KFI XP 1000 Polaris Ranger XP 1000 Rear Formed Bumper Installation Guide
- June 1, 2024
- KFi
Table of Contents
KFI XP 1000 Polaris Ranger XP 1000 Rear Formed Bumper
Product Information
Specifications:
- Product Name: Ranger XP 1000 Rear Bumper
- Part Number: 101900
- Compatibility: Formed for Ranger XP1000
Product Usage Instructions
Kit Components:
| Item # | Qty. | Description |
|---|---|---|
| 1 | 1 | Rear Bumper |
Installation Instructions:
- Each step must be mirrored on both sides of the machine.
- Hold the Passenger Side Bumper Bracket (4) in place inside the bed hinge and use bolts (7.2) and nuts (7.5) to bolt the brackets to the bed hinge as shown in Figures 1 & 2. Repeat this step for the Driver Side Bumper Bracket (5).
FAQ:
- Q: What should I do if I encounter missing hardware during installation?
A: If any hardware is missing, please contact our customer support for assistance and replacement parts.
Kit Components
| Item # | Qty. | Description |
|---|---|---|
| 1 | 1 | Rear Bumper Formed Ranger XP1000 |
| 2 | 1 | Passenger Side Conversion Bracket |
| 3 | 1 | Driver Side Conversion Bracket (not Shown) |
| 4 | 1 | Passenger Side Bumper Bracket |
| 5 | 1 | Driver Side Bumper Bracket |
| 6 | 1 | Hardware Kit HK-342 |
| 6.1 | 2 | 5/16”-18 x 1.00 Carriage Bolt Short neck gR5 Black |
| 6.2 | 4 | 5/16”-18 x .75 Carriage Bolt Short neck gR5 |
| 6.3 | 6 | 5/16”-18 Hex nut Flange nylock gR5 |
| --- | --- | --- |
| 7 | 1 | Hardware Kit HK-343 |
| 7.1 | 6 | 5/16”-18 x .75 Carriage Bolt Short neck gR5 Black |
| 7.2 | 8 | 5/16”-18 x .75 Hex Bolt Flange gR5 Serrated |
| 7.3 | 2 | 5/16”-18 x .75 Hex Bolt Flange Thread Cutting |
| 7.4 | 2 | 1/4”-20 x .75 Hex Bolt Flange Thread Cutting |
| 7.5 | 14 | 5/16”-18 Hex nut Flange nylock gR5 |
INSTALLATION INSTRUCTIONS
Note: Make sure all hardware needed to complete this mount is in the package. Thoroughly read through and understand the instructions before installing.
- Each step must be mirrored on both sides of the machine.
- Hold the Passenger Side Bumper Bracket (4) in place inside the bed hinge and use bolts (7.2) and nuts (7.5) to bolt the brackets to the bed hinge as shown in Figures 1 & 2. Repeat this step for the Driver Side Bumper Bracket (5).
- Once both Bumper Brackets are in place, use the 5/16” self-tapping screw (7.3) to secure the rear portion of the Bumper Bracket. This screw should be hand-tightened only or you could strip it out. See Figure 2.
- To assemble the bumper, locate the Formed Bumper (1) and Conversion Brackets (2 & 3). Install the Conversion Brackets onto the inside of the Formed Bumper with 3 black carriage bolts (7.1) and lock nuts (6.3) per side as shown at the top of Figure 3.
- Set the Bumper Assembly onto the Bumper Brackets (4 & 5) and secure using bolts (6.1 & 6.2) and nuts (7.5) as shown in the bottom of Figure 3.
- Level bumper and tighten all hardware evenly.
©2023 Copyright Kappers Fabricating, Inc. All rights reserved
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>