tp-link ER7406 Omada Gigabit Rackmount Desktop VPN Gateway Instructions

June 1, 2024
tp-link

tp-link ER7406 Omada Gigabit Rackmount Desktop VPN Gateway

INSTRUCTION MANUAL

FCC Compliance Information Statement

Product Name: Omada Gigabit Rackmount/Desktop VPN Gateway
Model Number: ER7406

Responsible party:
TP-Link USA Corporation
Address: 10 Mauchly, Irvine, CA 92618
Website: https://www.tp-link.com/us/
Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp- link.com/en/support/ce/

UKCA Mark

UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at https://www.tp- link.com/support/ukca/

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

Safety Information

  • Keep the device away from water, fire, humidity or hot environments.
  • Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
  • Place the device with its bottom surface downward.
  • Plug the product into the wall outlets with earthing connection through the power supply cord.
  • The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
  • The operating temperature for the device shall be within 0˚C to 40˚C (32˚F to 104˚F).

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of the device. Please use this product with care and operate at your own risk.

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product and its I.T.E. power supply. Symbols may vary from products.

Symbol Explanation
Class II equipment
Class II equipment with functional earthing
Alternating current
Direct current
Polarity of d.c. power connector
For indoor use only
Dangerous voltage
Caution, risk of electric shock
Energy efficiency Marking
Protective earth
Earth
Frame or chassis
Functional earthing
Caution, hot surface
Caution
Operator’s manual
Stand-by
ON/”OFF” (push-push)
Fuse
Fuse is used in neutral N
RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
| Caution, avoid listening at high volume levels for long periods
| Disconnection, all power plugs
m| Switch of mini-gap construction
| Switch of micro-gap construction (for US version)
Switch of micro-gap / micro-disconnection construction (for other versions except US)
| Switch without contact gap (Semiconductor switching device)

Product Specifications:

  • Model: Omada Gateway

  • Regulatory Compliance: FCC Part 15, CE Mark, EU Declaration of
    Conformity, UKCA Mark, Canadian Compliance Statement

  • Issue Date: 2024-04-17

  • Class: B

  • Compliance with: FCC Rules, EU Directives, UK Regulations, Industry Canada Standards

Frequently Asked Questions (FAQ):

1. What should I do if the device gets wet?

If the device comes in contact with water, immediately unplug it from the power source and do not attempt to use it until it is completely dry. Contact customer support for further assistance.

2. Can I mount the device on a wall?

It is recommended to place the device with its bottom surface downward as per safety guidelines. Do not mount it on a wall unless specified in the user manual.

3. How do I check for compliance marks on the device?

The compliance marks such as FCC, CE, UKCA, etc., are usually displayed on the product label at the bottom of the device. Refer to the user manual for more information.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals