HITOSINO HS-CUB04G2T-LIAZ 4MP Optical Zoom IP Camera User Guide
- June 1, 2024
- HITOSINO
Table of Contents
HITOSINO HS-CUB04G2T-LIAZ 4MP Optical Zoom IP Camera
Specifications
- Resolution : 4MP
- Power Supply: 12V/0.8A
- Network Connectivity : Wired
- Supported Platforms : Web, App (Guarding Vision), iVMS4200
Product Usage Instructions
Connect Camera
Before activating the camera, follow these steps to connect the 4MP camera:
- Power the camera using a 12V/0.8A power supply.
- Connect the camera to your router using a network cable.
Activate Camera
To activate the camera:
- Download the SADP software from here.
- Open SADP, refresh, tick the camera, and set the camera password.
- Enable DHCP and set an administrator password.
Access Camera
Access Camera via Web
- Login to the camera’s webpage by double-clicking the camera’s IPV4 address on SADP or entering the IPV4 address in a browser.
- Enter login information (Username: ADMIN, Password: **).
- If the video is not visible, click Download Plug-in.
Access Camera via App – Guarding Vision
- Follow the instructions in the video provided to add the camera to the Guarding Vision app.
- Enter the administrator password created during activation.
- Create a Verification Code for encrypted video.
Access Camera via iVMS4200
- Download and install iVMS4200 from here.
- Add the camera to iVMS4200 by following the steps provided in the video.
How to Enable Smart Functions on the Camera
Enable Smart Functions via Web Browser Enable Audio
To enable audio:
- Access the IP camera via a web browser.
- Go to Configuration > Video/Audio and set Stream Type and Video Type for Main Stream and Sub Stream accordingly.
- Save the settings.
Enable Human/Vehicle Detection
To enable human/vehicle detection:
- Access the IP camera via a web browser.
- Go to Configuration > Event(Basic Event) and configure Motion Detection settings.
- Select the detection area and target type (Human, Vehicle, or both).
- Save the settings.
FAQ
- Q: How can I reset the camera?
- A: To reset the camera, locate the reset button on the device and press it for 10 seconds until you hear a beep indicating a successful reset.
CONNECT CAMERA
BEFORE ACTIVATE CAMERA, PLEASE FOLLOW THIS WAY TO CONNECT THIS 4MP CAMERA.
- Power camera via a power supply(12V/0.8A)
- Use a network cable to connect the camera to your router
ACTIVATE CAMERA
Instructional video link https://www.youtube.com/watch?v=fxnHVJGzUIA&t=5s
DOWNLOAD SADP TO ACTIVATE CAMERA
- Download URL: https://hitosino.com/
- Click: “Support-Download center”, then Download SADP
ACTIVATE CAMERA VIA SADP
Open SADP-Click “Refresh”-Tick the camera
TICK DHCP AND SET THE ADMINISTRATOR PASSWORD
ACCESS CAMERA
ACCESS CAMERA VIA WEB
LOGIN THE WEBPAGE OF CAMERA
You can double-click the camera’s IPV4 address on the SADP, or enter the camera’s IPV4 address in the browser to accidentally enter the camera’s web login interface
ENTER LOGIN INFORMATION
USER NAME: ADMIN
Password : ** (You set in chapter 1.2
ACCESS CAMERA VIA APP- GUARDING VISION
Instructional video link https://www.youtube.com/watch?v=GSfZEbtiJJ8
- Click Add Device
- Scan QR Code
- Choose Camera wired
- Connected and Next
- Enter the administrator password. (You set in Chapter 1.3)
- Create a Verification Code for Encryption of Video
ACCESS CAMERA VIA IVMS4200
- IInstructional video link https://www.youtube.com/watch?v=EbvRWKer9YY
- How to activate the camera via iVMS4200: From 0 seconds to 1 minute and 51 seconds
- How to add a camera: Watch from 1 minute 51 seconds
DOWNLOAD IVMS4200 TO ACTIVATE CAMERA
- Download URL: https://hitosino.com/
- Click: “Support-Download center”, then Download IVMS4200
ADD CAMERA TO IVMS4200
- Click Device Management- Device-Click Refresh
- Tick the camera you need to add
Create a name for camera- Enter User name: admin, Password: ***(You set when activate camera-Chapter 1.2)
- Click Add
The camera has been added to iVMS4200
How to enable Smart functions on the camera
Enable Smart functions via Web Browser
Enable audio
Steps:
Access the IP cameras via your web browser, Go to
- Configuration >
- Video/Audio,
- then select Stream Type to be Main Stream and Sub Stream separately and
- set video type of both streams to be Video&Audio,
- then click Save.
Enable Human/Vehicle Detection
Steps:
Access the IP cameras via your web browser, Go to Configuration >
- vent(Basic Event), Enter module
- Motion Detection, Check the
- Enable the Motion Detection function, Click the
- Draw Area button and
- use the mouse to select the required detection area in the video screen (as shown by the red grid lines in the screenshot).
- Check the target type you want to detect: Human or Vehicle or both of them,
- then click Save.
Enable Smart Color Night Vision
Steps:
Access the IP cameras via your web browser, Go to Configuration >
- Image, Enter module
- Display Settings, click
- Day/Night Switch, then set Supplement Light Mode to be Smart
Enable Smart functions via NVR
Enable audio
Steps:
Access the IP cameras via your nvr. Go to Configuration >Record >Parameter,
then select Stream Type to be Main Stream and Sub-Stream separately and set
video type of both Stream Type to be Video&Audio, click Copy to and check the
camera, click OK, then click Apply
Sub-Stream
Enable Human/Vehicle Detection
Steps:
Access the IP cameras via your nvr.
Go to Configuration >Event >Normal Event, enter module Motion Detection, then
select camera, check the Enable, check the target type you want to detect:
Human or Vehicle or both of them, click the Full-Screen button to select the
detection area (as shown by the red grid lines in the screenshot), then click
Apply
Enable Smart Color Night Vision
Steps:
Access the IP cameras via your nvr.
Go to Configuration >Camera >Display, and select Camera. Enter module
Day/Night Switch, then select Supplement Light Mode to be Smart or other mode
you need, then click Apply