WELLSHAVE Precision Trimmer Instruction Manual
- June 1, 2024
- WELLSHAVE
Table of Contents
PRECISION HAIRCLIPPER
INSTRUCTIONS
COMPONENTS
- Sharp Stainless Steel Blade
- ON/OFF
- Standard 5V/USB charging port
Combs Brush
Standard 5V/USB charging port
PARAMETERS
Professional Hair Clipper
| Motor| Operating voltage: 3V⎓
---|---|---
Carbon brush motor
Battery
| 2500 mAh Li-ion battery
Charging time: about 3 hours
Operating time with full charge: about 3 hours
Charge
| USB connect with adapter 5V⎓1000mA
---|---
Power: 5W
USE THE RECHARGEABLE MODE
1
| 2
---|---
- Insert the charger into the tail of clipper, connect to the power to start charging
- Cord and cordless are available
FIXED-LENGTH FUNCTION
A: Use of Limit Comb: Cropped hair and Feature: ( 1.5,3,4.5,6,10,13 ) six lengths adjustment, control the hair length
- To determine the length of haircut
- To select the appropriate limit comb
13mm 10mm 6mm 4.5mm 3mm 1.5mm
Mount the limit comb:
- Align the limit comb with the blade edge
- Slightly forward push to mount it.
Disassemble the limit comb: Just pull hard the limit comb
BLADE REMOVAL & INSTALLATION
BLADE REMOVAL
-
Like the picture, press down the moving blade with the thumb and then remove the blade.
-
Please hold with the other hand to avoid the blade falling off.
BLADE INSTALLATION
-
Direct the blade (B) at the hair clipper’s slot (A) and plug in
-
Push the blade down until it clicks
CUTTER CLEANING AND MAINTENANCE
BLADE ALIGNMENT
- Your clippers were carefully examined to ensure that the blades were oiled and aligned before leaving our factory.
- Blades must be realign if they have been removed for cleaning or replacement
- To realign the blades, simply match the upper and bottom blades teeth up, point for point.(End of top blade teeth should be approximately 0.5-1.0mm back from bottom blade. Compare your clipper blades with the sketch)
- If blade alignment is incorrect, add a few drops of oil to the blade, turn clipper on for a few moments, turn off and unplug. Loosen screws slightly and adjust. Tighten screws after blade is aligned
CUTTER MAINTENANCE
- To maintain your clipper in peak condition, the blades should be oiled every few haircuts.
- To oil it properly, the unit should be held so the blades are in a downward position. With the clipper blade running, dispense 2-3 drops of oil across the top blade.
NOTE
1. Please do not disassemble the product.
2. Water must not be used to wash the clipper, keep away from the dampness
while operating.
3. Only use a little wet cloth or neutral liquid soap to clean the product.
4. Never charge the product above 40°C heat source or below 0°C environment.
Slight heating during the operating or charging is normal case
After the battery life expires, take off and throw the battery in safe manner into the designated recycling site. Never dump it randomly.
WARRANTY CARD
Product Name| Rechargeable Clipper for the Professional| Warranty
Period
---|---|---
Product Model| | Within one year since the purchase date
Purchase Date| From: (M/D/Y)| To:
(M/D/Y)
Customer
| Add.| | Name|
---|---|---|---|---
|
Tel.
|
Retailer
| Add.| | Name|
Name| |
Tel.
|
PRODUCT ASSURANCES
-
This product has been manufactured through the precise quality management and inspection process.
-
In case of any failure during the normal operating, customer may send to the retailer or maintenance center for free-of-charge maintenance.
(Battery and blade are quick-wear parts excluding from the warranty, which shall only be provided upon the payment -
Free service shall not be provided in either case below:
A. Any damage caused by the maintenance and transformation that is not recognized by the manufacturer.
B. Any damage caused by mistake, inadvertent use or accident.
C. Any damage caused by natural disaster and abnormal voltage.
D. Any damage caused by non-compliance with the notes as stated in this operating manual. -
This Warranty Card shall be the only proof of warranty, while the product maintenance against invoice shall not be allowed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>