TAC 3S-19D100T Side Steps Running Boards Instruction Manual

: June 1, 2024
: TAC

Table of Contents

TAC 3S-19D100T Side Steps Running Boards
Specifications
Product Usage Instructions
FAQ
PARTS LIST
PROCEDURE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAC 3S-19D100T Side Steps Running Boards

Specifications

Product Name: 3 90 DEGREE BENT END SIDEBARS
Compatible with: 2019-2024 Dodge Ram 1500 Quad Cab (Excluding 19-24 Ram 1500 Classic)
Part Number: 3S-19D100T
Manufacturer: www.tacautoparts.com.

Product Usage Instructions

Parts List

```
* 2 3 90 deg. Bent End Sidebars
```
- 1 Driver/left side Front Mounting Bracket
- 1 Passenger/right side Front Mounting Bracket

Installation Procedure

1. Start the installation under the driver/left side of the vehicle.

Select the driver/left Front Mounting Bracket and attach it to the factory studs.
Attach the driver/left Front Support Bracket to the body mount.
Repeat steps for rear mounting locations.
Attach the Sidebar to the Front and Rear Brackets.

Final Steps

Level and adjust the Sidebar as necessary.
Fully tighten all hardware.
Repeat the installation steps for the passenger/right Sidebar.
Do periodic inspections to ensure all hardware is secure and tight.

FAQ

Q: Are these sidebars compatible with all models of Dodge Ram 1500?
A: These sidebars are compatible with the 2019-2024 Dodge Ram 1500 Quad Cab, excluding the 19-24 Ram 1500 Classic.
Q: Do I need any special tools for installation?
A: It is recommended to use a wire brush or thread die to remove paint buildup on the threaded studs before installation. Assistance during installation is also recommended.

PARTS LIST

2	3” 90 deg. Bent End Sidebars	1	Driver/left side Rear Support Bracket
1	Driver/left side Front Mounting Bracket	1	Passenger/right side Rear

TAC-3S-19D100T-Side-Steps-Running-Boards-FIG-1

PROCEDURE

REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

Start the installation under the driver/left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Figure 1). IMPORTANT: Use a wire brush or thread die to remove paint buildup on the threaded studs before continuing with installation.
Select the driver/left Front Mounting Bracket, (Figure 2). Place the Bracket over the studs with the flat side against the body panel. Attach the Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figures 2 & 3). Leave the Bracket loose at this time.
Locate the front body mount next to the installed Bracket, (Figure 4). Remove the body bolt and washer, (Figure 5). NOTE: Clean threads on the body bolt to remove paint buildup before reinstalling.
Select the driver/left Front Support Bracket, (Figure 6). Reuse the factory body bolt and washer to attach the upper slot in the Support Bracket to the body mount. (Figures 7 & 8).
Move to the rear mounting location, (Figure 9). Repeat Steps 1—4 to attach the driver/left Rear Mounting Bracket and Support Bracket, (Figure 10).
Carefully unwrap and select (1) Sidebar. With assistance, line up the front end of the tube with the front Bracket, (Figure 11). Attach the front end of the Sidebar to the Front Brackets with the included 1/2” Hex Bolt, 1/2” Lock Washer and 1/2” Flat Washer, (Figures 11 & 12). Do not tighten the hardware.
Move to the rear of the Sidebar. Repeat Step 6 to attach the Sidebar to the rear Brackets, (Figure 13).
Level and adjust the Sidebar as necessary and fully tighten all hardware.
Repeat Steps 1—8 for the passenger/right Sidebar.
Do periodic inspections of the installation to make sure that all hardware is secure and tight.

To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Sidebar.

Driver/left Side Installation Pictured