RAVAK A224401310 Galaxy EX Shower Tray Instruction Manual

: June 3, 2024
: RAVAK

Table of Contents

A224401310 Galaxy EX Shower Tray
ASSEMBLY INSTRUCTIONS
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GALAXY
EX
PERSEUS ELIPSO MODUS GENTA
INSTALLATION INSTRUCTIONS

A224401310 Galaxy EX Shower Tray

ASSEMBLY INSTRUCTIONS

Shower Trays with Polyurethane Reinforcement – Type EX

The shower trays are perfectly compatible with all kinds of shower enclosures manufactured by the Ravak company. It is also possible to complete them with the enclosures of other manufacturers. The type EX is manufactured for direct assembly on a firm-level base. It is possible to install it either before tiling or after tiling in a finished bathroom. The surface of this tray enables identical tiling of the tray and the walls of the bathroom. When using the economical mixing set, we recommend to complete the shower tray
with the Ravak siphon with Ø 90mm.

Remove the top siphon cover using a flat, blunt object and take out the sludge trap. Using the shoulders on the inside diameter (Ø 50 mm) unscrew the siphon. Use a wrench of diameter 90 mm for the assembly.
Locate the tray provisionally in the required position and mark the location of the siphon on the floor and the height of the upper edge of the tray on the wall.
3a. Make the outlet piping Ø 40 mm and prepare the connection to the siphon. It is possible to cut off parts of the reinforcement to the maximal dimension 60X60 mm if necessary, with a rotating cutter Ø 40-50 mm.
Adjust the siphon in the tray to its correct position and mark the position of the pipe joint. Finish the connection of the outlet pipes and the siphon.
The new trays are modified for hanging from the edge to clips on the wall. It is necessary to mark the centre of the clip a quarter of the length in from the edge of the tray. Drill a hole (diameter 8 mm) 50 mm from the upper edge and fit the dowel.
For the mounting of the angular tray PERSEUS in the niche hole space out the clips (pict. 6) – 2 pcs on the back wall, on both sides 1 pc in a quarter of distance from the edge.
Screw on the plastic clip (the shorter claw up – see the picture), check the fixing of the tray.
Apply the silicone RAVAK PROFESSIONAL sealing compound on the entire surface of the tray where it contacts the floor. Apply the silicone compound on the tray approx. 10 mm from the outside bottom edge. If using an another cement there is the risk the tray will not be water-proof. Use sandpaper to roughen the bottom and side surfaces of the polyurethane support before applying the ceramic tiles to the tray.
Place the tray to in its final position and screw the siphon gently.
Press the tray against the floor and remove excessive sealing compound.
Finish the assembly of the siphon, fit on the top cover. Using the silicone sealing compound arrange the joints between the tray and floor.
The tiling can be a max. 5 mm over the outside edge of the tray. The front part of the tray can be tiled at the same time as the walls.

The Ravak company produces a special assembly pack for these installations. This pack consists of two plastic strips, a sealing foam strip, and silicone sealing RAVAK PROFESSIONAL compound. All these components are designed for reliable sealing and perfect appearance of the connection. It is possible to tile the front surface of the tray with the same tiles as on the walls in the bathroom.
Notice: Later deliveries have better packaging for protection of the trays. This is why the contact foil is no longer included. One hundred and twenty ml of sealing compound is required to seal one shower tray.

MAINTENANCE

Clean the plastic parts with a cloth and mild detergent. Never use strong cleansing or scouring agents, alcohols, thinners, or acetone. The manufacturer accepts no liability for any type of use or care other than those contained in these instructions. The manufacturer reserves the right to introduce technical changes without notice. For further information about assembly, use, and care contact your local dealer.
The manufacturer recommends: RAVAK CLEANER – works to remove old and dried-on debris from glass surfaces, shower frames, enamel and acrylic bathtubs, washbasin, and water taps; RAVAK DISINFECTANT – is a special preparation with considerable anti-bacterial and anti-fungal effects.
Ecologically dispose of the packaging materials and after the service life of the radiator is finished, properly dispose of the radiator as well. The reusable parts of the packaging materials such as the carton, tape and PE foil can be reused again instead of recycling them. The non-recyclable parts of the packaging and later, the radiator itself should be disposed of in a safe and proper manner according to law. Recycle the metal parts of the radiator by taking it to the proper recycling area.

RAVAK a.s., Obecnická 285, 261 01 Pøíbram I
tel.: +420 318 427 200, 318 427 111 fax: +420 318 427 269
e-mail: info@ravak.cz, www.ravak.com

01082019