TAC 4S-N1072-1 Side Steps Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 4S-N1072-1 Side Steps
Product Information
Specifications
- Product Name: Side Bar for 2005-2024 Nissan Frontier Crew Cab
- Part Number: 4S-N1072-1
- Manufacturer: www.tacautoparts.com
Product Usage Instructions
Parts List
- 1 Passenger/Right Side Bar
- 1 Driver/Left Side Bar
- 1 Front Passenger/Right Side Mounting Bracket
- 1 Rear Passenger/Right Side Mounting Bracket
- 1 Front Driver/Left Side Mounting Bracket
- 1 Rear Driver/Left Side Mounting Bracket
- 8 8-1.25mm x 30mm Hex Head Bolts
- 16 8X24mm OD.X2mm Flat Washers
- 16 8mm Lock Washers
- 8 8-1.25mm Nuts
Installation Procedure
- Remove contents from the box and verify all parts are present. Read instructions carefully.
- On the passenger/right side, if equipped, remove the existing running board by removing the four nuts holding the mount to the inside of the body. Install the two passenger/right side mounting brackets with the removed stock nuts, leaving nuts loose for now.
- Repeat procedures for the driver/left side.
- Install the side bar onto mounting brackets using four 8X25mm hex head bolts, four 8mm lock washers, and four existing nuts.
Note: If the vehicle is not equipped with factory sidebars, use the included 8mm Hex Nuts, Lock Washers, and Flat Washers.
FAQ
-
Q: What should I do if some parts are missing from the package?
A: In case of missing parts, please contact our customer support at support@tacautoparts.com for assistance. -
Q: Can I install this product on a different vehicle model?
A: This side bar is specifically designed for the 2005-2024 Nissan Frontier Crew Cab. Installing it on other vehicle models may not be compatible.
INSTALLATION INSTRUCTIONS
SIDE BAR
2005-2024 NISSAN FRONTIER CREW CAB
PART# 4S-N1072-1
PARTS LIST
| 1 | Passenger/Right Side Bar | 8 | 8-1.25mm x 30mm Hex Head Bolts |
|---|---|---|---|
| 1 | Driver/Left Side Bar | 16 | 8X24mm OD.X2mm Flat Washers |
| 1 | Front Passenger/Right Side Mounting Bracket | 16 | 8mm Lock Washers |
| 1 | Rear Passenger/Right Side Mounting Bracket | 8 | 8-1.25mm Nuts |
| 1 | Front Driver/Left Side Mounting Bracket | ||
| 1 | Rear Driver/Left Side Mounting Bracket |
PROCEDURE
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY.
- On the passenger/right side, if equipped, remove the existing running board by removing the four nuts holding mount to inside of body. Install the two passenger/right side mounting brackets with the removed stock nuts, leave nuts loose for now. NOTE: Holes in brackets are off set, install with holes towards front of truck, passenger/right side shown. See Fig. #1
- If not equipped with factory running boards – then use the four supplied 8mm nuts, washers & lock washers to install mounting brackets to truck.
- Repeat procedures 2 & 3 for driver/left side.
- Install side bar onto mounting brackets using four 8X25mm hex head bolts, four 8mm lock washers & four 8mm flat washers. Leave bolts loose – short end whole pattern installs towards the front of truck, passenger/right side shown.
- Repeat procedure #5 on driver/left side.
- Level and adjust side bars as desired and tighten.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>