TAC 40-04500T Side Steps Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 40-04500T Side Steps
Specifications:
- Product Name: PINNACLE 4 BENT END SIDE STEPS
- Compatibility: 2015-2024 Chevy Colorado/GMC Canyon Crew Cab
- Part Number: 40-04500T
- Website: www.tacautoparts.com
Product Usage Instructions
Parts List:
- Driver/left Sidebar
- Passenger/right Sidebar
- (6) Sidebar Brackets (universal for left or right)
- 8-1.25mm Clip-On Nuts
- 12 8-1.25mm x 25mm Hex Bolts
- 12 8mm x 24mm x 2mm Flat Washers
- 12 8mm Lock Washers
- 12 8mm x 25mm Combination Bolts
Installation Procedure:
- Start the installation under the passenger side of the vehicle.
- Locate the factory running board mounting locations along the bottom and inner side of the body.
- Remove rubber plugs from the holes in the side and bottom of the inner body panel.
- Bolt the Mounting Brackets to the Clip Nuts using Hex Bolts, Lock Washers, and Flat Washers.
- Install the remaining passenger side Brackets.
- Carefully position the Sidebar onto the Mounting Brackets and attach using Combination Hex Bolts.
- Level and adjust the Sidebar, then tighten all hardware.
- Repeat steps to install the driver/left Sidebar.
Maintenance Instructions:
To protect your investment, wax the product after installing. Regular
waxing is recommended to add a protective layer over the finish. Use mild soap
to clean the Sidebar. For stainless steel finishes, aluminum polish may be
used for small scratches and scuffs. Avoid using abrasive polishes or waxes
that could damage the finish.
Frequently Asked Questions (FAQ):
-
Q: Can I install these side steps alone?
A: It is recommended to have assistance during installation due to the size and weight of the product. -
Q: How do I know which Bracket goes on the left or right side?
A: The Brackets provided are universal and can be used on either side of the vehicle.
INSTALLATION INSTRUCTIONS
PINNACLE 4” BENT END SIDE STEPS
2015-2024 CHEVY COLORADO/GMC CANYON CREW CAB PART#40-04500T
PARTS LIST
| 1 | Driver/left Sidebar | 12 | 8-1.25mm x 25mm Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right Sidebar | 12 | 8mm x 24mm x 2mm Flat Washers |
| 6 | Sidebar Brackets (use for left or right) | 12 | 8mm Lock Washers |
| 12 | 8-1.25mm Clip-On Nuts | 12 | 8mm x 25mm Combination Bolts |
INSTALLATION INSTRUCTIONS
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
-
Start the installation under the passenger side of the vehicle. Locate the 4 factory running board mounting locations along the bottom and inner side of the body, (Figure 1). Mounting Brackets will bolt to the 1st, 2nd and 4th mounting locations. NOTE: It may help to hold a Bracket up in place to help determine the mounting holes to use along the bottom and inner side of the body.
-
Remove rubber plugs as necessary from the holes in the side and bottom of the inner body panel,
(Figure 2). Select (1) 8mm Clip Nut. Slide the Clip Nut into the large hole and over the smaller hole next to it in the side of the body panel. Line up threaded nut on the Clip Nut with smaller hole in body panel, (Figure 3). Repeat to install a Clip Nut in the bottom mounting location. -
Select (1) Mounting Bracket, (Figure 4). NOTE: All (6) Brackets are universal and will fit left or right side. Bolt the Mounting Bracket to the (2) Clip Nuts with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 5). Snug but do not fully tighten the hardware.
-
Repeat Steps 1—3 to install the (2) remaining passenger side Brackets, (Figures 6 & 7).
-
Select the passenger/right sidebar. Carefully position the Sidebar onto the (3) Mounting Brackets. IMPORTANT: Do not slide, (front to back or rotate), the Sidebar on the Brackets or damage to the finish on the Sidebar may result. Attach the Sidebar to the Mounting Brackets with (6) 8mm x 25mm Combination Hex Bolts, (Figures 5—7). Do not tighten hardware.
-
Level and adjust the Sidebar and tighten all hardware.
-
Repeat Steps 1—6 to install the driver/left Sidebar.
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and
scuffs on the finish. Mild soap may be used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Passenger/right Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>