TAC 40-33140T Side Steps Running Boards Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 40-33140T Side Steps Running Boards
Product Specifications
- Product Name: 4INCH SIDEBAR 2022-2024 TOYOTA TUNDRA DOUBLE CAB
- Part Number: 40-33140T
- Website: www.tacautoparts.com
- Approximate Length: 19 inches between threaded inserts
- Mounting Brackets: Front and Rear for Driver/Left and Passenger/Right sides
- Hardware Included: Hex Bolts, Flat Washers, Lock Washers, Combo Bolts
Product Usage Instructions
Driver/Left Side Installation
- Remove plastic plugs or factory hex bolts (if equipped).
- Front Mounting:
- Attach Driver/Left Front Mounting Bracket to the floor panel using (2) 8mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers.
- Second Mounting:
- Attach Driver/Left Rear Mounting Bracket to the floor panel using (2) 8mm Combo Bolts.
- Final Step:
- Attach Driver/Left Sidebar to the Mounting Brackets.
Frequently Asked Questions (FAQ)
-
Q: Can I use polish or wax on the Sidebars?
A: To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars. -
Q: What is the distance between threaded inserts for the Front and Rear Mounting Brackets?
A: The approximate distances are 19 inches between threaded inserts for Front Mounting Brackets and 10 inches between threaded inserts for Rear Mounting Brackets.
INSTALLATION INSTRUCTIONS
4INCH SIDEBAR
2022-2024 TOYOTA TUNDRA DOUBLE CAB
PART# 40-33140T
PARTS LIST
| 1 | Driver/Left Sidebar | 3 | Passenger/Right Rear Mounting Brackets |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 16 | 8mm x 30mm Hex Bolts |
| 1 | Driver/Left Front Mounting Bracket | 16 | 8mm x 24mm OD x 2mm Flat Washers |
| 1 | Passenger/Right Front Mounting Bracket | 16 | 8mm Lock Washers |
| 3 | Driver/Left Rear Mounting Brackets | 16 | 8mm x 25mm Combo Bolts |
PROCEDURE
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND SIDE STEPS.
- Starting on the Driver/Left front of the vehicle, remove the plastic plugs or hex bolts covering the (2) threaded holes in the floor panel, (Figure 1).
- Select Driver/Left Front Mounting Bracket, (Figure 2). Attach the Bracket to the panel with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 2). Do not tighten hardware.
- Next, move to the second mounting location, (Figure 3). Select (1) Rear Mounting Bracket. Repeat Step 3 to attach the Bracket to the floor panel, (Figure 4).
- Continue to the rear mounting location, (Figure 5). Repeat Step 3 to attach (1) Rear Mounting Bracket to the floor panel.
- Select the Driver/left PNC Sidebar. Place the Sidebar onto the cradles of the Mounting Brackets. IMPORTANT: Do not rotate or slide the Sidebar front to back or damage to the finish may result. Attach the Sidebar to the Mounting Brackets with (8) 8mm Combo Bolts, (Figure 6). Do not tighten hardware.
- Level and adjust the Running Board as necessary and fully tighten all hardware.
- Repeat Steps 2—7 to attach the Passenger/Right Running Board.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Sidebars.
Driver/Left Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>