TAC 251700 Side Steps Running Boards Installation Guide
- June 1, 2024
- TAC
Table of Contents
TAC 251700 Side Steps Running Boards
Specifications:
- Product Name: 3 Sidebars for 2017-2024 Honda Ridgeline
- Part Number: 251700
- Manufacturer: TAC Auto Parts
Product Usage Instructions
Parts Included:
- 1 Driver/Left Sidebar
- 1 Passenger/Right Sidebar
- 1 Driver/Left Front Mounting Bracket
- 1 Passenger/Right Front Mounting Bracket
- 1 Driver/Left Center Mounting Bracket
- 1 Passenger/Right Center Mounting Bracket
- 1 Driver/Left Rear Mounting Bracket
- 1 Passenger/Right Rear Mounting Bracket
- 12 8mm x 25mm Hex Bolts
- 12 8mm x 24mm x 2mm Flat Washers
- 12 8mm Lock Washers
- 12 8mm Combo Hex Bolts with washers
Installation Steps:
Step 1: Preparing for Installation
Clean the mounting areas on your Honda Ridgeline to ensure a secure fit.
Step 2: Installing the Sidebars
- Attach the front mounting brackets to the driver/left and passenger/right sides using the provided bolts and washers.
- Secure the center mounting brackets in place on both sides.
- Attach the rear mounting brackets to complete the installation.
Step 3: Post-Installation Care
After installation, wax the product to protect it. Regular waxing is
recommended to maintain the finish. Use appropriate cleaning agents for
stainless steel and gloss black finishes.
Frequently Asked Questions (FAQ):
-
Q: Can I use abrasive polish or wax on the product?
A: No, avoid using any polish or wax that contains abrasives as it may damage the finish. Use aluminum polish for stainless steel and mild soap for gloss black finishes. -
Q: How should I clean the Sidebars?
A: Use mild soap to clean the Sidebars. For stainless steel, aluminum polish can be used to address small scratches and scuffs on the finish.
INSTALLATION INSTRUCTIONS
3” SIDEBARS
2017-2024 HONDA RIDGELINE
PART# 251700
PARTS LIST
| 1 | Driver/Left Sidebar | 1 | Driver/Left Rear Mounting Bracket |
|---|---|---|---|
| 1 | Passenger/Right Sidebar | 1 | Passenger/Right Rear Mounting Bracket |
| 1 | Driver/Left Front Mounting Bracket | 12 | 8mm x 25mm Hex Bolts |
| 1 | Passenger/Right Front Mounting Bracket | 12 | 8mm x 24mm x 2mm Flat Washers |
| 1 | Driver/Left Center Mounting Bracket | 12 | 8mm Lock Washers |
| 1 | Passenger/Right Center Mounting Bracket | 12 | 8mm Combo Hex Bolts w-washers |
INSTALLATION INSTRUCTIONS
PROCEDURE:
- REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
- Starting on the driver/left front of the vehicle, locate the two factory 8mm threaded holes located in the bottom of the floor panel, (Figure 1). NOTE: Brackets install in the factory running board mounting locations. Threaded holes may be covered with insulation.
- Select the driver/left Front Bracket, (Figure 2). Attach the Bracket to the threaded holes with (2) 8mm x 25mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 2, 6 & 8). Snug but do not tighten hardware at this time.
- Move to the center of the vehicle. Locate the two threaded holes in the bottom of the floor panel and body support, (Figure 1). Repeat Steps 2 & 3 to attach driver/left Center Bracket, (Figures 3 & 8).
- Next, move to the rear of the vehicle. Locate the holes in the bottom and inner side of the floor panel,(Figure 4). Repeat Steps 2 & 3 to install the driver/left Rear Bracket, (Figures 5, 7 & 8).
- Carefully position the driver/left Sidebar onto the Brackets. IMPORTANT: Do not slide, (front to back or rotate), the Sidebar on the Brackets or damage to the finish may result. Attach the Sidebar to the Brackets with the included (6) 8mm x 25mm Combination Hex Bolts, (Figures 6—8). Do not tighten hardware at this time.
- Align the Sidebar properly and tighten all hardware.
- Repeat Steps 2—7 for the passenger/right Sidebar installation.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
-
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
-
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Sidebars.
-
For gloss black finishes: Mild soap may be used to clean Sidebars.
Driver/left Side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>