TAC 3S-D108T Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3S-D108T Side Steps Running Boards
Product Information
Specifications
- Model: 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END)
- Vehicle Compatibility: 2009-2018 Dodge Ram 1500 Crew Cab (incl. 19-23 Ram 1500 Classic), 2010-2024 Dodge Ram 25-5500 Crew Cab (incl. Chassis Cab Diesel Models)
- Part Number: 3S-D108T
- Website: www.tacautoparts.com
Product Usage Instructions
Parts List
- 1 Driver/Left Sidebar
- 1 Passenger/Right Sidebar
Procedure
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Starting at the passenger side-front of the vehicle, remove the tape covering the factory oval holes in the inner body panel located by the front tire.
Frequently Asked Questions (FAQ)
-
Q: How do I know if these sidebars will fit my vehicle?
A: These sidebars are specifically designed for 2009-2018 Dodge Ram 1500 Crew Cab and 2010-2024 Dodge Ram 25-5500 Crew Cab models. Ensure you have the correct vehicle model before installation. -
Q: Can these sidebars be installed without professional help?
A: While it is recommended to have some mechanical knowledge, the installation instructions are detailed and can be followed by individuals with basic automotive skills.
INSTALLATION INSTRUCTIONS
3″ ROUND & 4″ OVAL SIDEBAR (90-DEG BENT END) 2009-2018 DODGE RAM 1500 CREW CAB
(INCL. 19-23 RAM 1500 CLASSIC)
2010-2024 DODGE RAM 25-5500 CREW CAB
(INCL. CHASSIS CAB DIESEL MODELS)
PART# 3S-D108T
PARTS LIST
Qty | Description | Qty | Description |
---|---|---|---|
1 | Driver/Left Sidebar | 4 | 1/2” X 1-1/2” OD x 1/8″ flat washers |
1 | Passenger/Right Sidebar | 4 | 12mm x 35mm Bolt/10mm Nut Plates |
1 | Driver/Left Front Mounting Bracket | 2 | 12mm x 32mm OD x 3mm Flat Washers |
1 | Passenger/Right Front Mounting Bracket | 2 | 12mm Lock Washers |
1 | Driver/Left Front Support Bracket | 2 | 12mm Hex Nuts |
1 | Passenger/Right Front Support Bracket | 4 | 12mm Plastic Retainers |
1 | Driver/Left Rear Mounting Bracket | 4 | 10-1.50mm x 35mm Hex Bolts |
1 | Passenger/Right Rear Mounting Bracket | 6 | 10mm x 30mm OD x 2.5mm flat |
washers
4| 1/2” x 2” Hex Bolts| 6| 10mm Lock Washers
4| 1/2” Lock Washers| 2| 10mm hex nut
4| 8mm-1.25 x 30mm Hex Bolts| 2| 10mm bolt plate
4| 8mm x 28mm OD x 3mm flat washers| 1| 10mm Fish Wire
4| 8mm Lock Washers| 2| 10mm Plastic Retainer
PROCEDURE
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
-
Starting at the passenger side-front of the vehicle, remove the tape covering the factory oval holes in the inner body panel located by the front tire.
-
For vehicles with wiring harness attached to front mounting location:
- Using a pry tool, pull out the pin attaching the wiring to the body panel, (Figure 1).
- Move wiring aside to allow for the installation of the Mounting Bracket.
-
Select (1) 10mm Bolt Plate and partially thread a Plastic Retainer onto it, (Fig 2A). Insert the Bolt Plate into the oval hole, (Fig 2B). Once the Bolt Plate is inserted, hold the Bolt end with one hand and tighten the Plastic Retainer with your other hand until it is tight against the body panel. IMPORTANT: The Plastic Retainer is designed to prevent the Bolt Plate from falling into the body cavity and to aid in installing the Mounting Bracket. For Mid-year 2015 models it will be necessary to use the 10mm fish wire to install this bolt plate. Insert fish wire into small slot and fish it until threaded end is present at large slot (Figure 3A). Pull this end out slightly and thread 10mm bolt plate onto end of fish wire (Figure 3B). Carefully feed bolt plate into rocker panel by pulling on opposite end of fish wire. Align 10mm bolt in slot and remove fish wire. Thread the 10mm plastic retainer down the bolt plate until it is flush against the sheet metal. (Figure 3C)
-
Next, partially thread a Plastic Retainer onto the threaded end of a 12mm Bolt /10mm Nut Plate, (Fig 2C).Insert the Bolt and Nut Plate with Plastic Retainer into the factory oval hole, (Figure 2B).
-
Select the passenger side front Mounting Bracket. Position the Mounting Bracket onto the (2) Bolt Plates. Using the threaded bolt as a handle, rotate the Bolt and Nut plate until the threaded Nut end lines up with the hole in the Mounting Bracket and body. Secure the Bracket to the Bolt Plates with (2) 10mm flat washers, (2) 10mm lock washers and (2) 10mm hex bolts. Do not tighten at this time. Mid-year 2015 Rams come equipped with pre-installed 8mm threaded inserts. Substitute (1) 8mm x 30mm Hex Bolt, (1) 8mm Flat Washer and (1) 8mm Lock Washer for the 10mm hardware. Snug but do not tighten hardware.
-
Remove the passenger side front factory body bolt. Select the passenger side Front Support Bracket. Insert the factory body bolt through the Support Bracket and up into its original position, (Figure 4). Line the other end of the Support Bracket up with the oval hole in the Front Mounting Bracket. Snug but do not tighten hardware at this time.
-
Move to the passenger side rear of the vehicle and remove the tape covering the factory oval hole in the inner body panel as described in Step 2. Thread a Plastic Retainer onto the threaded end of a Bolt and Nut Plate, (Figures 2C & 5). Insert the Bolt and Nut Plate into the factory hole, (see Steps 4 & 5).
-
Select the passenger side rear Mounting Bracket. Position the Mounting Bracket onto the installed Bolt and Nut Plate. Secure it with (1) 12mm Flat Washer, (1) 12mm Lock Washer and (1) 12mm Hex Nut,
(Figure 6). Do not tighten at this time. Rotate the Bolt and Nut plate until the threaded Nut end lines up with the remaining hole in the Mounting Bracket and body. Thread (1) 10mm x 35mm Hex Bolt, (1) 10mm Flat Washer and (1) 10mm Lock Washer into the threaded nut on the Bolt and Nut Plate. Mid-year 2015 Rams may come equipped with pre-installed 8mm threaded inserts at rear location. Substitute (1) 8mm x 30mm Hex Bolt, (1) 8mm Flat Washer and (1) 8mm Lock Washer for the 10mm hardware (Figure 6) Snug, but do not tighten hardware at this time. -
Select the passenger Sidebar and fasten it to the front Mounting Bracket and Support Bracket with the included (1) 1/2” x 2” Hex Bolt, (1) 1/2” Lock Washer and (1) 1/2” Flat Washer, (Figure 7). Do not tighten hardware at this time. Attach the Sidebar to the Rear Mounting Bracket with (1) 1/2” x 2” Hex Bolt, (1) 1/2” Lock Washer and (1) 1/2” Flat Washer, (Figure 6).
-
Level and align Sidebar properly and tighten all hardware including the factory body bolt.
-
Repeat Steps 2-10 for driver Sidebar installation. NOTE: Installation of front driver side bracket is the same as passenger side except that this bracket has no upper mount hole. The 12mm Flat Washer, Lock Washer and Hex Nut will not be used. (Figure 8) If 8mm threaded inserts are present, the 12mm bolt/10mm nut plate will not be used.
-
Do periodic inspections to the installation to make sure all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small
scratches and scuffs on the finish. Mild soap may be used also to clean the
Sidebar.
For gloss black finishes : Mild soap may be used to clean the Sidebar.
PASSENGER SIDE INSTALLATION PICTURED
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>