HMmagnets Size 10 Magnetic Knife Holder for Wall Fridge User Guide

Table of Contents

HMmagnets Size 10 Magnetic Knife Holder for Wall Fridge User Guide

Note: Adhesive mooning instructors are on the back side of this paper.

Parts needed for drill mounting installation:

1 x		One stainless steel magnetic knife bar + one carton stencil for holes
1 x		Two screws (4.7 X 34 mm) + two screw anchors (7.6 X 32 mm)
1 x		Spare set of two screws and two anchors

**STEP 1: MARKING DOTS BEFORE DRILLING

**

STEP 2: DRILL TWO HOLES ON THE MARKED DOTS THE SAME SIZE AS THE ANCHORS

Important Tip: Drill only one hole first. Then, using the stencil, check that the second hole is where it should be.

Install the screw anchors into the holes. To prevent the bar from wiggling, make sure the anchors are flush with the wall.
Install the screws into the anchors, leaving only the head exposed.

**STEP 3: PLACE THE MAGNETIC STRIP OVER THE SCREWS

**

Place the magnetic strip over the screws.
Once on, slowly and carefully, press the magnetic bar down so the screw heads lock into the narrow part of the holes.
Once finished, if the magnetic bar is loose or wobbly, please make sure the screw anchors are all the way in and that the screw heads are the only parts visible. You can try screwing the screws a little deeper and attaching the bar again and vice versa, until the bar is securely placed.

PROPER USE & WARNINGS

The bar should be installed horizontally. Knife blades should point up.
Recommended placement above a hard surface (i.e. kitchen counter).
Keep away from children.
Pacemakers may be affected by the magnet. Keep a distance of at least 6 inches from the magnetic bar.

Note: Drilling mounting instructions are on the back side of this paper

Parts needed for adhesive back mounting installation

1 x		One stainless steel magnetic knife bar
3 x	3M	Small units of double-sided 3M adhesive tape

STEP 1: CLEAN INTENDED SURFACE

Thoroughly wipe and clean the intended surface, making sure to remove any dust, fat, oil or any other debris.
Let it dry completely and make sure that the surface is perfectly clean. This will ensure a stronger grip.

STEP 2: APPLY ADHESIVE TAPE ON THE BAR

BEFORE: Before you peel any layers of the 3M double sided adhesive tape, place them on the backside of the knife bar, side by side, aligned and centered. Make sure the side of the red 3M tape is facing up. There should be small equal gaps between the tape units (about 1-2 mm).
APPLY ADHESIVE TAPE: Start from one side of the bar. Take the first 3M tape unit and peel only its bottom layer. Apply it to the bar surface. Continue to the next 3M tape unit, carefully applying them all, one by one. Keep them aligned and with equal minimal gaps (about 1-2mm).
AFTER: After you finish, apply some pressure on all the tape units to ensure a stronger adhesive bond.

STEP 3: APPLY THE BAR ON THE WALL AND WAIT 24 HOURS

BEFORE: Before you peel the other adhesive tape side to mount the bar on the intended surface, we strongly recommend taking the bar and using a level on top, and then mark a few guides for an accurate and straight mounting.
APPLY THE BAR: After guide marks are in place, peel all layers of the adhesive tape, and carefully apply the bac. Do not remove and re-apply the bar, this will damage the adhesive durability.
AFTER: After you finish, apply some pressure on entire bar a few times and wait 24 hours to let it completely dry.

PROPER USE & WARNINGS

The bar should be installed horizontally. Knife blades should point up.
Recommended placement – above a hard surface (i.e. kitchen counter).
Keep away from children.
Pacemakers may be affected by the magnet. Keep a distance of at least 6 inches from the magnet bar