TAC 422400T-1 4 Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 422400T-1 4 Side Steps Running Boards
Product Information
Specifications
- Product Name: Upgraded 4 Oval Straight Sidebar
- Compatibility: 2018-2024 Jeep Wrangler JL 2DR
- Part Number: 422400T-1
Product Usage Instructions
Installation
- Ensure all parts from the parts list are available.
- Start with the driver/left side installation following the provided instructions.
- Proceed with the passenger/right side installation using the same steps mirrored.
- Use the specified bolts, washers, and nuts for each mounting location as indicated in the figures.
- After installation, wax the product to protect it and maintain its finish. Use a mild soap for cleaning.
Front Installation
- Attach the front mounting bracket to the designated location using the provided hardware (8mm and 10mm bolts).
- Secure the front support bracket to the rear side of the front mounting bracket as shown in Fig 3 and Fig 4.
Rear Installation
- Mount the rear support bracket to the rear mounting bracket using the specified bolts and nuts.
- Attach the rear support bracket to the back of the pinch weld following the provided instructions (Fig 7 and Fig 8).
Additional Steps
To ensure a secure fit, make sure all brackets are properly aligned and tightened according to the instructions. Regular maintenance, including waxing, is recommended to prolong the life of the sidebar.
FAQ
Q: Can I use any type of polish or wax on the sidebar?
A: It is recommended to use regular wax for protection. Avoid using products with abrasives that could damage the finish.
Q: How do I clean the sidebar?
A: You can use mild soap to clean the sidebar. Avoid harsh chemicals that may affect the finish.
Parts List
1| Driver/left side Upgraded 4” Oval Straight Sidebar| 4| 10-1.5mm x 30mm Hex
Bolts
---|---|---|---
1| Passenger/right side Upgraded 4” Oval Straight Sidebar| 8| 10mm x 24mm x
2mm Flat Washers
1| Driver/left side Front Mounting Bracket| 4| 10-1.5mm Nylon Lock Nuts
1| Passenger/right side Front Mounting Bracket| 8| 8-1.25mm Combo Bolts
1| Driver/right side Rear Mounting Bracket| 4| 8-1.25mm x 35mm Hex Bolts
1| Passenger/right side Rear Mounting Bracket| 4| 8mm x 28mm x 3mm Flat
Washers
1| Driver/left side Front Support Bracket| 4| 8mm Lock Washers
1| Passenger/right side Front Support Bracket| 8| 6-1.0mm x 25mm Hex Bolts
1| Driver/left side Rear Support Bracket| 16| 6mm x 22mm x 2mm Flat Washers
1| Passenger/right side Rear Support Bracket| 8| 6-1.0mm Nylon Lock Nuts
PROCEDURE
- REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- FACTORY-INSTALLED OR AFTERMARKET “ROCK RAILS,” SIDE STEPS, OR RUNNING BOARDS MUST BE REMOVED.
- Start installation toward the front of the passenger side of the vehicle and find the front threaded insert located in between the first pair of holes along the pinch weld, (Figure 1).
- Select the Passenger side Front Mounting Bracket, (Figure 2).
- IMPORTANT: Use the illustration above to properly identify the Mounting Bracket. Attach the Bracket to the threaded insert using (1) 8mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer, (Figure 2). Do not tighten the hardware at this time.
- Next, select the Passenger side Front Support Bracket, (Figure 3).
- IMPORTANT: Use the illustration above to help identify the correct Support Bracket. Use (1) 10mm Hex Bolt, (2) 10mm Flat Washers, and (1) 10mm Nylon Lock Nut to attach the Support
- Bracket to the rear side of the Front Mounting Bracket, (Figure 3). Attach the Support Bracket to the back of the pinch weld using (2) 6mm Hex Bolts, (4) 6 mm Flat Washers, and (2) 6mm Nylon Lock Nuts,(Figure 4).
- NOTE: Insert bolts from the outside of the pinch weld and through the Bracket. Do not tighten the hardware at this time.
- Move to the rear mounting location and locate the threaded insert and pair of holes on the pinch weld, (Figure 5). Repeat Steps 3 & 4 to install the Rear Brackets, (Figures 6—8).
- Select the Passenger/Right Sidebar. Use the illustration above to select the correct Sidebar. Carefully position the Sidebar onto the (2) Mounting Brackets.
- IMPORTANT: Do not slide, (front to back or rotate), the Sidebar on the Brackets, or damage to the finish on the Sidebar may result.
- Attach the Sidebar to the Mounting Brackets with (4) 8mm x 25mm Combination Hex Bolts, (Figures 9 & 10). Do not tighten the hardware.
- Level and adjust the Sidebar and tighten all hardware.
- Repeat Steps 1—7 for Driver/left Sidebar installation.
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
- To protect your investment, wax this product after installation. Regular waxing is recommended to add a protective layer over the finish.
- Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebar.
Passenger/right Side Installation Pictured
Documents / Resources
| TAC
422400T-1 4 Side Steps Running
Boards
[pdf] Instruction Manual
422400T-1 4 Side Steps Running Boards, 422400T-1, 4 Side Steps Running Boards,
Steps Running Boards, Running Boards, Boards
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>