msi MD272QXP 27 Inch Business Monitor User Guide

: June 1, 2024
: MSI

msi MD272QXP 27 Inch Business Monitor

USER GUIDE

Model: MD272QXP (3PB1); MD272QXPW (3PB1)

Introduction

This chapter provides information about hardware configuration procedures.
When connecting devices, hold them carefully and wear a grounded wrist strap to avoid static electricity.

Contents of the package

Important

If any item is damaged or missing, please contact your dealer or local distributor.

Installing the Monitor Stand

1. Place the monitor on the protective foam packaging. Fit the stand to recesses in the monitor.

2. Push the stand along the recess in the monitor until it locks into place.
3. Connect the base to the stand and tighten the screws to secure the base.
4. Before placing the monitor, make sure the base assembly is properly attached installed.

Monitor Stand

Important

The monitors hould be placed on the display.

Monitor adjustment

The adjustment features of this monitor are designed to maximize your viewing comfort.

Important

When adjusting the monitor, do not touch the display panel.
Before using pivot monitor should be tilted slightly backwards.

adjusting

Monitor overview

Connecting the monitor to your computer

1. Turn off your computer.

2. Connect the Video cable to the monitor and computer.
3. Connect the power cord to the external power supply. (Figure A)
4. Connect the external power supply to the monitor’s power port. (Figure B)
5. Plug the power cord into an electrical outlet. (Figure C)
6. Turn on the monitor. (Figure D)
7. Turn on your computer and the monitor will automatically detect the Input Source.

Connecting

This chapter provides information on configuration using the OSD menu.

Important data Allis subject to change without prior notice.

The monitor is equipped with a set of OSD menu buttons for operating the on- screen display (OSD).

OSD

Menu OSD

Important

In when receiving signals

Low Blue Light
HDCR
Brightness

HDR settings below will be grayed out:

Contrast (Kontrast)
Color Temperature (Temperatura barwowa)

Professional

Image

Input Source

Navi Key

Setting

Technical data

Preset display modes

Important: All data is subject to change without prior notice.

Preset display modes

Troubleshooting

Power LED is off.

Press the monitor power button again.
Check that the monitor power cable is connected correctly.

No picture.

Check if your computer’s graphics card is i nstalled correctly.
Check that the computer and monitor are connected to electrical outlets and tu rned on.
Check if the monitor signal cable is connected correctly.
The computer may be in standby mode. Press any button to activate the monitor.
The image is not the correct size or is not centered on the screen.
Refer to Preset Display Modes to select the appropriate setting for your monitor on your computer.

No Plug & Play support.

• Check that the monitor power cable is connected correctly.
• Check if the monitor signal cable is connected correctly.
• Check if your computer and graphics card are Plug & Play compatible.

Icons, fonts, or images are blurry, fuzzy, or have color issues.

Do not use vi deo extension cables.
Adjust brightness and contrast.
Customize RGB colors or set color temperature.
Check if the monitor signal cable is connected correctly.
Check the si gnal cable connector for bent pins.

The monitor starts to flicker or waves appear.

Change the refresh rate to suit your monitor.
Up date your graphics card dri vers.
Place the monitor away from electri cal devices that may cause electromagnetic i nterference (EMI).

Safety instructions

Read the safety instructions carefully and thoroughly.
Follow all cautions and warnings on the device or in the user manual.
Service activities may only be performed by qualified persons.

Power supply

Before connecting the device to the power socket. make sure that the power supply voltage is within safe limits and has been correctly set within the range of 100~240 V.
If the power cord has a 3-prong plug, do not remove the grounding pin. The device must be connected to a grounded socket power supply.
Verify that the on-site power distribution system is equipped with a circuit breaker rated at 120/240V, 20A (max).
Always unplug the device if it will not be used for a long time power cord or turn off the power to the wall socket to ensure zero energy consumption.
The power cord must be routed so that no one accidentally steps on it or trips over it. Do not place anything on the power cord.
If the device is used with a power adapter, please use only the power adapter provided by MSI and approved for use with this device.

Environmental conditions

To reduce the likelihood of heat-related injury or overheating, do not place the device on a soft, unstable surface or block its ventilation openings.
Use the device only on a hard, flat and stable surface.
To avoid tipping over, attach the device to a desk, wall, or solid object using an antitip mount that will secure the device and keep it in place.
Store the device away from moisture and do not expose it to high temperatures to avoid fire or electric shock.
Do not leave the device in an unventilated place with a storage temperature above 60y or below -20y, as this may damage the device.
The maximum operating temperature is approximately 40y.
Before cleaning the device, disconnect the power plug. Use a soft cloth rather than industrial chemicals to clean the device. Never pour liquids into housing openings as this may damage the device or cause electric shock.
There must be no objects with a strong magnetic or electric field near the device.
If any of the following situations occur, the device should be checked by service Personel

The power cord or plug is damaged.
Liquid has entered the device.
The device has been exposed to moisture.
The device does not function properly or cannot be started according to user manual.
The device has been dropped and damaged.
The device shows obvious signs of damage.

Specifications

Model: Modern MD272QXP (3PB1), Modern MD272QXPW (3PB1)
Version: V2.0, 2023/12
Resolution: 2560 x 1440
Refresh Rate: 100 Hz
Ports: USB Type C, HDMI, DisplayPort, USB 2.0

TÜV Rheinland certificate

TÜV Rheinland Low Blue Light Certification
Blue light has been shown to cause eye fatigue and discomfort. MSI now offers monitors with TÜV Rheinland Low Blue Light certification to ensure users’ visual comfort and well-being. Please follow the instructions below to alleviate the symptoms of prolonged work in front of a monitor and exposure to blue light.
The screen should be positioned 2028 inches (5070 cm) from your eyes and slightly below eye level.
Blinking frequently helps reduce eye strain when looking at a screen for long periods of time.
You should take 20-minute breaks every 2 hours. During breaks, focus your eyes on a distant object and look at it through something
at least 20 seconds. During breaks, push yourself to release tension or relieve body pain.
Turn on the optional Low Blue Light feature.

TÜV Rheinland Flicker Free Certificate
TÜV Rheinland has tested this product against screen flickering, which is visible and invisible to the human eye and causes eye strain.
TÜV Rheinland has developed a set of tests that define minimum standards for different frequency ranges. The test suite has been developed based on international or industry standard standards that have been increased.

The product has been tested in a laboratory according to these criteria. The phrase “flicker-free” confirms that the device does not have flicker
defined by the standard as visible or invisible flicker in the frequency range 03000 Hz at various brightness settings. Flicker-free will not occur when Anti-Flicker is turned on. image size/MPRT. (Availability of Prevent Image Size/MPRT depends on the model.)

ENERGY STAR certified
ENERGY STAR is a program of the US Environmental Protection Agency (EPA) and the US Department of Energy (DOE) aimed at promoting energy efficiency. This product qualifies for ENERGY STAR at “factory default settings” that provide energy savings. Changing the factory default image settings or enabling other features will increase energy consumption and may exceed the limits required to qualify for ENERGY STAR.

More information about the ENERGY STAR program can be found at https://www.energystar.gov/

Information regarding regulations

CE compliant
This device complies with the requirements of the Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility (2014/30/EU), the Low Voltage Directive (2014/35/EU), the ErP Directive (2009/125/EC) and the RoHS Directive (2011/ 65/EU). This equipment has been tested and found to comply with the harmonized standards for information technology equipment published in directives in the Official Journal of the European Union.

FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can produce radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Therefore, if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Rotation or displacement of the receiving antenna.
Increase the distance between the device and the receiver.
Connecting the equipment into an outlet on a circuit different from that to which the television or radio is connected.
Consult your supplier or experienced TV technician for assistance.

Note 1: Changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note 2: To comply with emission limits, only shielded AC cables and cords should be used.

This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation of the device.

WEEE declaration
Under the EU Waste Electrical and Electronic Equipment Directive 2012/19/EU, waste electrical and electronic equipment cannot be disposed of as part of municipal waste. Therefore, manufacturers of such equipment are obliged to take it back after completion