TAC 3S-C1092 Side Steps Instruction Manual

TAC 3S-C1092 Side Steps

PARTS LIST

PROCEDURE

REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

1. Start the installation under the passenger side of the vehicle. Locate the 4 factory running board mounting locations along the bottom and inner side of the body, (Figure 1). Mounting Brackets will bolt to the 1st, 2nd and 4th mounting locations. NOTE: It may help to hold a Bracket up in place to help determine the mounting holes to use along the bottom and inner side of the body.

2. Move to the front mounting location at the bottom corner of the body. Remove the rubber plugs from the bottom and side of the body panel as necessary, (Figure 2). Select (2) 8mm Clip Nuts. Slide the Clip  Nuts into the large holes and over the smaller holes. Line up the threaded nut on the Clip Nut with a smaller hole in the body panel, (Figure 3).

3. Select the passenger-side front Mounting Bracket. Line up the holes in the Bracket with the (2) Clip Nuts. Attach the Bracket to the Clip Nuts with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 4). Leave hardware loose at this time.

4. Next, carefully pull back the plastic lower fender cover and remove the (2) factory bolts in the bottom of the fender, (Figure 5). Select the passenger front Support Bracket, (Figure 6). Attach the Bracket to the (2) threaded holes with (2) 6mm x 20mm Hex Bolts and (2) 6mm Flat Washers, (Figure 7). IMPORTANT: Make sure the Support Bracket is behind the front Bracket. Snug but do not fully tighten hardware at this time.

5. Move along the side of the vehicle to the second mounting location, (Figure 1). Repeat Step 2 to install (2) 8mm Clip Nuts in the (2) factory holes in the body panel, (Figure 7). Select (1) Center Bracket.

6. NOTE: Center Bracket can be installed on either the driver or passenger side. Bolt the Mounting Bracket to the (2) Clip Nuts with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 8). Snug but do not fully tighten the hardware.

7. Skip the third mounting location and move to the last location at the back of the cab, (Figure 9). Repeat Step 4 to install the passenger side rear Mounting Bracket, (Figure 10).
   Passenger/right Side Installation Pictured

8. Select the passenger/right Sidebar. Carefully position the Sidebar up to the front and rear Mounting Brackets. Attach the Sidebar to the Mounting Brackets with (2) 1/2” x 2” Hex Bolts, (2) 1/2” Lock Washers, and (2) 1/2” Flat Washers, (Figures 10 & 12). Snug but do not tighten at this time.

9. Move to the Center Bracket. Line up the Bracket with the threaded inserts at the bottom of the Sidebar. Attach the Sidebar to the Bracket with (2) 8mm x 25mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 11). Do not tighten the hardware.

10. Level and adjust the Sidebar and tighten all hardware.

11. Repeat Steps 1—9 to install the driver/left Sidebar.

12. Do periodic inspections of the installation to make sure that all hardware is secure and tight. To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Sidebar. For gloss black finishes: Mild soap may be used to clean the Sidebar.

References

• TACUSA
• TACUSA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>