IRONBISON IB-DRS-011 Rocker Step Fits Boards Installation Guide

IRONBISON IB-DRS-011 Rocker Step Fits Boards

Product Information

Specifications

• Part Number: IB-DRS-011
• Fits: 2019-Up Dodge Ram 1500 Crew Cab (Exclude 2019-2024 RAM 1500 Classic Crew Cab)
• Installation Time: 60-120 minutes

FAQ

• Q: Do I need to drill or cut during installation?
  • A: No, cutting or drilling is not required for installation.
• Q: What tools are required for installation?
  • A: You will need wrenches in sizes 10mm, 13mm, 16mm, and 18mm, as well as Allen wrenches in sizes 4mm, 5mm, 6mm, and 8mm.

FITS

• 2019-Up Dodge Ram 1500 Crew Cab
• (Exclude 2019-2024 RAM 1500 Classic Crew Cab)

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
□ 6mm| □ 7-8.5| | □ 10mm|

| □ 4mm
■   8mm| ■          18-20| ■ 13mm| □ 5mm
□ 10mm| □ 35-40| □ 16mm| □ 6mm
□ 12mm| □ 60-70| □ 18mm| □ 8mm

BEFORE INSTALLATION

• REMOVE CONTENTS FROM BOX.
• VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST.
• READ INSTRUCTIONS CAREFULLY.
• BUMPER IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.

Part List

Installation Instructions

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE DRIVER SIDE INSTALLATION

STEP 1

• Start the installation under the Driver/Left side of the vehicle.
• Locate the front (3) factory studs along the inner side of the body panel, (Fig 1).

STEP 2

• Select (1) Front/Rear Upper Mounting Bracket (#2).
• Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts, (Fig 2). Do not tighten hardware.

STEP 3

• Select (1) Front/Rear Lower Mounting Bracket (#1).
• Attach the Lower Bracket to the short side of the Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x16mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 3). Do not tighten hardware.

STEP 4

• Move to the center location, (Fig 4). Select (1) Center Support Bracket (#4).
• Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 5).

STEP 5

• Select (1) Center Mounting Bracket (#3) and attach to the Support Bracket and upper threaded stud with (2) 8mm Flat Washers and (2) 8mm Nylon Lock Nuts, (Fig 6). Do not tighten hardware.

STEP 6

• Repeat Steps 2 & 3 to attach (1) Front/Rear Upper Mounting Bracket (#2) and (1) Front/Rear Lower Mounting Bracket (#1) to the rear mounting location, (Fig 7). Do not tighten hardware.

STEP 7

• Select the Driver/Left Rocker Step.
  • NOTE: The Driver/Left Rocker Step will have a “11-L” on the front.
  • IMPORTANT: Do not slide Rocker Step front to back on the Brackets or damage to the finish may result.
• Attach the Rocker Step to the Mounting Brackets with (6) 8mm Combo Bolts, (Fig 8). Do not tighten hardware.

STEP 8

• Level and adjust the Rocker Step and fully tighten all hardware.

STEP 9

• Repeat Steps 1—8 to attach the Passenger/Right Rocker Step.

STEP 10

• Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention

• To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
• Mild soap may be used also to clean the Rocker Step.

Customer Support: service@ironbisonauto.com
www.ironbisonauto.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>