TAC SW-C01 Sidewinder Running Boards Installation Guide

TAC SW-C01 Sidewinder Running Boards

Product Information

Specifications

• Product Name: Sidewinder Running Board
• Part Number: SW-C01
• Fits:
  • 2015-Up Chevy Colorado Crew Cab
  • 2015-Up GMC Canyon Crew Cab
• Installation Time: 60-120 minutes
• Cutting Not Required
• Drilling Not Required

Product Usage Instructions

Before Installation

1. Remove all contents from the box and verify all parts are present.
2. Read the instructions carefully before starting the installation.
3. It is recommended to seek assistance when installing.

Part List

• Driver/Left Side Bracket x 3
• Passenger/Right Side Bracket x 3
• 8mm x 30mm Hex Bolt x 12
• 8mm Flat Washer x 12
• 8mm Lock Washer x 12
• 8mm Clip Nut x 12
• 8mm x 25mm Combo Bolt x 12

FAQ

• Q: Is cutting required during the installation?
  • A: No, cutting is not required for installing the Sidewinder Running Board.
• Q: What tools are needed for installation?
  • A: You will need a wrench in sizes 10mm, 13mm, 16mm, and 18mm, as well as an Allen wrench in sizes 4mm, 5mm, 6mm, and 8mm.
• Q: How many mounting locations are there for the Passenger/Right side?
  • A: The installation uses the 1st, 2nd, and 4th mounting locations along the bottom and inner side of the body panel for the Passenger/Right side.

FITS:

• 2015-Up Chevy Colorado Crew Cab
• 2015-Up GMC Canyon Crew Cab

Torque & Tools

Part List

Installation Instruction

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER-SIDE INSTALLATION

STEP 1

Start the installation under the Passenger/Right side of the vehicle. Locate the front mounting location along the bottom and inner side of the body panel, (Fig 1). Installation will use the 1st, 2nd and 4th mounting locations. NOTE: It may help to hold a Bracket up in place to help determine the mounting holes to use along the bottom and inner side of the body

STEP 2

Remove rubber plugs as necessary from the holes in the side and bottom of the inner body panel, (Fig 2).

STEP 3

Select (2) 8mm Clip Nuts. Slide each Clip Nut into the large hole and over the smaller hole next to it. Line up threaded nut on the Clip Nut with smaller hole in body panel, (Fig 3)

STEP 4

Select (1) Passenger/Right Mounting Bracket. Attach the Mounting Bracket to the (2) Clip Nuts in the vehicle with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Fig 4). Do not tighten hardware.

STEP 5

Repeat Steps 1—4 to attach the remaining (2) Passenger/Right Mounting Bracket to the 2nd and rear locations, (Figs 5 & 6). Do not tighten hardware.

STEP 6

Select the Passenger/Right Running Board. NOTE: The Passenger/Right Running Board will have a “01-R” on the front. Carefully place Running Board on the brackets. IMPORTANT: Do not slide Running Board front to back on the Brackets or damage to the finish may result. Attach the Running Board to the Mounting Brackets with (6) 8mm Combo Bolts, (Fig 7). Do not tighten hardware.

STEP 7

Level and adjust the Running Board and fully tighten all hardware.

STEP 8

Repeat Steps 1—7 to attach the Driver/Left Running Board.

STEP 9

Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Running Boards.

• www.tacautoparts.com

References

• TACUSA
• TACUSA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>