TAC 233140 Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 233140 Side Steps Running Boards
Specifications
- Product: 3INCH SIDEBAR
- Vehicle Compatibility: 2022-2024 Toyota Tundra Double Cab
- Part Number: 233140
Product Usage Instructions
Parts List
- 1 Driver Sidebar
- 1 Passenger Sidebar
- 1 Driver/Left Front Mounting Bracket
- 1 Passenger/Right Front Mounting Bracket
- 3 Driver/Left Rear Mounting Brackets
- 3 Passenger/Right Rear Mounting Brackets
- 16 8mm x 30mm Hex Bolts
- 16 8mm Lock Washers
- 16 8mm x 24mm OD x 2mm Flat Washers
- 16 8mm x 25mm Combo Bolts
Installation Instructions
Step 1: Preparing for Installation
To protect your investment, do not use any type of polish or wax that may
contain abrasives that could damage the finish. Mild soap may be used to clean
the Sidebars.
Step 2: Removing Existing Hardware
Remove plastic plugs or factory hex bolts (if equipped) before proceeding
with the installation.
Step 3: Driver/Left Side Installation
Front Mounting
- Attach Driver/Left Front Mounting Bracket to the mounting location using (2) 8mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers.
- Proceed to the second mounting location and attach the Driver/Left Rear Mounting Bracket using the provided hardware.
Rear Mounting
- Secure the Sidebar to the Front Mounting Bracket using (2) 8mm Combo Bolts.
- Complete the installation by attaching the remaining Rear Mounting Brackets as per the instructions.
FAQ
Q: Can I use polish or wax on the Sidebars?
A: It is not recommended to use any polish or wax that may contain
abrasives. Mild soap is suggested for cleaning.
INSTALLATION INSTRUCTIONS
3INCH SIDEBAR
2022-2024 TOYOTA TUNDRA DOUBLE CAB
PART# 233140
PARTS LIST
1 | Driver Sidebar | 3 | Passenger/Right Rear Mounting Brackets |
---|---|---|---|
1 | Passenger Sidebar | 16 | 8mm x 30mm Hex Bolts |
1 | Driver/Left Front Mounting Bracket | 16 | 8mm Lock Washers |
1 | Passenger/Right Front Mounting Bracket | 16 | 8mm x 24mm OD x 2mm Flat |
Washers
3| Driver/Left Rear Mounting Brackets| 16| 8mm x 25mm Combo Bolts
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND RUNNING BOARDS.
- Starting on the Driver/Left front of the vehicle, remove the plastic plugs or hex bolts covering the (2) threaded holes in the floor panel, (Figure 1).
- Select (1) Front Mounting Bracket, (Figure 2). Attach the Bracket to the mounting location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 3). Do not tighten hardware.
- Select (1) Rear Mounting Bracket. Repeat Step 3 to attach the Bracket to the mounting location shown in images below, (Figures 3&4).
- Continue to the rear mounting locations, (Figures 5 & 6). Repeat Step 3 to attach (1) Rear Mounting Bracket each to the 3rd and 4th mounting locations.
- Select the Driver/Left 3inch Sidebar. Attach the Sidebar to the Mounting Brackets with (8) 8mm Combo Bolts, (Figure 7). IMPORTANT: Do not slide the Sidebar, (forward or backward or rotate), on the Brackets or damage to the finish on the Sidebar may result. Do not tighten hardware.
- Level and adjust the 3inch Sidebar and tighten all hardware.
- Repeat Steps 2—7 to attach the Passenger/Right 3inch Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Driver/Left Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>