WELLSHAVE FK-8588T Professional All In One Trimmer Set Instruction Manual

WELLSHAVE FK-8588T Professional All In One Trimmer Set

Product Information

Specifications

• Power Source: AC 100-240 V 50/60 Hz
• Motor Voltage: 3W
• Charging Time: 3 hours
• Working Time: 60 minutes
• Ni-MH Battery Capacity: 600mAh x 2

Description of Parts

1. Full Size Trimmer
2. ON/OFF Switch
3. Design Trimmer
4. Precision Trimmer
5. Nose Trimmer
6. Micro Shaver Trimmer
7. Five Combs a-e for the Full Size Trimmer
8. Stand Foot
9. Lubricating Oil
10. Brush
11. USB Cable (for DC 5V / 1A charger)

How to Start?

How to Assemble the Device?

1. When changing parts, use your finger to position the part correctly, align the heads with the body, and press the parts together (Fig. 3-4).
2. Remove the heads as shown in the image (Fig. 1-2).
3. Place the Full Size Trimmer with the comb facing backward in a balanced way until it clicks onto the head parts (Fig. 3,5).
4. There are four combs with four levels, as shown on the next page.

Full Size Trimmer Comb Levels

Precision Trimmer Comb Levels

How to Clean the Device?
To clean the device, simply disassemble it as shown in the image. Then use the cleaning brush to remove the dust by cleaning the inside (Fig. 13-14).

How to Charge the Device?

1. Charging via the USB cable is very convenient (Fig. 15).
2. Insert the plug of the USB cable directly into the device housing (Fig. 16).

Product Usage Instructions

1. Attach a comb to the Full Size Trimmer. If trimming for the first time, start with the maximum trim length setting.
2. Turn on the device.
3. Place the flat top of the trimmer comb against the skin.
4. Slowly slide the trimmer through the hair. Repeat if necessary.

FAQ

• Q: Can I use the device in water?
  A: No, do not use the device in water.

• Q: What should I do if the device is not working properly?
  A: If the device is not working properly, has been dropped or damaged, or has come into contact with water, do not use it and refer to the user manual for troubleshooting steps or contact customer support.

• Q: How long does it take to fully charge the device?
  A: It takes approximately 3 hours to fully charge the device.

Our products are desinged to meet the highest standard of quality,function- ality and design. We hope you enjoy using your new appliance. Please read the instructions for use carefully and keep in a safe place for future reference.

Caution

• Use this appliance only for its intended use as described in this manual.
• Do not use this product if it is not working correctly, if it has been dropped or damaged, or dropped into water.

Description

1. Full size trimmer
2. On/Off switch
3. Design trimmer
4. Precision trimmer
5. Nose trimmer
6. Micro shaver
7. 5 Guide combs
8. Stand base
9. Lubricating oil
10. Cleaning brush
11. USB cable

Specification

• Power source : AC 100-240 V 50/60 Hz
• Motor voltage : DC2.4V
• Fast charging time : 5 hours
• Work time : 60 mins
• Ni-MHBattery capacity :600mAh x 2

Getting started

CHARGING YOUR PERSONAL GROOMER
Before using your personal groomer for the first time, charge for 8 hours.

• Ensure the product is switched off.
• Connect the charging adaptor to the product and then to the mains. The charging indicator will light up.
• Your personal groomer cannot be overcharged. However, if the product is not going to be used for an extended period time(2-3months),unplug it from the mains and store. Fully recharge your personal groomer when you would like to use it again.
• To preserve the life of your batteries ,let them run out every six months then encharge for 14-16 hours.

Ho w to match the appliance

CHARGING YOUR PERSONAL GROOMER

• When changing the parts , first use the finger put the part in the right position, put the heads parts directing to the body align with the lock and press the parts. (Fig. 3-4)
• Remove out the heads parts as picture. (Fig 1-2)
• Match the full size trimmer positioning comb from front to back balancely till lock with heads parts.(Fig.5-6)
• There are four positioning combs with four levels as below.

Ways of mat ching full size t rimmer comb

Ways of matching precision trimmer comb

1. Remove out the positioning combs from back to front as picture. (Fig. 7-8)
2. Press the two sides of the micro shaver attachment and remove out from the body. (Fig.9)
3. Press the two sides of the micro shaver attachment and insert to the body. (Fig.10)
4. Match the precision trimmer positioning comb from up to down balancely till lock with heads parts (fig.11)
5. Choose different 4 levels positions for precision trimmer positioning comb from up and down. (Fig 12)

Ways of cleaning the appliance
When cleaning the appliance,just separate the appliance ,as the pie shows.Then use the cleaning brush.clear the dust by cleaning the inside parts.(Fig.13-14)

Ways of cleaning the appliance

1. USB Cable charge and very conveni ent. (Fig. 15)
2. Insert the appliance pug directly into the body. (Fig. 16)

How to use

TO THIN AND TAPER THE BEARD/ MOUSTACHE (Fig.21-22)

1. Attach a guide comb to full size trimmer. If you are trimmer for the first time start with the maximum trimming length setting.
2. Turn the unit on.
3. Place the flat top of the trimmer comb against the skin.
4. Slowly slide the personal groomer through the hair. Repeat from different directions as necessary.
5. If hair builds up in the trimmer comb during the trimming process, switch the unit off, pull off the comb and brush/rinse off.

TO DEFINE THE BEARD/ MOUSTACHE LINE (Fig. 17-18)

1. Hold the personal groomer with precision Trimmer Blade facing you.
2. Start with edge of beard/moustache line and gently lower the trimmer blade onto your skin. Use motions towards edge of beard/moustache line to trim to desired locations in facial area and away from beard in neck area

TRIMMING EDGE OF SIDEBURNS (Fig. 19-20)

Hold the personal groomer with precision Trimmer Blade facing you.
Start with edge of sideburn, and with the trimmer blades resting lightly against your skin, use motions towards edge of sidebum line to trim to desired locations in facial area.

USING THE MICRO SHAVER TRIMMER (Fig.24)

1. Attach the micro shaver trimmer
2. Hold the groomer so the micro shaver gently touches your face in a 45 degree angle.
3. Use short, well-controlled movements to shave around your Beard/- Moustache. Use your free hand to stretch your skin. This encourages the hair to stand upright, making it easier to shave. NOTE: The micro shaver was designed to shave the detail areas around your beard/moustache/sideburns. It was not designed to shave your entire face. For a close comfortable shave, guaranteed, use one of ante electric shavers.

TO REMOVE HAIR FROM NOSE AND EAR (Fig.23)

1. Attach nose trimmer attachment.
2. Insert the personal groomer gently into nostril or ear.
3. Gently move the goomer in and out of the nosbil or ear and at the same time rulate.
4. Avoid inserting the cutting unit more than 6mm into your nostril or ear.

ATTACHING AND REMOVING THE TRIMMER COMB ATTACHMENT
NOTE : Always ensure the personal groomer is switched off before changing any attachments.

TIPS FOR BEST RESULT

1. Beard, moustache and sideburn hairs should be dry.
2. Avoid using lotions before using your personal groomer. Comb your hair in the direction that it grows.
3. Remove trimmer comb attachment if you are: defining hairline edges such as sideburns, trimming the nape of your neck, trimming your beard line on front of neck.

Case for your personal groomer

CLEANING AND MAINTAINING YOUR PERSONAL GROOMER AFTER EACH USE

1. Turn the personal groomer off.
2. Gently brush the remaining hairs away/rinse under warm water from the guide comb and trimmer blade.

CLEANING CAUTIONS

1. Only the guide comb attachment and trimmer blade may be removed from the product for cleaning.
2. Cleaning should only be done with a soft brush, such as the brush supplied with the product.
3. Only use the light-grade oil supplied or sewing machine oil on the blades.
4. Do not use harsh or corrosive cleaners on the units or their blades.
5. Do not submerge in water as damage will occur.

STORAGE

1. Always store this appliance and cord in a moisture-free area. Do not store it in temperatures exceeding 140 F (60″C).
2. Do not wrap the cord of the charging adaptor around the appliance.

Important safety instructions

WARNING -TO REDUCE THE RISK OF BURNS, ELECTROCUTION, FIRE, OR INJURY TO PERSONS:

1. An appliance never be left unattended when plugged into a power outlet.
2. Keep the power plug and cord away from heated surfaces.
3. Make sure the power plug and cord do not get wet.
4. Do not plug or unplug the product with wet hands.
5. Do not use the product with a damaged cord. A replacement can be obtained via our International Service Centres.
6. Charge, use and store the product at a temperature between 15-Cand 35- C.
7. Always unplug from the mains when cleaning.
8. Only use the parts supplied with the appliance.
9. Keep this product out of reach of children. The use of this appliance by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge can give cause to hazards. Persons responsible for their safety should give explicit instructions or supervise the use of the appliance.

Protect the environment

DO NOT DISPOSE THE TRIMMER IN HOUSEHOLD WASTE AT THE END OF ITS USEFUL LIFE. DISPOSAL CAN TAKE PLACE AT OUR SERVICE CENTRES OR APPROPRIATE COLLECTION SITES.

CAUTION : Do not put in fire or mutilate your battery packs they may burst or release toxic materials.
Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment
(Fig.25)

Battery removal
Lift the ba ttery out of the housing b y using a scissor cut down the connec- tion between the body and the power line. twist the connecting wires until they break (Fig.26).
The battery must be removed from the appliance before it is scrapped.The battery is to be disposed of safely.

1. Unplug groomer from ontlet to avoid risk of electrical shock.
2. Remove rear groomer cover by first prying the rubber panel from the product with a flat head screwdriver. Pry the on/off switch from the product by head screwdriver. Unscrew the upper housing by head screwdriver and pry the upper housing from the product with a flat head screwdriver. This will expose the batteries.
3. With wire cutters, clip the wires leading to the batteries.
4. Remove the batteries from the product. Contact your local authorities for proper disposal.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>