tp-link 7106511043 Indoor Access Point Installation Guide

: June 1, 2024
: tp-link

Table of Contents

Network Topology
Hardware Installation
Power Supply
Safety Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Guide
Indoor Access Point

Note: Images may differ from your actual product.

Network Topology

A typical network topology for the AP is shown below.

tp-link 7106511043 Indoor Access Point - Network
Topology

Some APs can be configured and monitored centrally via a controller. For details, refer to the product specifications and the manual for the relevant product or controller. You can get the controller from https://www.tp- link.com or contact the sales staff.

Hardware Installation

■ Option 1: Ceiling Mounting
Follow the steps below to install the AP with the provided accessories:
Note: The mounting bracket and the accessories (quantity and size) may vary by product.

| |
---|---|---
Washers| Pan-head Screws| Wing Nuts

Remove the ceiling tile.
Place the mounting bracket in the center of the ceiling tile. Mark positions for the screw holes and a position for the Ethernet cable hole. Drill holes for the screws and a hole for the Ethernet cable at the marked positions.
Secure the mounting bracket to the ceiling tile using pan-head screws, washers and wing nuts.
Feed the Ethernet cable through the hole and set the ceiling tile back into place.
Connect the Ethernet cable to the Ethernet port. Attach the AP to the mounting bracket by aligning the arrow mark on the AP with the arrow mark on the mounting bracket, then rotate the AP until it is locked into place.

■ Option 2: Wall Mounting
Follow the steps below to install the AP with the provided accessories:
Note: The mounting bracket and the accessories (quantity and size) may vary by product.

|
---|---
Plastic Wall Anchors| Self-tapping Screws

If your Ethernet cable feeds through the wall, position the mounting bracket and feed the Ethernet cable. Mark positions for the screw holes and then drill holes at the marked positions.
Insert the plastic wall anchors into the holes.
Secure the mounting bracket to the wall by driving the self-tapping screws into the anchors. Make sure that the shoulders of the mounting bracket are on the outside.
Connect the Ethernet cable to the Ethernet port on the AP.
Attach the AP to the mounting bracket by aligning the arrow mark on the AP with the arrow mark on the mounting bracket, then rotate the AP until it is locked into place.

Power Supply

■ Power via PSE Device or Power Adapter
Some APs can be powered via the power adapter or the PSE device (such as a PoE switch) which complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) of IEC 62368-1.
Note: Availability depends on the actual product. Please refer to the product specifications.

Via PoE Switch

tp-link 7106511043 Indoor Access Point - Via PoE
Switch

Via Power Adapter

tp-link 7106511043 Indoor Access Point - Via Power
Adapter

■ Power via PoE Adapter
Some APs can be powered via the PoE adapter.
Note: Availability depends on the actual product. Please refer to the product specifications.

tp-link 7106511043 Indoor Access Point - Power via PoE
Adapter

Safety Information

Keep the device away from water, fire, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Do not use the device where wireless devices are not allowed
Adapter shall be installed near the equipment and shall be easily accessible.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due to improper use of device. Please use this product with care and operate at your own risk.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives (EU)2015/863, 2014/53/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at https://www.tp- link.com/support/ce/

Warranty
For TP-Link Branded Products Only. For the information about warranty period, policy and procedures, please visit https://www.tp- link.com/en/support
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). TO THE EXTENT ALLOWED BY LOCAL LAW, THIS WARRANTY AND THE REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS. TP-Link warrants the TP-Link branded hardware product contained in the original packaging against defects in materials and workmanship when used normally in according with TP-Link’ s guidelines for some period which depends on the local service from the date of original retail purchase by the end-user purchaser.

For technical support, the user guide and other information, please visit
https://www.tp-link.com/support/?type=smb,
or simply scan the QR code.
© 2024 TP-Link
7106511043
REV3.0.0