TAC-DDS9-012 Sniper Running Boards Instruction Manual

Table of Contents

TAC-DDS9-012-Sniper-Running-Boards-product

Specifications

Product Name: Sniper Running Board
Part Number: TAC-DDS9-012
Compatibility: 2019-Up Dodge RAM 1500 Quad Cab (Exclude 2019-2024 RAM 1500 Classic Quad Cab)
Estimated Installation Time: 60-120 minutes

FAQ

Q: Is drilling required for installing the Sniper Running Board?
- A: No, drilling is not required for installation.
Q: What tools are needed for the installation?
- A: You will need wrenches in sizes 10mm, 13mm, 16mm, and 18mm, as well as Allen wrenches in sizes 4mm, 5mm, 6mm, and 8mm.
Q: How long does it take to install the running board?
- A: The estimated installation time is between 60 to 120 minutes.

FITS:

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
□ 6mm| □ 7-8.5| | □ 10mm|

| □ 4mm
■ 8mm| ■ 18-20| ■ 13mm| □ 5mm
□ 10mm| □ 35-40| □ 16mm| □ 6mm
□ 12mm| □ 60-70| □ 18mm| □ 8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
ASSISTANCE IS RECOMMENDED.

TAC-DDS9-012-Sniper-Running-Boards-fig-2

TAC-DDS9-012-Sniper-Running-Boards-fig-3

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER SIDE INSTALLATION

STEP 1

Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).

STEP 2

Select (1) Front/Rear Upper Mounting Bracket (#2). Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.

STEP 3

Select (1) Front/Rear Lower Mounting Bracket (#1). Attach the Lower Bracket to the short side ofthe Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x16mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 3). Do not tighten hardware.

STEP 4

TAC-DDS9-012-Sniper-Running-Boards-fig-7

Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4). Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).

STEP 5

Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded stud with (2) 8mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.

STEP 6

Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting location, (Fig 7). Do not tighten hardware.

STEP 7

Select the Driver/Left Running Board.
- NOTE: The Driver/Left Running Board will have a “12-L” on the front.
- IMPORTANT: Do not slide Running Board front to back on the Brackets or damage to the finish may result. Attach the Step to the Mounting Brackets with (6) 8mm Combo Bolts, (Fig 8). Do not tighten hardware.

STEP 8

STEP 9

STEP 10

Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.