TAC 233800 Side Steps Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 233800 Side Steps
Specifications:
- Product Name: SIDEBAR
- Compatible Models: 2010-2024 Toyota 4Runner Limited, 2019-2022 4Runner Nightshade Edition, 2010-2013 SR5, 2022-2024 TRD Sport Models (Exclude All Models Not Listed)
- Part Number: 233800
Product Usage Instructions
Parts List:
- 1 Driver/Left Sidebar
- 1 Passenger/Right Sidebar
- 2 Front Mounting Brackets
- 4 Center & Rear Mounting Brackets
Installation Steps:
-
Step 1: Preparation
Before installation, make sure to gather all the parts listed in the parts list. -
Step 2: Cleaning and Maintenance
To protect your investment, wax the product after installing. Regular waxing is recommended to add a protective layer over the finish. Use mild soap to clean the Sidebar. For stainless steel, aluminum polish may be used to polish small scratches and scuffs on the finish. -
Step 3: Installation
-
Remove (2) factory hex bolts.
-
Install the Driver/Left Sidebar and Passenger/Right Sidebar using the provided Front Mounting Brackets and Center & Rear Mounting Brackets.
-
Refer to the provided images (Fig 1, Fig 3, Fig 4, Fig 5) for the correct mounting locations.
Frequently Asked Questions (FAQ):
-
Q: Can I use any type of polish or wax on the product?
A: Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel, aluminum polish may be used for small scratches and scuffs. Mild soap is recommended for cleaning. -
Q: How often should I wax the product?
A: Regular waxing is recommended to maintain a protective layer over the finish. The frequency of waxing can vary based on usage and environmental conditions.
INSTALLATION INSTRUCTIONS
SIDEBAR
2010-2024 Toyota 4Runner Limited
2019-2022 4Runner Nightshade Edition
2010-2013 SR5
2022-2024 TRD Sport Models (Exclude All Models Not Listed) PART# 233800
SIDEBAR
2010-2024 Toyota 4Runner Limited|2019-2022 4Runner Nightshade Edition
2010-2013 SR5|2022-2024 TRD Sport Models (Exclude All Models Not Listed)
PARTS LIST
| Qty | Description | Qty | Description |
|---|---|---|---|
| 1 | Driver/Left Sidebar | 24 | 8-1.25mm x 30mm Hex Bolts |
| 1 | Passenger/Right Sidebar | 24 | 8mm Lock Washers |
| 2 | Front Mounting Brackets | 24 | 8mm x 22mm OD x 2mm Flat Washers |
| 4 | Center & Rear Mounting Brackets |
INSTALLATION INSTRUCTIONS
PROCEDURE :
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED.
- Starting on the driver side front of the vehicle, remove the (2) factory hex bolts securing the lower rocker panel bracket to the bottom of the body, (Figure 1). NOTE: Only install (1) bracket at a time. Select (1) Front Mounting Bracket. Hold the Sidebar Bracket in place over the factory rocker panel bracket. Bolt the Mounting Bracket to the vehicle using the included (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 2). Do not tighten hardware at this time.
- Repeat Step 2 for Center and Rear Bracket installation, (Figures 3 & 4).
- With assistance, carefully place the Driver/Left Sidebar onto the (3) Brackets. WARNING: Do not rotate the Sidebar on the cradle or the finish on the Sidebar may be damaged. Align the threaded holes in the bottom of the Sidebar with the holes on the Mounting Brackets. Attach the Sidebar to the Mounting Brackets with the included (6) 8mm x 30mm Hex Bolts, (6) 8mm Lock Washers and (6) 8mm Flat Washers, (Figure 5). Do not tighten at this time.
- Level and adjust the Sidebar properly and tighten all hardware.
- Repeat Steps 2 – 5 for passenger Sidebar installation.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and
scuffs on the finish. Mild soap may be used also to clean the Sidebar.
For gloss black finishes: Mild soap may be used to clean the Sidebar.
Driver Side Installation Pictured
