HYDRO Taurus CP-300 Single Product Laundry Dispenser User Manual

HYDRO Taurus CP-300 Single Product Laundry Dispenser

Specifications

• Pump delay time: Adjustable
• Pump run time: Adjustable
• Pump lockout time: Adjustable
• Pump rate: Variable
• Wall-mounted transformer
• Hardwired remote with 2 buttons and 3 LEDs

Product Usage Instructions

Installation
Install the wall-mounted pump and remote unit

1. Attach mounting bracket to a solid surface using provided screws.
2. Slide the Taurus CP-300 onto the bracket and press firmly to lock in place.
3. Mount the remote unit on a clean, dry surface using the adhesive-backed fasteners.
4. Connect the Taurus CP-300 to the remote using the Cat 5e cable.

Install the supply and discharge tubing
Supply Tubing

1. Cut tubing and route from the product container to the intake pump tube.
2. Slip tubing through compression nut into fitting and tighten.
3. Place the other end of the tubing into the product container.

Discharge Tubing

1. Cut tubing and route from the discharge location to the outflow pump tube.
2. Slip tubing through compression nut into fitting and tighten.

Programming
Overview
The Taurus CP-300 dispenses liquid chemicals accurately. Press the START button once to begin a cycle based on your programmed settings.

Enter Programming Mode
To enter programming mode, follow the instructions provided in the user manual.

Programming the Start Delay Time
Adjust the start delay time as needed for your application.

Programming the Pump Run Time
Set the pump run time according to your requirements.

Programming the Pump Lockout Time
Adjust the pump lockout time based on your needs.

Programming the User Prime Feature
If applicable, set up the user prime feature following the manual instructions.

Saving the Programmed Settings
After programming, make sure to save your settings as instructed in the user manual.

FAQ

• Q: Can I install the Taurus CP-300 myself?
  A: The CP-300 should be installed by a qualified technician only, following all electrical and plumbing codes for safety reasons.

Overview

Operation
The Taurus CP-300 dispenses liquid chemicals with a high degree of accuracy and repeatability. A separately wired remote provides a convenient way to start the cycle. Simple mounting, setup, and low cost make it ideal for single-product applications. Once programmed, operation is simple. Press the START button once (the green LED will flash once to show your button press has been “accepted”) and the Taurus dispenser will begin a use cycle; using whatever pump delay time, pump run time and pump lockout time you have programmed.

General Specifications

Hardwired remote with 2 buttons and 3 LEDs

Hardwired remote with 2 buttons and 3 LEDs
WARNING!
The CP-300 should be installed by a qualified technician only, in accordance with all applicable electrical and plumbing codes.

Package Contents

1. Taurus CP-300 Pump, Cat 5e Cable (P/N 00-08879-00)
2. Wall Mount Kit (P/N 13-08607-00)
3. Wall Power Transformer, 100-240 VAC (P/N 10096229)
4. Programmer Remote (P/N 13-08602-06)
5. Adhesive-back Remote Fasteners (P/N 36-06158-16025)

Installation

Install the wall-mounted pump and remote unit
Install the Taurus CP-300 close to product containers (6.5 ft. / 2 m.) and farther away from direct sources of steam, water spray, and high temperatures.

1. Attach mounting bracket to solid surface (drywall, masonry, wood, cement, cinder block) with provided screws. Use appropriate hardware for the material, e.g., metal anchors in cement or cinder block.
2. Slide the Taurus CP-300 down onto bracket and press firmly to lock in place.
3. Mount remote unit on a clean and dry surface using the provided adhesive-backed fasteners.
4. Connect the Taurus CP-300 to the remote using the Cat 5e cable as shown.

Install the supply and discharge tubing
Supply Tubing

1. Cut tubing and route from product container to intake (left) pump tube. Slip tubing through compression nut into fitting and tighten.
2. Place other end of tubing into the product container.

Discharge Tubing

1. Cut tubing and route from discharge location to outflow (right) pump tube.
2. Slip tubing through compression nut into fitting and tighten.

WARNING!
Disconnect all power to the dispenser during installation, service, and/or any time pump cabinet is opened.

Install the wall-mounted transformer

1. Plug the wall transformer into an AC outlet.
2. Plug the barrel adapter into the Taurus CP-300 power connector at the bottom of pump unit.

The green LED on the pump will turn on, indicating power and the remote LEDs will flash a code that indicates the firmware revision.
NOTE: Use only the transformer specified from the manufacturer to ensure proper operation. Usage of transformer must conform to local laws and codes.

Prime the pump unit

1. Press and hold the START button on the remote unit. After 10 seconds the pump will start. Continue to hold the Start button down to draw product into the pickup tubing.
2. When the pickup tubing is free of air, release the START button to stop priming.

WARNING!
Always verify power source voltage with volt meter.

Programming

Overview
The Taurus CP-300 is programmed using the Taurus CP-300 Programmer Remote.

The remote’s two-button interface contains the following features:

The three remote LEDs indicate the pump’s state of operation as follows:

progress. LEDs scroll Red-Green-Yellow twice to indicate button is being ignored. Try again after use cycle finishes.

NOTE: Please refer to the following instructions for more information on LED indicator functionality.

Enter Programming Mode
The Taurus CP-300 dispenses liquid chemicals with a high degree of accuracy and repeatability. A separately wired remote provides a convenient way to start the cycle. Simple mounting, setup, and low cost make it ideal for single-product applications.
Press and hold the START and PROG SELECT buttons simultaneously for 10 seconds. All three LED indicators will illuminate to confirm that programming mode has been activated.
NOTE: Once in programming mode, pressing the PROG SELECT button will allow you to sequence through the four programming options:

• Start Delay Time
• Run Time
• Lockout Period
• User Prime

Each of these functions is described below.

Programming the Start Delay Time

1. Once in programming mode, press the PROG SELECT button once. The yellow LED indicator will illuminate.
2. With the yellow LED illuminated, press the START button once for every start delay increment you wish to add. Each press is confirmed by a yellow LED flash. Please refer to the table below to determine the number of presses needed for your desired delay time increment.

Yellow LED illuminates

NOTE: The LED will not flash if you press START after the time limit has been met.

Programming the Pump Run Time

1. Once the Start Delay Time has been programmed, press the PROG SELECT button again. The green LED indicator will illuminate.
2. Press and release the START button to start the Run Time.
   • The pump will turn on.
   • This works like a stopwatch; you press START to begin timing the Pump Run Time. Then you press START again to stop timing the Pump Run Time.
   • The green LED will flash every one second.
   • A Pump Run Time can be up to 20 minutes.
3. Press and release the START button again to stop the Run Time.
   • The pump will turn off
   • The green LED will remain on

Green LED illuminates

Programming the Pump Lockout Period
The is Pump Lockout Period can be used to prevent the press of the START button from pumping another product dose during the same use cycle.

Red LED illuminates

1. Once the Pump Run Time has been programmed, press the PROG SELECT button again. The red LED indicator will illuminate to indicate you can now program a Pump Lockout Period.
2. With the red LED illuminated, press the START button once for every five-minute lock-out period you wish to add. Each press is confirmed by a red LED flash. Please refer to the table below to determine the number of presses needed for your desired time increment.

NOTE: The LED will not flash when the time limit has been met (30 min).

• If, during normal operation, power to the dispenser is interrupted while in a Lockout Period, the balance of the Lockout Period will continue when power is restored.

Programming the User Prime Feature

1. Once the Pump Lockout Period has been programmed, press the PROG SELECT button again so you can program the User Prime feature.
   The green and yellow LED indicators will illuminate to indicate User Prime is enabled.

2. Press the START button again to disable the User Prime.
   The green and red LED indicators will illuminate to indicate User Prime is disabled.

Yellow and Green LED illuminated

The Yellow and Green LEDs indicate User Prime is enabled.
The Green and Red LEDs indicate User Prime is disabled.
NOTE: In other words, the green LED indicator stays on, while the yellow and red LED indicators toggle with each press of the START button to indicate whether the User Prime is enabled or disabled.
The User Prime feature, during normal operation, allows the operator to hold the START button down for 10 seconds to start the pump manually. The pump will continue to run while the START button is held down, and stop when the START button is released.

Saving the Programmed Settings
Red and Green LED illuminated

To exit programming mode and save the settings, press and hold the PROG SELECT button first, then press and hold the START button for 2 seconds.

• All three LED indicators will illuminate to indicate the programmed settings have been saved
• A program review will be conducted as follows:

increment for which the Start Delay Time was programmed. No flash indicates no Start Delay Time.
Pump Run Time| The green LED will use a long flash for each number of minutes, followed by quick flashes for each second for which the Pump Run Time was programmed.
Lockout Period| The red LED will turn on and flash for each five- minute increment for which the Lockout Period was programmed. No flash indicates 0 Lockout Period.
User Prime| The green and yellow LED indicators will illuminate if the User Prime is enabled. The green and red LED indicators will illuminate if the User Prime is disabled

NOTES:

• To exit programming mode without saving the settings, allow 20 seconds to lapse without pressing any buttons.
• To restore factory defaults, press and hold the START button and the PROG SELECT button simultaneously for ten seconds while powering up the unit. All three LED indicators will flash on and off twice to confirm that factory defaults have been restored.

Service Parts

Exploded Parts Diagram

Service Part Numbers

Specifications and Warranty Specifications

Installation Category: 2
Temperature| 10° to 49° C (50° to 120° F) maximum
Humidity| 95% relative humidity, maximum
Indoor Installation| Approved for indoor use only. Must not be installed outdoors.

Specifications subject to change without notice.

Limited Warranty
Seller warrants solely to Buyer the Products will be free from defects in material and workmanship under normal use and service for a period of one year from the date of completion of manufacture. This limited warranty does not apply to (a) hoses; (b) and products that have a normal life shorter than one year; or (c) failure in performance or damage caused by chemicals, abrasive materials, corrosion, lightning, improper voltage supply, physical abuse, mishandling or misapplication. In the event the Products are altered or repaired by Buyer without Seller’s prior written approval, all warranties will be void. No other warranty, oral, express or implied, including any warranty of merchantability or fitness for any particular purpose, is made for these products, and all other warranties are hereby expressly excluded. Seller’s sole obligation under this warranty will be, at Seller’s option, to repair or replace F.O.B. Seller’s facility in Cincinnati, Ohio any Products found to be other than as warranted.

Limitation of Liability
Seller’s warranty obligations and Buyer’s remedies are solely and exclusively as stated herein. Seller shall have no other liability, direct or indirect, of any kind, including liability for special, incidental, or consequential damages or for any other claims for damage or loss resulting from any cause whatsoever, whether based on negligence, strict liability, breach of contract or breach of warranty.

Hydro Systems
3798 Round Bottom Road Cincinnati, OH 45244

• Phone 513.271.88OO
• Toll Free 8OO.543.7184
• Fax 513.271.O16O
• Web hydrosystemsco.com

References

• Chemical Dilution, Dosing and Injection Equipment | Hydro Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>