TAC-DDS9-011 Sniper Running Board Instruction Manual

TAC-DDS9-011 Sniper Running Board

Product Information

Specifications

• Part Number: TAC-DDS9-011
• Compatible with: 2019-Up Dodge RAM 1500 Crew Cab
• Installation Time: 60-120 minutes
• Cutting Not Required
• Drilling Not Required

Product Usage Instructions

Before Installation

1. Remove all contents from the box and verify all parts are present.
2. Read the instructions carefully before starting the installation.
3. It is recommended to seek assistance during the installation process.

Part List

1. Front/Rear Lower Mounting Bracket x 4
2. Front/Rear Upper Mounting Brackets x 4
3. Center Mounting Bracket x 2
4. Center Support Bracket x 2

Tools Required

• Wrenches: 10mm, 13mm, 16mm, 18mm
• Allen Wrenches: 4mm, 5mm, 6mm, 8mm

Installation Steps

1. Step 1
   Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel.

2. Step 2
   Select (1) Front/Rear Upper Mounting Bracket (#2) and attach it to the factory studs using the provided washers and nuts. Do not tighten hardware.

3. Step 3
   Select (1) Front/Rear Lower Mounting Bracket (#1) and attach it to the Upper Bracket using the provided bolts, washers, and nuts. Do not tighten hardware.

4. Step 4
   Move to the center location and attach the Center Support Bracket (#4) to the lower threaded studs. Do not tighten hardware.

5. Step 5
   Select (1) Center Mounting Bracket (#3) and attach it to the Support Bracket and upper threaded stud. Do not tighten hardware.

6. Step 6
   Repeat Steps 2 & 3 to attach brackets to the rear mounting location. Do not tighten hardware.

FAQ

• Q: Is cutting required during installation?
  A: No, cutting is not required for installation.

• Q: Is drilling necessary for installing the Sniper Running Board?
  A: No, drilling is not required for installation.

SNIPER RUNNING BOARD
PART #: TAC-DDS9-011

FITS
2019-Up Dodge RAM 1500 Crew Cab
(Exclude 2019-2024 RAM 1500 Classic Crew Cab)

Torque & Tools

PLEASE NOTE THAT THE FOLLOWING  PICTURES ARE BASED ON THE DRIVER S IDE INSTALLATION

1. STEP 1
   Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).

2. STEP 2
   Select (1) Front/Rear Upper Mounting Bracket ( #2). Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.

3. STEP 3
   Select (1) Front/Rear Lower Mounting Bracket (#1). Attach the Lower Bracket to the short side of the Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x16mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 3). Do not tighten hardware.

4. STEP 4
   Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4). Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).

5. STEP 5
   Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded st ud with (2) 8mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.

6. STEP 6
   Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting location, (Fig 7). Do not tighten hardware.

7. STEP 7
   Select the Driver/Left Running Board. NOTE: The Driver/Left Running Board will have a “11-L” on the front. IMPORTANT: Do not slide Running Board front to back on the Brackets or damage to the finish may result. Attach the Step to the Mounting Brackets with (6) 8mm Combo Bolts,
   ( Fig 8). Do not tighten hardware.

8. STEP 8
   Level and adjust the Running Board as necessary and fully tighten all hardware.

9. STEP 9
   Repeat Steps 1—8 to attach the Passenger/Right Running Board to the vehicle.

10. STEP 10
    Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.

www.tacautoparts.com

References

• TACUSA
• TACUSA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>