BIKEBROZ Sterling Shine LED Lampen Set Instruction Manual

BIKEBROZ Sterling Shine LED Lampen Set

Product Information

Specifications:

• Brand: Sterling Shine
• Product Type: Front Light
• Light Modes: Auto, Minimum Brightness, Normal, Super Bright
• Battery Indicator: Red (needs charging), Blue (less than 20% charge), Green (fully charged)
• Charging Method: USB cable

Product Usage Instructions

1. Charging the Battery:

To charge the battery, connect the light to a power supply using the provided USB cable. The battery indicator will show green when charging is complete.

2. Assembly:

Install the rear light on the seat post using the rubber ring. For the front light, mount it securely on the handlebars to ensure it stays in place during use.

3. Switch ON/OFF and Light Modes:

Press the switch to cycle through different light modes:

• 1 press: ON/Auto mode
• 2 presses: Minimum brightness (energy saving mode)
• 3 presses: Normal brightness
• 4 presses: Super bright
• 5 presses: OFF

4. Cleaning and Care:

Clean the LED lights with a damp, lint-free cloth. Avoid submerging them in water or using harsh cleaning agents.

5. Safety Instructions:

• Do not look directly into the lights or aim them at people or animals.
• Ensure the light beam points straight ahead and does not blind other road users.
• Follow proper usage guidelines to prevent accidents or damage.

FAQ

• Q: What should I do if the battery indicator turns red?
  • A: When the battery indicator turns red, it means the battery needs to be charged. Connect the light to a power source using the USB cable to recharge it.
• Q: Can I replace the LED if it fails?
  • A: No, the LED is not replaceable. If the LED fails, you will need to replace the entire light unit.

Product description Front light

The headlight has an ambient light sensor that automatically adjusts the light intensity according to the brightness of the environment.

• Press 1 x = ON/Auto
• Press 2 x = minimum brightness (energy saving mode)
• Press 3 times = normal
• Press 4 times = super bright
• Press 5 times = OFF

If the battery indicator turns red, the battery needs to be charged.

Recharge battery

Open the cover on the back of the headlight and connect the light to the power supply using the USB cable. When the indicator lights up green, the charging process is complete.

Montage

Install the mount on the handlebars so that the headlight cannot move during normal use. If necessary, use/remove the rubber pads provided. Slide the light into the holder until it clicks.

Product description: Rear light

Recharge battery

When the charge is less than 20%, the battery indicator lights up blue. To charge, connect the light to the power supply using the USB cable. When the indicator lights up green, the charging process is complete.

Assembly

Install the rear light on the seat post of your bike using the rubber ring.

Cleaning and care

Never submerge the lights completely under water. Do not use any caustic or abrasive cleaning agents. This causes damage to the lights. Clean the LED bicycle light set with a slightly damp, lint-free cloth.

Intended Use

The device is intended for use on bicycles and is used to illuminate the road. This headlight is approved as the sole lighting on all bicycles in accordance with the currently valid StVZO. The beam of light must point straight ahead in the direction of travel and must not blind other road users. The device is intended for outdoor use. The manufacturer assumes no liability for damage resulting from improper use.

Safety instructions

• Don‘t look into the headlights.
• Do not aim the headlight directly at people or animals.
• The headlight beam must always point straight ahead in the direction of travel and must not dazzle other road users.
• The light distribution must not be obscured by any other attachments or pieces of luggage, not even – partially.
• The battery must be charged immediately when the control device?? is activated.
• The LED is not replaceable. If the LED fails, the entire light must be replaced

Safety instructions for batteries

• If a cell leaks, the liquid must not come into contact with the skin or get into the eyes. If contact occurs, wash the affected area with plenty of water and seek medical attention.
• Cells or batteries that are not designed for use with the device must not be used.
• After a long period of storage, it may be necessary to charge and discharge the cells or batteries several times in order to achieve full performance.
• Do not light the battery or expose it to combustion. Storage in direct sunlight should be avoided.

WARNING! RISK TO LIFE AND ACCIDENT TO SMALL CHILDREN AND CHILDREN!

Never leave children unattended with the packaging material, as there is a risk of suffocation if they swallow packaging parts. Always keep the device away from children. The device is not a toy!

BikeBroz GmbH | Schützenstr. 26-28

• 58339 Breckerfeld
• Tel.: +49 23 38 91 55-633
• www.bikebroz.de

References

• BikeBroz Onlineshop

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>