TAC 40-23800T Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 40-23800T Side Steps Running Boards
Specifications
- Product: PNC Sidebars
- Compatibility: 2019-2024 Dodge Ram 1500 Quad Cab (Excluding 2019-2024 Ram 1500 Classic)
- Part Number: 40-23800T
- Website: www.tacautoparts.com
Product Usage Instructions:
Parts List
- 1 Driver/left side PNC Sidebar
- 1 Passenger/right side PNC Sidebar
- 6 Mounting Brackets
- 12 8-1.25mm x 25mm Combo Hex Bolts
- 18 8mm x 24mm x 2mm Flat Washers
- 18 8-1.25mm Nylon Lock Nuts
Installation Steps
- Start installation under the passenger side of the vehicle.
- Attach Mounting Brackets to factory studs with washers and lock nuts.
- Install Universal Brackets in center and rear mounting locations.
- Place Passenger/right Sidebar on top of Brackets without sliding.
- Attach Sidebar to Brackets using Combo Hex Bolts but do not tighten yet.
- Level and adjust Sidebar as necessary, then fully tighten all hardware.
- Repeat steps for Driver/left Sidebar installation.
- Periodically inspect the installation to ensure all hardware is secure and tight.
Maintenance
To protect your investment, wax the product after installation. Regular
waxing is recommended to add a protective layer over the finish. Use mild soap
for cleaning and avoid abrasive polishes or waxes that could damage the
finish.
FAQ
-
Q: Can the PNC Sidebars be installed on a 2019 Ram 1500 Classic?
A: No, the PNC Sidebars are not compatible with the 2019 Ram 1500 Classic model. -
Q: Do I need any special tools for installation?
A: Basic tools like a wire brush, wrench, and socket set are recommended for the installation process.
INSTALLATION INSTRUCTIONS
PNC SIDEBARS
2019-2024 DODGE RAM 1500 QUAD CAB
(EXCLUDING 2019-2024 RAM 1500 CLASSIC)
PART# 40-23800T
PARTS LIST:
| 1 | Driver/left side PNC Sidebar | 12 | 8-1.25mm x 25mm Combo Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right side PNC Sidebar | 18 | 8mm x 24mm x 2mm Flat Washers |
| 6 | Mounting Brackets | 18 | 8-1.25mm Nylon Lock Nuts |
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the passenger side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Figure 1). NOTE: Use a wire brush or die to remove paint buildup on the threaded studs.
- Select (1) Mounting Bracket. NOTE: All (6) Brackets are universal and will fit left or right side. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figure 2). Leave brackets loose at this time.
- Repeat Steps 1 & 2 to install the Universal Brackets in the center and rear mounting locations along the body panel, (Figures 3 & 4).
- Carefully unwrap and select the Passenger/right Sidebar. Use the illustration above to help identify the correct Sidebar. NOTE: The front stepping pad is closer to the front end of the Sidebar. Place the Sidebar on top of the Brackets. IMPORTANT: Do not slide, (front to back), the Sidebar on the Brackets or damage to the finish on the Sidebar may result.
- Attach the Sidebar to the Brackets with (6) 8mm Combo Hex Bolts, (Figures 5 — 7). Do not tighten hardware at this time.
- Level and adjust the Sidebar as necessary and fully tighten all hardware.
- Repeat Steps 1—6 for Driver/left Sidebar installation.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used also to clean the Sidebar.
Passenger/right Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>