TAC 3S-N1072 Side Steps Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3S-N1072 Side Steps
Specifications:
- Compatibility: 2004-2015/2017-2024 Nissan Titan Crew Cab, 2016-2024 Nissan Titan XD Crew Cab
- Part Number: 3S-N1072
- Material: Stainless Steel
- Finish Options: Gloss Black
- Includes: Driver/Left Sidebar, Passenger/Right Sidebar, Mounting Brackets, Bolts, Washers, Nuts
Product Usage Instructions
Installation:
- Identify the mounting locations along the body panel.
- Install the mounting brackets on the 1st, 2nd, and 4th mounting locations with the cradles facing the rear of the vehicle.
- Attach the driver sidebar to the mounting brackets using the provided combination bolts.
- Level and adjust the sidebar, then tighten all hardware.
- Repeat the process for the passenger sidebar installation.
- Periodically inspect the installation to ensure all hardware is secure.
Maintenance:
To protect your investment, wax the product after installation. Use
aluminum polish for stainless steel to address scratches. Clean with mild soap
for both stainless steel and gloss black finishes. Avoid abrasive polishes or
waxes that could damage the finish.
FAQ
-
Q: Can I use abrasive polish on the product?
A: No, it is not recommended to use any type of polish or wax that may contain abrasives as it could damage the finish of the product. -
Q: How often should I wax the product?
A: Regular waxing is recommended to add a protective layer over the finish. Waxing periodically will help maintain the product’s appearance and durability.
INSTALLATION INSTRUCTIONS
3” BENT END SIDEBARS
2004-2015/2017-2024 NISSAN TITAN CREW CAB 2016-2024 NISSAN TITAN XD CREW CAB
PART# 3S-N1072
www.tacautoparts.com
3” BENT END SIDEBARS
04- 15/17-24 NISSAN TITAN CREW CAB
16- 24 NISSAN TITAN XD CREW CAB
PARTS LIST
| 1 | Driver/Left Sidebar | 12 | 8-1.25mm x 25mm Combination Hex Bolts |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 12 | 8mm Lock Washers |
| 3 | Driver/Left Mounting Brackets | 6 | 8mm x 24mm OD x 2mm STD Flat Washers |
| 3 | Passenger/Right Mounting Brackets | 6 | 8mm x 16mm OD x 1.6mm Small Flat |
Washers
12| 8-1.25mm x 30mm Hex Bolts| 6| 8mm Nylon Lock Nuts
INSTALLATION INSTRUCTIONS
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Start installation at the front of the driver side of the vehicle and locate the factory threaded holes or stud located on the side of the inner body panel, (Figure 1). NOTE: Remove the plastic plug or any insulation on the side panel to locate the threaded holes.
- Select (1) driver side Mounting Bracket. Attach the Bracket to the mounting location with:
- Models with threaded stud: Attach Bracket to stud with (1) 8mm x 24mm STD Flat Washer and (1) 8mm Nylon Lock Nut. Next, insert (1) 8mm x 30mm Hex Bolt with (1) 8mm Lock Washer and (1) 8mm x 16mm Small Flat Washer through the remaining lower hole in the Bracket and into the threaded hole, (Figures 1A, 2 and 3). Do not tighten hardware at this time.
- Models without threaded stud: Attach Bracket to the upper threaded hole with (1) 8mm x 24mm STD Flat Washer, (1) 8mm Lock Washer and (1) 8mm x 30mm Hex Bolt. Attach Bracket to the lower threaded hole with (1) 8mm x 16mm Small Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Bolt, (Figure 1B & 2). Do not tighten hardware at this time.
- There are (4) mounting locations along the body panel. Bracket installation will use the 1st, 2nd and 4th mounting locations. Repeat the appropriate Steps 2—3 to install the center and rear Mounting Brackets,(Figures 2—6). NOTE: The cradles on the Mounting Brackets should be facing the rear of the vehicle when properly installed, (Figure 4).
- Once all three Mounting Brackets are partially installed, carefully place the driver Sidebar onto the Mounting Brackets. Use the included (6) 8mmx 25mm Combination Bolts to attach the Sidebar to the Mounting Brackets, (Figures 5 & 6).
- Level and adjust the Sidebar and tighten all hardware at this time.
- Repeat Steps 2—6 for passenger Sidebar installation.
- Do periodic inspections of the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and
scuffs on the finish. Mild soap may be used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Driver Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>