TAC BA214500 Side Steps Gloss Black 3 Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC BA214500 Side Steps Gloss Black 3
Product Information
Specifications
- Compatibility: 2015-2024 Ford F150, 2022-2024 F150 Lightning EV Super Crew Cab, 2017-2024 F250-550 Super Duty Super Crew Cab
- Part Number: BA214500
- Includes: Driver/left Sidebar, Passenger/right Sidebar, Front-passenger/rear Brackets, Center Brackets, Washers, Bolts, Lock Washers, Nylon Lock Nuts
Product Usage Instructions
Installation Procedure
- Remove all contents from the box and verify that all parts are present.
- Start the installation under the driver side of the vehicle and locate the factory running board mounting locations.
- Slide a Plastic Washer over each factory mounting stud to prevent corrosion.
- Attach the Mounting Brackets using Flat Washers and Nylon Lock Nuts. Snug but do not fully tighten the hardware.
- Install the Center Bracket using the same process as above.
- Repeat the steps to install the rear Bracket on the driver side.
- Position the Sidebar with assistance and attach it to the Mounting Brackets using the provided hardware. Leave hardware loose at this time.
- Attach the Sidebar to the Center Bracket with additional hardware, ensuring it is leveled and adjusted properly.
- Tighten all hardware and repeat the steps for the passenger/right Sidebar installation.
- Periodically inspect the installation to ensure all hardware remains secure and tight.
FAQ
-
Q: Can these 90-degree bent end sidebars be installed on other vehicle models?
A: These sidebars are specifically designed for 2015-2024 Ford F150, 2022-2024 F150 Lightning EV Super Crew Cab, and 2017-2024 F250-550 Super Duty Super Crew Cab models. Installing them on other vehicles may not be compatible. -
Q: How often should I inspect the installation?
A: It is recommended to do periodic inspections to ensure that all hardware remains secure and tight. Check the installation at regular intervals to maintain safety and stability.
INSTALLATION INSTRUCTIONS
90-DEGREE BENT END SIDEBARS
2015-2024 FORD F150 & 2022-2024 F150 Lightning EV SUPER CREW CAB
17-24 F250-550 SUPER DUTY SUPER CREW CAB
PART# BA214500
www.tacautoparts.com
PARTS LIST
PROCEDURE
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the driver side of the vehicle. Locate the front, center and rear factory running board mounting locations along the inner side of the body, (Figure 1).
- Slide (1) Plastic Washer over each factory mounting stud in the body panel, (Figures 2 & 3). IMPORTANT: The Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. Do not install the Brackets without the Plastic Washers.
- Select (1) driver side front Mounting Bracket. NOTE: Same bracket is used for the passenger side rear installation. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Figure 4). Snug but do not fully tighten the hardware.
- Select (1) Center Bracket. Repeat Steps 1—3 to install the driver side center Bracket, (Figure 5). NOTE: Center Bracket is the same, driver side and passenger side.
- Repeat Steps 1—3 to install the driver side rear Bracket, (Figure 6). NOTE: Same Bracket is used for the passenger side front installation.
- Select the driver/left Sidebar. With assistance, position the Sidebar up to the front and rear Mounting Brackets. Attach the Sidebar to the Mounting Brackets with the included (2) 1/2” x 2” Hex Bolts, (2) 1/2” Lock Washers, and (2) 1/2” Flat Washers, (Figure 6). Leave hardware loose at this time.
- Line up the threaded insert in the bottom of the Sidebar with the center Bracket. Attach the Sidebar to the Bracket with (1) 8mm x 25mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 7). Leave hardware loose at this time.
- Level and adjust the Sidebar and tighten all hardware.
- Repeat Steps 1—8 to install the passenger/right Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investmen t, wax this product after installing. Regular
waxing is recommended to add a protective layer over the finish. Do not use
any type of polish or wax that may contain abrasives that could damage the
finish.
For stainless steel : Aluminum polish may be used to polish small
scratches and scuffs on the finish. Mild soap may be used also to clean the
Sidebar.
For gloss black finishe s: Mild soap may be used to clean the Sidebar.
Driver/left side installation pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>