ………………………. 4

• 54 ………… TS-081C032 …………Screw ……………………………………………………..#10-24×1/2” ……………. 4

• 55 ………… TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 4

• 56 ………… TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 4

• 57 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 4

Parts List: Lower Wheel Base Assembly (2415 Band Saw)

• Index No. Part No.                 Description                                                       Size                          Qty

• 1 ………….. TS-0207061 …………Socket Head Cap Screw ……………………………..1/4”-20×1” ……………… 1

• 2 ………….. TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 5

• 3 ………….. 6294819 ………………Brake Pedal …………………………………………………………………………… 1

• 4 ………….. 6295239 ………………Brake Bracket…………………………………………………………………………. 2

• 5 ………….. TS-0561011 …………Hex Nut……………………………………………………1/4”-20 ………………….. 9

• 6 ………….. 6295241 ………………Spring …………………………………………………………………………………… 1

• 7 ………….. 6295242 ………………Brake Switch ………………………………………………………………………….. 1

• 8 ………….. TS-0640091 …………Nylon Insert Lock Nut ………………………………….3/8”-16 ………………….. 1

• 9 ………….. 6295243A…………….Brake Wheel…………………………………………………………………………… 1

• 10 ………… 6294820 ………………Brake Belt ……………………………………………………………………………… 1

• 11 ………… 6294821 ………………Brake Band ……………………………………………………………………………. 1

• 12 ………… TS-0050031 …………Hex Cap Screw …………………………………………1/4”-20×3/4”……………. 4

• 13 ………… 6295247 ………………Key …………………………………………………………7x7x25 ………………….. 2

• 14 ………… 6295248A…………….Shaft …………………………………………………………………………………….. 1

• 15 ………… 6295249 ………………Ball Bearing………………………………………………6206 …………………….. 2

• 16 ………… 6295250 ………………Bearing Base………………………………………………………………………….. 1

• 17 ………… 6295251 ………………Adjusting Screw ………………………………………………………………………. 4

• 18 ………… TS-0720091 …………Lock Washer …………………………………………….3/8” ………………………. 4

• 19 ………… TS-0060091 …………Hex Cap Screw …………………………………………3/8”-16×2” ……………… 5

• 20 ………… 6295253 ………………Hex Nut……………………………………………………M28 ……………………… 1

• 21 ………… 6294822A…………….Spindle Pulley (serial # 08082415835 and higher)……………………………….. 1
  ……………. 6294822 ………………Spindle Pulley (serial # 08082415834 and lower) ….. ……………………………. 1

• 22 ………… TS-0267041 …………Socket Set Screw ………………………………………1/4”-20×3/8”……………. 2

• 23 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………… 10

• 24 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 6

• 25 ………… TS-0561021 …………Hex Nut……………………………………………………5/16”-18 ………………… 5

• 26 ………… 2415-426……………..Motor ………………………………………………………3HP, 1Ph ………………. 1
  ……………. 2013-426SC …………Starting Capacitor ………………………………………500MFD, 125VAC……. 1
  ……………. 2415-426RC …………Running Capacitor ……………………………………..40μF, 250VAC………… 1
  ……………. 2415-426A …………..Motor ………………………………………………………5HP, 3Ph ………………. 1

• 27 ………… TS-0208081 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/2” ……….. 4

• 28 ………… 6295258 ………………Core …………………………………………………………………………………….. 1

• 29 ………… 6295259 ………………Core Piece …………………………………………………………………………….. 4

• 30 ………… 6295260 ………………Fan Cover ……………………………………………………………………………… 1

• 31 ………… 6295261 ………………Hose Connector ……………………………………………………………………… 1

• 32 ………… 6295262 ………………Air Input Valve ………………………………………………………………………… 1

• 33 ………… TS-0207041 …………Socket Head Cap Screw ……………………………..1/4”-20×3/4”……………. 3

• 34 ………… 6294825A…………….Motor Pulley (serial # 08082415835 and higher) …………………………………. 1
  ……………. 6294825 ………………Motor Pulley (serial # 08082415834 and lower) ………………………………….. 1

• 35 ………… 6294826 ………………Belt …………………………………………………………540J …………………….. 1

• 36 ………… 6294827 ………………Hose …………………………………………………………………………………….. 1

• 37 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 4

• 38 ………… 6295268 ………………Key …………………………………………………………7x7x40 ………………….. 2

• 39 ………… 6295269 ………………Motor Cord ……………………………………………….1Ph………………………. 1
  ……………. 6294828 ………………Motor Cord ……………………………………………….3Ph………………………. 1

• 41 ………… TS-0060091 …………Hex Cap Screw …………………………………………3/8”-16×2” ……………… 1

• 42 ………… 6295272 ………………Plate …………………………………………………………………………………….. 2

• 43 ………… TS-2284302 …………Phillips Pan Head Machine Screw………………….M4x30…………………… 2

• 44 ………… TS-1540021 …………Hex Nut……………………………………………………M4 ……………………….. 2

• 45 ………… 6294830 ………………Motor Plate…………………………………………………………………………….. 1

• 46 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 4

• 47 ………… 6294832 ………………Belt Tension Bracket ………………………………………………………………… 1

• 48 ………… TS-0051021 …………Hex Cap Screw …………………………………………5/16”-18×5/8” ………….. 2

• 49 ………… TS-0051111 …………Hex Cap Screw …………………………………………5/16”-18×2-1/2” ……….. 1

• 50 ………… TS-0640071 …………Nylon Lock Hex Nut ……………………………………1/4”-20 ………………….. 2

• 51 ………… TS-0680041 …………Flat Washer………………………………………………3/8” ………………………. 2

• 52 ………… TS-0561031 …………Hex Nut……………………………………………………3/8”-16 ………………….. 4

• 53 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” ………………………. 4

• 54 ………… TS-081C032 …………Screw ……………………………………………………..#10-24×1/2” ……………. 4

• 55 ………… TS-0720051 …………Lock Washer …………………………………………….#10 ………………………. 4

• 56 ………… TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 4

• 57 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 4

Lower Wheel Base Assembly (2013 and 2415)

Parts List: Guide Bracket Assembly (2013 Band Saw)

• Index No. Part No.                 Description                                                       Size                      Qty
• 1 ………….. 6295275 ………………Guide Bar Case Bracket……………………………………………………………. 1
• 2 ………….. 6295276 ………………Cover ……………………………………………………………………………………. 1
• 3 ………….. TS-0081031 …………Hex Cap Screw …………………………………………5/16”-18×3/4” ………….. 4
• 4 ………….. TS-0050011 …………Hex Cap Screw …………………………………………1/4”-20×1/2”……………. 1
• 5 ………….. 6295278 ………………Pointer ………………………………………………………………………………….. 1
• 6 ………….. 6295279 ………………Guide Bar………………………………………………………………………………. 1
• 7 ………….. 6295280 ………………Worm ……………………………………………………………………………………. 1
• 8 ………….. 6295281 ………………Miniature Ball Bearing …………………………………609 ………………………. 1
• 9 ………….. 6295282 ………………C-Ring …………………………………………………….S-12……………………… 2
• 10 ………… 6295283 ………………Gear …………………………………………………………………………………….. 1
• 11 ………… TS-0208071 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/4” ……….. 6
• 12 ………… 6295285 ………………Gear Base……………………………………………………………………………… 1
• 13 ………… 6295286 ………………Set Block……………………………………………………………………………….. 1
• 14 ………… 6295287 ………………Thumb Screw ……………………………………………1/4”-20×1/4”……………. 1
• 15 ………… 6295288 ………………Inner Blade Guard …………………………………………………………………… 1
• 16 ………… 6295289 ………………Blade Guard …………………………………………………………………………… 1
• 17 ………… TS-0050021 …………Hex Cap Screw …………………………………………1/4”-20×5/8”……………. 4
• 18 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” ………………………. 4
• 19 ………… TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 7
• 20 ………… 6295291 ………………Guide Bar Bracket …………………………………………………………………… 1
• 21 ………… TS-0270131 …………Socket Set Screw ………………………………………5/16”-18×2”…………….. 1
• 22 ………… 6295293 ………………Locking Handle………………………………………….1/4”x3/4” ……………….. 1
• 23 ………… TS-1521011 …………Socket Set Screw ………………………………………M4x4 ……………………. 4
• 24 ………… 6295294 ………………Knob …………………………………………………………………………………….. 2
• 25 ………… TS-0267021 …………Socket Set Screw ………………………………………1/4”-20×1/4”……………. 6
• 26 ………… 6295296 ………………Lever Shaft…………………………………………………………………………….. 1
• 27 ………… 6295297 ………………Hand Nut……………………………………………………………………………….. 2
• 28 ………… 6295298 ………………Bolt ………………………………………………………………………………………. 1
• 29 ………… 6295299 ………………Support Bearing Bracket (L) ………………………………………………………. 1
• 30 ………… 6295300 ………………Adjustment Bolt ………………………………………………………………………. 1
• 31 ………… TS-0207041 …………Socket Head Cap Screw ……………………………..1/4”-20×3/4”……………. 2
• 32 ………… 6295302 ………………Support Bearing Shaft ………………………………………………………………. 1
• 33 ………… 6295303 ………………Spacer ………………………………………………………………………………….. 2
• 34 ………… 6295304 ………………C-Ring …………………………………………………….S-15……………………… 4
• 35 ………… 6295305 ………………Ball Bearing………………………………………………6202 …………………….. 5
• 36 ………… 6295306 ………………Shaft …………………………………………………………………………………….. 2
• 37 ………… 6295307 ………………Knob ……………………………………………………….3/8”-16×2” ……………… 1
• 38 ………… TS-0208071 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/4” ……….. 4
• 39 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 6
• 40 ………… 6295308 ………………Ball Bearing……………………………………………………………………………. 1
• 41 ………… 6295309 ………………Bracket …………………………………………………………………………………. 1
• 42 ………… TS-0208041 …………Socket Head Cap Screw ……………………………..5/16”-18×3/4” ………….. 2
• 43 ………… 6295311 ………………Plastic Washer ……………………………………………………………………….. 1
• 44 ………… 6295312 ………………Handwheel …………………………………………………………………………….. 1
• 45 ………… 6295313 ………………Handle ………………………………………………………………………………….. 1
• 46 ………… 6295314 ………………Guide Wheel Assembly …………………………………………………………….. 1
• 47 ………… 6295315 ………………Blade Support Shaft w/Bearing …………………………………………………… 1
• 48 ………… 6295316 ………………Lower Guide Bracket ……………………………………………………………….. 1
• 49 ………… TS-0050051 …………Hex Cap Screw …………………………………………1/4”-20×1” ……………… 2
• 50 ………… 6295318 ………………Bracket …………………………………………………………………………………. 1
• 51 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4
• 52 ………… TS-0207021 …………Socket Head Cap Screw ……………………………..1/4”-20×1/2”……………. 4
• 53 ………… 6295320 ………………Lower Blade Guard ………………………………………………………………….. 1
• 54 ………… 6295321 ………………Locking Nut ……………………………………………………………………………. 1
• 55 ………… 6295322 ………………C-Ring …………………………………………………….E-5 ………………………. 1
• 56 ………… 6295323 ………………Air Nozzle ……………………………………………………………………………… 1
• 57 ………… 6295324 ………………Hose Clamp …………………………………………………………………………… 1
• 58 ………… TS-081C022 …………Screw ……………………………………………………..#10-24×3/8” ……………. 1
• 59 ………… 6295325 ………………Bracket …………………………………………………………………………………. 1
• 60 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 1
• 61 ………… TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 1
• 62 ………… 6295327 ………………Support Bearing Shaft (R) …………………………………………………………. 1
• 63 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 3
• 64 ………… TS-081C032 …………Phillips Pan Head Machine Screw………………….#10-24×1/2” ……………. 1
• 65 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 4
• 66 ………… TS-0267041 …………Socket Set Screw ………………………………………1/4”-20×3/8”……………. 4
• 67 ………… 2013-567……………..Eccentric Set Screw …………………………………………………………………. 1

Parts List: Guide Bracket Assembly (2415 Band Saw)

• Index No. Part No.                Description                                                    Size                           Qty
• 1 ………….. 6295275 ………………Guide Bar Case Bracket……………………………………………………………. 1
• 2 ………….. 6295276 ………………Cover ……………………………………………………………………………………. 1
• 3 ………….. TS-0081031 …………Hex Cap Screw …………………………………………5/16”-18×3/4” ………….. 4
• 4 ………….. TS-0050011 …………Hex Cap Screw …………………………………………1/4”-20×1/2”……………. 1
• 5 ………….. 6295278 ………………Pointer ………………………………………………………………………………….. 1
• 6 ………….. 6294835 ………………Guide Bar………………………………………………………………………………. 1
• 7 ………….. 6295280 ………………Worm ……………………………………………………………………………………. 1
• 8 ………….. 6295281 ………………Miniature Ball Bearing …………………………………609 ………………………. 1
• 9 ………….. 6295282 ………………C-Ring …………………………………………………….S-12……………………… 2
• 10 ………… 6295283 ………………Gear …………………………………………………………………………………….. 1
• 11 ………… TS-0208071 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/4” ……….. 6
• 12 ………… 6295285 ………………Gear Base……………………………………………………………………………… 1
• 13 ………… 6295286 ………………Set Block……………………………………………………………………………….. 1
• 14 ………… 6295287 ………………Thumb Screw ……………………………………………1/4”-20×1/4”……………. 1
• 15 ………… 6295288 ………………Inner Blade Guard …………………………………………………………………… 1
• 16 ………… 6295289 ………………Blade Guard …………………………………………………………………………… 1
• 17 ………… TS-0050021 …………Hex Cap Screw …………………………………………1/4”-20×5/8”……………. 4
• 18 ………… TS-0720071 …………Lock Washer …………………………………………….1/4” ………………………. 4
• 19 ………… TS-0680021 …………Flat Washer………………………………………………1/4” ………………………. 7
• 20 ………… 6295291 ………………Guide Bar Bracket …………………………………………………………………… 1
• 21 ………… TS-0270131 …………Socket Set Screw ………………………………………5/16”-18×2”…………….. 1
• 22 ………… 6295293 ………………Locking Handle………………………………………….1/4”x3/4” ……………….. 1
• 23 ………… TS-1521011 …………Socket Set Screw ………………………………………M4x4 ……………………. 4
• 24 ………… 6295294 ………………Knob …………………………………………………………………………………….. 2
• 25 ………… TS-0267021 …………Socket Set Screw ………………………………………1/4”-20×1/4”……………. 6
• 26 ………… 6295296 ………………Lever Shaft…………………………………………………………………………….. 1
• 27 ………… 6295297 ………………Hand Nut……………………………………………………………………………….. 2
• 28 ………… 6295298 ………………Bolt ………………………………………………………………………………………. 1
• 29 ………… 6295299 ………………Support Bearing Bracket (L) ………………………………………………………. 1
• 30 ………… 6295300 ………………Adjustment Bolt ………………………………………………………………………. 1
• 31 ………… TS-0207041 …………Socket Head Cap Screw ……………………………..1/4”-20×3/4”……………. 2
• 32 ………… 6295302 ………………Support Bearing Shaft ………………………………………………………………. 1
• 33 ………… 6295303 ………………Spacer ………………………………………………………………………………….. 2
• 34 ………… 6295304 ………………C-Ring …………………………………………………….S-15……………………… 4
• 35 ………… 6295305 ………………Ball Bearing………………………………………………6202 …………………….. 5
• 36 ………… 6295306 ………………Shaft …………………………………………………………………………………….. 2
• 37 ………… 6295307 ………………Knob ……………………………………………………….3/8”-16×2” ……………… 1
• 38 ………… TS-0208071 …………Socket Head Cap Screw ……………………………..5/16”-18×1-1/4” ……….. 4
• 39 ………… TS-0720081 …………Lock Washer …………………………………………….5/16” …………………….. 6
• 40 ………… 6295308 ………………Ball Bearing……………………………………………………………………………. 1
• 41 ………… 6295309 ………………Bracket …………………………………………………………………………………. 1
• 42 ………… TS-0208041 …………Socket Head Cap Screw ……………………………..5/16”-18×3/4” ………….. 2
• 43 ………… 6295311 ………………Plastic Washer ……………………………………………………………………….. 1
• 44 ………… 6295312 ………………Handwheel …………………………………………………………………………….. 1
• 45 ………… 6295313 ………………Handle ………………………………………………………………………………….. 1
• 46 ………… 6295314 ………………Guide Wheel Assembly …………………………………………………………….. 1
• 47 ………… 6295315 ………………Blade Support Shaft w/Bearing …………………………………………………… 1
• 48 ………… 6295316 ………………Lower Guide Bracket ……………………………………………………………….. 1
• 49 ………… TS-0050051 …………Hex Cap Screw …………………………………………1/4”-20×1” ……………… 2
• 50 ………… 6295318 ………………Bracket …………………………………………………………………………………. 1
• 51 ………… TS-0680031 …………Flat Washer………………………………………………5/16” …………………….. 4
• 52 ………… TS-0207021 …………Socket Head Cap Screw ……………………………..1/4”-20×1/2”……………. 4
• 53 ………… 6295320 ………………Lower Blade Guard ………………………………………………………………….. 1
• 54 ………… 6295321 ………………Locking Nut ……………………………………………………………………………. 1
• 55 ………… 6295322 ………………C-Ring …………………………………………………….E-5 ………………………. 1
• 56 ………… 6295323 ………………Air Nozzle ……………………………………………………………………………… 1
• 57 ………… 6295324 ………………Hose Clamp …………………………………………………………………………… 1
• 58 ………… TS-081C022 …………Screw ……………………………………………………..#10-24×3/8” ……………. 1
• 59 ………… 6295325 ………………Bracket …………………………………………………………………………………. 1
• 60 ………… TS-0560071 …………Hex Nut……………………………………………………#10-24 ………………….. 1
• 61 ………… TS-069204 …………..Flat Washer………………………………………………#10 ………………………. 1
• 62 ………… 6295327 ………………Support Bearing Shaft (R) …………………………………………………………. 1
• 63 ………… TS-0270031 …………Socket Set Screw ………………………………………5/16”-18×3/8” ………….. 3
• 64 ………… TS-081C032 …………Phillips Pan Head Machine Screw………………….#10-24×1/2” ……………. 1
• 65 ………… TS-0270051 …………Socket Set Screw ………………………………………5/16”-18×1/2” ………….. 4
• 66 ………… TS-0267041 …………Socket Set Screw ………………………………………1/4”-20×3/8”……………. 4
• 67 ………… 2013-567……………..Eccentric Set Screw …………………………………………………………………. 1

Guide Bracket Assembly (2013 and 2415)

Electrical Connections: 230 Volt, Single Phase – Model 2013 Band Saw ONLY

Magnetic Switch

Electrical Connections: 230 Volt, Single Phase – Model 2415 Band Saw ONLY

Magnetic Switch

Electrical Connections: 230 Volt, 3 Phase – Models 2013 and 2415

Magnetic Switch

Electrical Connections: 460 Volt, 3 Phase – Models 2013 and 2415

Magnetic Switch

Walter Meier (Manufacturing), Inc.

• 427 New Sanford Rd. LaVergne, TN 37086
• Phone: 800-274-6848
• www.powermatic.com.
• www.waltermeier.com.

References

• powermatic.com
• powermatic.com
• Home – Meier Tobler AG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>