TAC 3S-T3312 Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3S-T3312 Side Steps Running Boards
Product Information
Specifications
- Product: 3INCH SIDEBARS
- Compatible with: 2022-2024 Toyota Tundra CrewMax
- Part Number: 3S-T3312
Product Usage Instructions
Parts Included
- 1 Driver/Left Sidebar
- 1 Passenger/Right Sidebar
- 1 Driver/Left Front Mounting Bracket
- 1 Passenger/Right Front Mounting Bracket
- 3 Driver/Left Rear Mounting Brackets
- 3 Passenger/Right Rear Mounting Brackets
- 16 8mm x 30mm Hex Bolts
- 16 8mm x 25mm Combo Bolts
- 16 8mm Lock Washers
- 16 8mm x 24mm OD x 2mm Flat Washers
Cleaning Instructions:
To protect your investment, do not use any type of polish or wax that may
contain abrasives that could damage the finish. Use only mild soap to clean
the Sidebars.
Installation Instructions
Passenger/Right Side Installation:
Front Installation
- Remove plastic plugs (if equipped) or hex bolts from threaded holes at the front mounting location.
- Attach the Driver/Left Front Mounting Bracket to the front location.
- Attach the Passenger/Right Front Mounting Bracket to the front location.
Rear Installation
- Attach (1) Passenger/Right Rear Mounting Bracket to the second location.
- Attach (1) Passenger/Right Rear Mounting Bracket to the third location.
- Attach (1) Passenger/Right Rear Mounting Bracket to the rear location.
Attach the Passenger/Right PNC Sidebar to the (4) Mounting Brackets.
FAQ
-
Q: Can I use polish or wax on the Sidebars?
A: To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Sidebars. -
Q: How many Mounting Brackets are included in the package?
A: The package includes a total of 7 Mounting Brackets – 1 Driver/Left Front, 1 Passenger/Right Front, 3 Driver/Left Rear, and 3 Passenger/Right Rear.
INSTALLATION INSTRUCTIONS
3INCH SIDEBARS
2022-2024 TOYOTA TUNDRA CREWMAX
PART# 3S-T3312
PARTS LIST
| 1 | Driver/Left Sidebar | 3 | Passenger/Right Rear Mounting Brackets |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 16 | 8mm x 30mm Hex Bolts |
| 1 | Driver/Left Front Mounting Bracket | 16 | 8mm x 25mm Combo Bolts |
| 1 | Passenger/Right Front Mounting Bracket | 16 | 8mm Lock Washers |
| 3 | Driver/Left Rear Mounting Brackets | 16 | 8mm x 24mm OD x 2mm Flat Washers |
PROCEDURE
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS HIGHLY RECOMMENDED.
- Starting on the Passenger/Right side of the vehicle and remove the plastic plugs or hex bolts from the factory mounting location along the bottom of the body, (Figures 1 & 4).
- Select the Passenger/Right Front Mounting Bracket. Attach the Bracket to the front location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 2 & 3). Do not tighten hardware.
- Repeat Steps 2 & 3 to attach the (3) Rear Mounting Brackets, (Figures 4—8).
- Select the Passenger/Right Sidebar. Place the Sidebar onto the cradles of the Mounting Brackets. IMPORTANT: Do not Slide front to back or rotate the Sidebar or damage may result. Attach the Sidebar to the Mounting Brackets with (6) 8mm Combo Bolts, (Figure 9). Do not tighten hardware.
- Level and adjust the Sidebar and tighten all hardware.
- Repeat Steps 1—6 to attach the Driver/Left Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Use only mild soap to clean the Sidebars.
Passenger/Right Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>