HMmagnets 24 Inch 3m Magnetic Knife Holder No Drill for Wall Fridge Installation Guide
- June 1, 2024
- HMmagnets
Table of Contents
DRILL MOUNTING GUIDE | 24″ VERSION
Note: Adhesive mounting instructions are on the back side of this paper.
Parts needed for drill mounting installation:
1x One stainless steel magnetic knife bar + one carton stencil for holes
1x Two screws (4.7 X 34 mm) + two screw anchors (7.6 X 32 mm)
1x Spare set of two screws and two anchors
STEP 1: MARKING DOTS BEFORE DRILLING
Use stencil to mark two small dots for intended placement.
– The distance between the center of the two dots should be 19.88″ (50.5
CM).
– Install the bar horizontally, use of a level is recommended.
STEP 2: DRILL TWO HOLES ON THE MARKED DOTS THE SAME SIZE AS THE ANCHORS
Important Tip: Drill only one hole first. Then, using the stencil, check
that the second hole is where it should be
(1) Install the screw anchors into the holes. To prevent the bar from
wiggling, make sure the anchors are flush with the wall.
(2) Install the screws into the anchors, leaving only the head
exposed.
STEP 3: PLACE THE MAGNETIC STRIP OVER THE SCREWS
(1) Place the magnetic strip over the screws.
(2) Once on, slowly and carefully, press the magnetic bar down so the
screw heads lock into the narrow part of the holes.
(3) Once finished, if the magnetic bar is loose or wobbly, please make
sure the screw anchors are all the way in and that the screw heads are the
only parts visible. You can try screwing the screws a little deeper and
attaching the bar again and vice versa, until the bar is securely placed.
PROPER USE & WARNINGS
– The bar should be installed horizontally. Knife blades should point up.
– Recommended placement – above a hard surface (i.e. kitchen counter).
– Keep away from children.
– Pacemakers may be affected by the magnet. Keep a distance of at least 6
inches from the magnetic bar.
ADHESIVE MOUNTING GUIDE
ADHESIVE MOUNTING | 24″ VERSION
Note: Drilling mounting instructions are on the back side of this paper.
Parts needed for adhesive back mounting installation:
1x One stainless steel magnetic knife bar
5 x Small units of double-sided 3M adhesive tape
STEP 1: PREPARE INTENDED SURFACE
(1) IMPORTANT: Your les must be perfectly aligned. If some les protrude
by even 1/8 of an inch, the bar might fall.
(2) Thoroughly wipe and clean the intended surface, ensuring that all
dust, fat, oil, or any other debris is removed. Allow it to dry completely and
verify that the surface is perfectly clean. This step is crucial for ensuring
a stronger grip.
STEP 2: APPLY ADHESIVE TAPE TO THE BACKSIDE (THE SIDE WITH HOLES)
(1) BEFORE: Before peeling any layers of the 3M double-sided adhesive tape, position them on the backside of the knife bar. Arrange them side by side, aligned and centered. Ensure that the red side of the 3M tape is facing upwards. Maintain small, equal gaps between the tape units (about 1-2 mm).
(2) APPLY ADHESIVE TAPE: Begin with the first 3M tape unit and peel off
only its boom layer. Apply it to the bar’s surface (ensure you apply it to the
back side of the bar – the side with holes). Proceed to the next 3M tape unit,
applying each one carefully, one aer the other. Ensure they are aligned and
maintain equal, minimal gaps between them (about 1-2mm).
(3) AFTER: Aer you finish, apply pressure to all the tape units for 60
seconds to ensure a stronger adhesive bond.
STEP 3: APPLY THE BAR ON THE WALL AND WAIT 48 HOURS
(1) BEFORE: Before peeling the other side of the adhesive tape to mount
the bar on the intended surface, we strongly recommend placing the bar against
the wall, using a level on top to ensure it’s straight, and then marking a few
guide points for accurate mounting.
(2) APPLY THE BAR: Once your guide marks are set, peel off the remaining
layers of the adhesive tape and carefully position the bar. Avoid removing and
reapplying the bar, as this can weaken the adhesive’s strength.
(3) AFTER: Once the bar is in place, apply pressure along the enre length
of the bar for 60 seconds. Then, release and wait 48 hours to allow it to
completely dry.
PROPER USE & WARNINGS
– The bar should be installed horizontally. Knife blades should point up.
– Recommended placement – above a hard surface (i.e. kitchen counter).
– Keep away from children.
– Pacemakers may be affected by the magnet. Keep a distance of at least 6
inches from the magnet bar.
DRILL MOUNTING GUIDE
Documents / Resources
|
HMmagnets 24 Inch 3m Magnetic Knife Holder No Drill for Wall
Fridge
[pdf] Installation Guide
24 Inch 3m Magnetic Knife Holder No Drill for Wall Fridge, 3m Magnetic Knife
Holder No Drill for Wall Fridge, Magnetic Knife Holder No Drill for Wall
Fridge, Knife Holder No Drill for Wall Fridge, Holder No Drill for Wall
Fridge, No Drill for Wall Fridge, Wall Fridge, Fridge
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>