hama 00176651 Smart Camera User Manual

: June 1, 2024
: Hama

Table of Contents

hama 00176651 Smart Camera
Product Usage Instructions
Introduction
PACKAGING CONTENTS
Safety instructions
Installing the Hama Smart Home app
Product properties
Integrating devices into the Hama Smart Home
Setting options
Extended usage options with scenarios
Care and maintenance
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hama 00176651 Smart Camera

hama-00176651-Smart-Camera-PRODUCT

Specifications

Model: Smart Camera 00176651
Connectivity: USB-C 3.0
Storage: Micro SD card slot (supports MICRO SD)
Includes: 1x smart camera, 1x USB-C cable, 1x mounting kit, 1x quick guide, 1x warning, and safety instructions

Product Usage Instructions

Introduction

Thank you for choosing a Hama Smart Camera. Please read the following instructions carefully and keep them for future reference.

Safety Instructions

Ensure to follow all safety instructions provided in the manual to prevent any hazards or risks while using the product.

Installing the Hama Smart Home App

Download and install the Hama Smart Home app from the provided link. Make sure to use the latest version of the app for optimal performance.

Product Properties

Install the smart camera quickly and ensure no electric, water, gas, or other lines obstruct the mounting site.

Installation

Follow the installation guide in the manual to set up the smart camera effectively.

Integrating Devices into the Hama Smart Home

Refer to the App Guide for detailed instructions on integrating devices into the Hama Smart Home ecosystem.

Setting Options

Adjust various settings in the app including full-screen mode, picture capture, audio options, video recording, night mode, motion detection, and more.

Extended Usage Options with Scenarios

Explore creating scenarios in the app for extended usage options. Refer to Section 9 and the App Guide for detailed instructions.

FAQ

Q: How do I reset the smart camera?

A: Remove the rubber protector on one side of the camera and press the Reset button with a needle until a signal sound is heard. Once the LED flashes red, you can start a new pairing attempt.

Q: What do I need for video recording?

A: You need a cloud connection or a memory card inserted in the camera for video recording.

Introduction

Thank you for choosing a Hama product.
Take your time and read the following instructions and information completely.
Please keep these operating instructions in a safe place for future reference.
If you sell the device, please pass these operating instructions on to the new owner.

PACKAGING CONTENTS

Explanation of warning symbols and notes

Risk of electric shock
- This symbol indicates a risk of electric shock from touching uninsulated product parts that may carry hazardous voltage.
Warning
- This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
- This symbol is used to indicate additional information or important notes.

Explanation of symbols used on the product label

The product is intended only for indoor use.

Packaging contents

1x smart camera
1x USB-C cable
1x mounting kit
1x quick guide
1x warning and safety instructions

Safety instructions

Risk of electric shock

Do not open the device or continue to operate it if it becomes damaged.
Do not use the product if the AC adapter, the adapter cable, or the mains cable are damaged.
Do not attempt to service or repair the product yourself. Leave any service work to qualified experts.
Protect the product from dirt, moisture, and overheating, and use it in dry environments only.
This product is intended for private, non-commercial use only.
Use the product only for the intended purpose.
Do not use the product near heaters, other heat sources, or in direct sunlight.
Do not use the product in areas in which electronic products are not permitted.
Do not drop the product and do not expose it to any major shocks.
Do not modify the product in any way. Doing so voids the warranty.
Keep the packaging material out of the reach of children due to the risk of suffocation.
Dispose of packaging material immediately under the locally applicable regulations.
Do not operate the product outside the power limits given in the specifications.
Only use the article under moderate climatic conditions.
Do not mount the product above locations where persons might sit or stand.
Before mounting, check that the wall you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas, or other lines running through the wall at the mounting site.
Pay attention to the applicable data protection regulations before installing and using the product.
Respect the personal and property rights of others. Do not make recordings of other people with the camera.
Observe the right to one’s image and spoken word when recording.
As with all electrical products, this device should be kept out of the reach of children.

Installing the Hama Smart Home app

To use all the functions of the device, you need a smartphone/tablet and the Hama Smart Home app.

Note

The following operating systems are supported:
iOS 16.3 or later
Android 6.0 or later
Download the Hama Smart Home app from the App Store (iOS) or Google Play (Android) to your smartphone/tablet.
To install the app, follow the instructions on your smartphone/tablet.
Open the app on your smartphone/tablet.
While setting up the app, you will be asked whether the app has permission to access the functions of your smartphone/tablet. Say yes to these prompts for the full functionality of the device.
Register to create a new account. Alternatively, log in with the access data of your existing account.
Follow the instructions for setting up the app until you can add a new device.
A detailed description of the Hama Smart Home app and all of its functions can be found in our app guide at: www.hama.com article number Downloads ðApp operating instructions
Ensure that you are using the latest version of the Hama Smart Home app.

Product properties

The following steps are required to commission the device:

Connect the device to a properly installed and easily accessible mains socket.
Put the device in pairing mode by holding the button for around 5 seconds. The LED starts to flash quickly.

Installation

You can secure the camera into place using the adhesive pads or mounting kit supplied.

Warning – installation with adhesive

Be aware that the intended mounting surface must be free from dust and grease. Use a suitable cleaner from a specialist retailer for this.
Be aware that the adhesive pads are intended to be permanent. Carefully pull the adhesive pad off the mounting surface to remove it.
Various environmental influences, such as moisture in the air, sunlight, cold, etc., can impair the long-term stickiness of the adhesive pads.
Possible residue on the mounting surface after removal of the adhesive pads cannot be ruled out!

Warning – mounting kit

Do not mount the product above locations where persons might sit or stand.
Before mounting, check that the wall you have chosen is suitable for the weight to be mounted. Also make sure that there are no electric, water, gas, or other lines running through the wall at the mounting site.

Integrating devices into the Hama Smart Home

Warning

Only operate the product from an approved socket that is connected to the public power supply. The socket must be installed close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does not exceed the socket strip’s maximum throughput rating.
If you will not be using the product for a prolonged period, disconnect it from mains power.
Connect the camera to a suitable power supply unit and a properly installed socket.
The LED on the camera starts to flash quickly. If it does not, press and hold the Reset button (4) on the camera for around 5 seconds.
Open the app and sign in.
Press the + in the top right-hand corner to add a new device.
Choose Cameras from the list.
Now confirm that the camera’s LED is flashing quickly by ticking “Next step” and clicking on “Next”. Ensure that the QR code is at the top right.
Next, enter your WiFi password and confirm with NEXT.
Now scan the QR code with the camera from a distance of around 15 – 20 cm.
As soon as you hear a signal sound, click “Signal sound heard”.
Your camera is now connected.
Once the connection is successful, the LED stops flashing quickly and the app confirms that your camera is connected. You can now assign it a different name if you wish.
Click Finish to end the process.
You can now operate and configure the camera.

Note

A detailed description of the Hama Smart Home app and its full scope of functions can be found in our App Guide at:
www.hama.com Article Number Downloads App Operating Instructions

Note: Pairing restart

First, remove the rubber protector on one side of the camera. Now press the Reset button with a needle or another thin object until a signal sound is heard.
As soon as the LED starts to flash red, you can start a further pairing attempt.

Setting options

The following settings can be made in the app:

1	Activate full-screen mode.
2	Take a picture of the current live recording here.
3	Talk to the other party:

One-way audio: You can speak, but you will not be able to hear the other party.

Two-way audio: Both parties can speak and hear each other.

4| Record a video recording of the current activities.

(A cloud connection or the presence of a memory card is required here).

5| You can display and hide the functions
6| Playback video recordings from your gallery.
7| Open the photo album and view all of the images

captured.

For extended usage options, scenarios can be created in the app.

Extended usage options with scenarios

Scenarios and automated sequences that can be created in the app allow various combination options and usage options for these products, depending on the SmartHome products in your home.
Programming is always via the app (see Section 4 of the App Guide) and will be offered/suggested to you on an individual basis.

Standard usage option

Technical data

Maximum radio-frequency power transmitted	5 V DC
frequency band	2.4 GHz
Maximum radio-frequency power transmitted	< 100 mW

Care and maintenance

Note Disconnect the device from the mains before cleaning and during prolonged periods of non-use.
Only clean this product with a slightly damp, lint-free cloth, and do not use aggressive cleaning products.
Ensure that no water can enter the product.

Warranty Disclaimer

Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product, or failure to observe the use instructions and/or safety notes.

Service and support

Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-0 (German/English)
Further support information can be found here: www.hama.com

To limit exposure to electromagnetic fields

This device is intended for use at a distance of at least 20 cm from the body of the user or persons nearby.
This device must not be worn or carried on the body.

Declaration of conformity

Hama GmbH & Co KG hereby declares that the radio equipment type [00176651] complies with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following Internet address: https://uk.hama.com 00176651 Downloads
Hama GmbH & Co KG 86652 Monheim / Germany Service & Support www.hama.com +49 9091 502-0
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Hama GmbH & Co. KG is under license.
Other trademarks and trade names are those of their respective owners.
All listed brands are trademarks of the corresponding companies.
Errors and omissions excepted, and subject to technical changes.
Our general terms of delivery and payment are applied.