TAC 3S-T123T 3 Inch Side Steps Running Boards Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 3S-T123T 3 Inch Side Steps Running Boards
Specifications
- Model: 3 Side Bar 2019-2024 Toyota RAV4
- Part Number: 3S-T123T
- Material: Stainless steel
- Includes: Driver/Left Sidebar, Passenger/Right Sidebar, Mounting Brackets, Bolts, Washers, Nuts, Retainers
Installation Steps
- Attach Driver/Left Front Mounting Bracket using provided hardware.
- Attach Passenger/Right Front Mounting Bracket using the specified bolts, washers, and nuts.
- Repeat the process for the Center and Rear Mounting Brackets on both sides.
- Securely attach the Sidebars to the mounting brackets using the Combo Bolts.
- Perform periodic inspections to ensure all hardware is secure and tight.
Cleaning Instructions
To clean the Sidebar, use mild soap and water. Avoid using polish or wax
containing abrasives. For stainless steel, you can use aluminum polish for
small scratches and scuffs.
Frequently Asked Questions (FAQ)
Q: Can I install the Sidebars on a different car model?
A: These Sidebars are specifically designed for the 2019-2024 Toyota RAV4
model. Using them on a different model may not provide a proper fit.
INSTALLATION INSTRUCTIONS
3″ SIDE BAR
2019-2024 TOYOTA RAV4
PART# 3S-T123T
PARTS LIST
| 1 | Driver/Left Sidebar | 4 | 10mm x 30mm x 2,5mm Flat Washers |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 4 | 10mm Lock Washers |
| 1 | Driver/Left Front Mounting Bracket | 4 | 10-1.50mm Hex Nuts |
| 1 | Passenger/Right Front Mounting Bracket | 8 | 8-1.25mm x 40mm Bolt Plates |
| 1 | Driver/Left Center Mounting Bracket | 8 | 8mm Plastic Retainers |
| 1 | Passenger/Right Center Mounting Bracket | 8 | 8mm x 24mm x 2mm Flat Washers |
| 1 | Driver/Left Rear Mounting Bracket | 8 | 8mm Lock Washers |
| 1 | Passenger/Right Rear Mounting Bracket | 8 | 8-1.25mm Hex Nut |
| 4 | 10mm L-Shapped Bolts | 12 | 8mm Combo Bolts |
| 4 | 10mm Plastic Retainers | 4 | Locking Plates |
PROCEDURE
-
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. CUTTING IS REQUIRED TO INSTALL.
-
Locate the Passenger/Front mounting location and remove the factory round rubber plug in the bottom of the outer rocker panel, (Figures 1, 2, 5 & 6).
-
Select the Passenger/Right Front Mounting Bracket, (Figure 2). Hold the mounting bracket up to the mounting location, (Figures 2 & 3). Trace the outline of the bracket onto the plastic cover where the top of the Passenger/Right Front Mounting Bracket touches, (Figure 4).
-
Move to the center mounting location. Repeat Step 3 to mark the Passenger/Right Center and Rear plastic covers. Move to the rear and repeat Step 3, (Figures 5—8).
-
Remove the plastic covers on the underside of the vehicle.
-
Cut each plastic cover along the marks to allow the Mounting Brackets clearance, (Figures 9A—10B). IMPORTANT: The covers must be cut for bracket clearance. Remove any rubber sealant that may interfere with bracket installation, (Figure 11).
-
Reattach the cut plastic covers.
-
Move to the Passenger/Right Front mounting location. Select (1) 8mm Bolt Plate. Insert the Bolt Plate into the hole in the outer rocker panel, (Figure 12A). Slide (1) 8mm Plastic Retainer onto the threads of the bolt plate to hold the bolt in position, (Figure 12C).
-
Select (1) 10mm L-Shapped Bolt, (Figure 12B). Insert the L-Shapped Bolt into the hole in the inner floor panel. Slide (1) 10mm Plastic Retainer on the threads of the bolt plate to hold the bolt in place,
(Figure 12C). -
Select the Passenger/Right Front Mounting Bracket.
- For the 10mm L-Shaped Bolt. Attach the bracket to the L-Shaped Bolt with (1) Locking Plate, (1) 10mm Flat Washer, (1) 10mm Lock Washer and (1) 10mm Hex Nut.
- For the 8mm Bolt Plate. Attach the bracket to the bolt plate with (1) 8mm Flat Washer, (1) 8mm Lock Washer and (1) 8mm Hex Nut, (Figures 13—15). Do not tighten hardware at this time.
-
Move to the Passenger/Right Center mounting location, (Figure 1). Select the Passenger/Right Center Mounting Bracket. Repeat Steps 8—10 to attach the bracket to the panels, (Figures 16 & 17).
-
Move to the Passenger/Right Rear mounting location, (Figures 1 & 18). Insert (2) 8mm Bolt Plates into the outer hole in the outer rocker panel and the inner hole in the inner floor panel. Slide (2) Plastic Retainers to hold the bolt plate in place, (Figures 12A & 19). Select the Passenger/Right Rear Mounting Bracket. Attach the bracket to the Bolt Plates with (2) 8mm Flat Washers, (2) 8mm Lock Washers and (2) 8mm Hex Nuts, (Figures 20 & 21).
-
Select and carefully unwrap the Passenger/Right Sidebar. Attach the Sidebar to the mounting brackets with (6) 8mm Combo Bolts, (Figure 22).
-
Repeat Steps 2—13 for the Driver/Left Sidebar installation, (Figures 23—25).
-
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Sidebar. Mild soap may be used to clean the Sidebar.
Passenger/Right Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>