TAC 3S-T3322 Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3S-T3322 Side Steps Running Boards
Product Information
Specifications:
- Product Name: 3INCH SIDEBAR 2022-2024 TOYOTA TUNDRA DOUBLE CAB
- Part Number: 3S-T3322
- Brand: TAC Auto Parts
- Includes: Driver Sidebar, Passenger Sidebar, Mounting Brackets, Bolts, Washers
Product Usage Instructions
Installation Instructions:
- Ensure you have all the parts listed in the manual.
- Clean the Sidebars using mild soap before installation.
- Remove any plastic plugs or factory hex bolts from the designated mounting locations.
Driver/Left Side Installation:
- Attach the Driver/Left Front Mounting Bracket to the front mounting location using provided bolts and washers.
- Attach the Driver/Left Rear Mounting Bracket to the second mounting location.
- Secure the Driver/Left Sidebar to the Front Mounting Bracket using the provided combo bolts.
Passenger/Right Side Installation:
- Follow similar steps as Driver/Left Side Installation but for the Passenger/Right side.
Maintenance:
To protect your investment, avoid using polish or wax containing abrasives.
Use mild soap for cleaning.
FAQ (Frequently Asked Questions)
-
Q: Can I use any type of polish or wax on the Sidebars?
A: No, avoid using any polish or wax that may contain abrasives. Use mild soap for cleaning. -
Q: How many mounting brackets and bolts are included in the package?
A: The package includes front and rear mounting brackets for both Driver/Left and Passenger/Right sides, along with 16 bolts and washers.
INSTALLATION INSTRUCTIONS
3INCH SIDEBAR
2022-2024 TOYOTA TUNDRA DOUBLE CAB
PART# 3S-T3322
www.tacautoparts.com
PARTS LIST
| 1 | Driver Sidebar | 3 | Passenger/Right Rear Mounting Brackets |
|---|---|---|---|
| 1 | Passenger Sidebar | 16 | 8mm x 30mm Hex Bolts |
| 1 | Driver/Left Front Mounting Bracket | 16 | 8mm Lock Washers |
| 1 | Passenger/Right Front Mounting Bracket | 16 | 8mm x 24mm OD x 2mm Flat |
Washers
3| Driver/Left Rear Mounting Brackets| 16| 8mm x 25mm Combo Bolts
INSTALLATION INSTRUCTIONS
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND RUNNING BOARDS.
- Starting on the Driver/Left front of the vehicle, remove the plastic plugs or hex bolts covering the (2) threaded holes in the floor panel, (Figure 1).
- Select (1) Front Mounting Bracket, (Figure 2). Attach the Bracket to the mounting location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 3). Do not tighten hardware.
- Select (1) Rear Mounting Bracket. Repeat Step 3 to attach the Bracket to the mounting location shown in images below, (Figures 3&4).
- Continue to the rear mounting locations, (Figures 5 & 6). Repeat Step 3 to attach (1) Rear Mounting Bracket each to the 3rd and 4th mounting locations.
- Select the Driver/Left 3inch Sidebar. Attach the Sidebar to the Mounting Brackets with (8) 8mm Combo Bolts, (Figure 7). IMPORTANT: Do not slide the Sidebar, (forward or backward or rotate), on the Brackets or damage to the finish on the Sidebar may result. Do not tighten hardware.
- Level and adjust the 3inch Sidebar and tighten all hardware.
- Repeat Steps 2—7 to attach the Passenger/Right 3inch Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Driver/Left Side Installation Pictured
