MIRKA 2AK2S-BWM BWM Wireless Communication Module Instruction Manual
- June 13, 2024
- MIRKA
Table of Contents
INTEGRATION INSTRUCTIONS
For BT/Wifi module
IC ID: 22379-BWM
FCC ID: 2AK2S-BWM
General requirements
1.1 General
The BT/Wifi module with IC ID: 22379-BWM and FCC ID: 2AK2S-BWM (henceforth
“the module”) is only to be installed in Mirko Ltd. manufactured tools. OEM
use only. The module shall not be for sale to 3rd party.
1.2 Identification
Identification information for the BT/Wifi module:
US related identifying information.
FCC ID: 2AK2S-BWM
Canada related identifying information.
IC ID: 22379-BWM
HVIN: 22379-BWM
PMN: 22379-BWM
1.3 Placement
The module is approved for portable use, this means it may be installed in
such a way that it will be in close proximity (less than 20 cm) to the hands
and wrists of the end user in normal use. However, the module may not be
installed in such a way that it would be in close proximity (less than 20cm)
to the head or torso of the end user during normal use of the host device.
1.4 Technical installation
For instructions on the technical installation of the module, block
schematics, pin allocations, etc. see the module manufacturers datasheet.
Integration Instructions
2.1 General
The module shall not be for sale to 3rd party, and shall only be approved for
use by Mirko Ltd in its own products.
2.2 List of applicable FCC rules 15C (15.247)
2.3 Specific operational use conditions
2.3.1 Absolute Maximum Ratings
Stresses above those listed in Absolute Maximum Ratings may cause permanent
damage to the device. These are stress ratings only and functional operation
of the device at these or any other conditions beyond those indicated under
Recommended Operating Conditions is not implied. Exposure to absolute-maximum-
rated conditions for extended periods may affect device reliability.
| Symbol | Parameter | Min | Max | Unit |
|---|---|---|---|---|
| VDD33 | Power supply voltage | 0.3 | 3.6 | V |
| TSTORE | Storage temperature | -40 | 85 | °C |
Table 1: Absolute Maximum Ratings
2.3.2 Recommended Operating Conditions
| Symbol | Parameter | Min | Typ | Max | Unit |
|---|---|---|---|---|---|
| VDD33 | Power supply voltage | 3.0 | 3.3 | 4.6 | V |
| IV DD | Current delivered by external power supply | 0.5 | —- | — | A |
| T | Operating ambient temperature | -40 | — | 85 | °C |
Table 2: Recommended Operating Conditions
2.4 Limited module procedures
The module is approved for portable use, this means it may be installed in
such a way that it will be in close proximity (less than 20 cm) to the hands
and wrists of the end user in normal use. However, the module may not be
installed in such a way that it would be in close proximity (less than 20cm)
to the head or torso of the end user during normal use of the host device.
The module shall not be for sale to 3rd party, and shall only be approved for
use by Mirko Ltd in its own products.
2.5 Trace antenna designs
N/A
2.6 RF exposure considerations
The module is approved for portable use, this means it may be installed in
such a way that it will be in close proximity (less than 20 cm) to the hands
and wrists of the end user in normal use. However, the module may not be
installed in such a way that it would be in close proximity (less than 20cm)
to the head or torso of the end user during normal use of the host device.
2.7 Antennas
On-board PCB antenna.
2.8 Label and compliance information
N/A
2.9 Information on test modes and additional testing requirements
N/A
2.10 Additional testing, Part 15 Subpart B disclaimer
N/A
Legal
The following text is as to be included in the host devices user manual:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: changes or modifications not expressly approved by Mirko Ltd.
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Oliver Engström
Compliance and Documentation Specialist
Power Tools, Mirka Ltd.
Mirka Ltd
FI-66850 JEPPO
Finland
Tel: +358 (0)20 760 2111
e-mail:info@mirka.com
www.mirka.com
Business ID 0721789-4
VAT FI07217894
ISO 9001
ISO 14001
ISO 45001
MEMBER OF KWH CROUP
Documents / Resources
|
MIRKA 2AK2S-BWM BWM Wireless Communication
Module
[pdf] Instruction Manual
2AK2S-BWM BWM Wireless Communication Module, 2AK2S-BWM, BWM Wireless
Communication Module, Wireless Communication Module, Communication Module
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>