Urant U18-300 Relay Wifi Router User Manual

Quick installation guide
Model:U18

Panel Layout

LED Explanation

away from the Host router.
Solid green| The U8 router is connected to the router, and is in a good location.
| Blinking green| One powered-on device is connected to the router s LAN / WAN port.
Off| No powered-on device is connected to the router s LAN / WAN port.

Button and port Explanation

Reset Button| Pressand hold this button for more than 5 seconds to reset the router to its factory default settings.
---|---
WPS Button| Pressthis button to enable the WPS function
LAN / WAN port| For connecting to a DSL/Cable modem, or an Ethernet jack.

WiFi Repeater mode

In this mode, the router boosts the existing wireless coverage in your home.

1. Connect Your Router
   Plug the extender into an electrical outlet near your host router, and then wait until the LED is on and then off.

Configure repeater mode

Methode ONE usis wrs w-Fi Poteete sets)
Using WPS is an easier way to extend your host network.You are recommended to use this method if your hostrouter has the WPS button. The button might look like one itnot please reter te Methode Two.

Connect

Relocate

1. Plug the extender into an electrical outlet between your router (Host Network) and the Wi-Fi”dead” zone.
   The location you choose must be within the range of your existing host network.

2. Wait until the LED is lit and solid Green. If not, relocate it closer to the router to achieve a good (or better) signal quality.

For Mobile phone users
Connect to the U18 router

1. Find the SSID(Network Name) printed on the I able of the U18 router.
2. Connect your Mobile phone to the U18 router’s network

Connect to the extender’network: Extender-a4f97c (The SSID on the lable of the U18 router)

Mode selection

Relocate

1. Plug the extender into an electrical outlet between your router (Host Network) and the Wi-Fi “dead” zone.
   The location you choose must be within the range of your existing host network.

2. Wait until the  LEO is lit and solid Green. If not, relocate it closer to the router to achieve a good (or better) signal quality.

Enjoy!
Extended Network Names: Host Router’s network name with _EXT at the end, but may have different SSIDs (network names) if you have customized them during the configuration. Extended networks Password:Share the same  passwords as those of your host networks.

AP mode

In this mode, the router transforms your existing wired network to a wireless.

1. Connect Your Router
   

2. Connect to the u1 router
   For Mobile phone users
   1. Find the SSID(Network Name) printed on the lable of the U18 router.
   2. Connect your Mobile phone to the U18 router’s network
   Connect to the extender’network: Extender-a4f97c (The SSID on the lable of the U18 router)

Mode selection

Set wifi password

Device restart

Router mode

1. Connect Your Router
   If your Internet connection is through a DSL/Cable modem,follow steps 1,2 and 4 to complete the hardware connections.
   If your Internet connection is through an Ethernet cable form the wall,follow steps 3 and 4 to complete the hardware connections.
   

2. Connect to the U18 router
   For Mobile phone users
   1. Find the S51D(Network Name) printed on the lab le of the U18 router.
   2.Connect your Mobile phone to the U18 router’s network
   Connect to the extender’network: Extender-a4f97c (The SSID on the lab le of the U18 router)

3. Mode selection

4. Set up Your Internet Connection
   You can modify the settings according to the service information provided by your ISP.

5. Click Finish to restart the device

Set up Your Internet Connection You can modify the settings according to the service information provided by your ISP.

Set up Your Internet Connection You can modify the settings according to the service information provided by your ISP.

If you choose Static IP,enter the information provided by your ISP in the corresponding fields.

If you choose PPPoE,enter the username and password provided by your ISP.
PPPoE users usually have OSL cable modems.

Enjoy!
Connect to the Extended networks (default SSID and passwork) and enjoy internet.but may have different network name and password, if you have customized them during the configuration.

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential  installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no  guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged  to try to correct the interference by one or more of thefollowing measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference  that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the  radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>