catlike KILAUEA All Rounder Helmet User Manual

catlike KILAUEA All Rounder Helmet

Specifications And FAQ

Specifications

• Standard: EN1078:2012+A1:2012 and European Regulation 2016/425
• Activities: Pedal cycling, skateboard, roller skate
• Protection: Against low-speed falls, crashes against urban obstacles, crashes against vehicles and projectiles
• Not Suitable for: Motorsports, motorbike riding

FAQ

• Q: How often should I replace my helmet?
  • A: It is recommended to replace your helmet every three years or after any impact, even if there are no visible damages.
• Q: Can I use the helmet for motorbike riding?
  • A: No, the helmet is not suitable for motorbike riding or any other use not specified in the manual.

Using Instructions

Warning

TECHNICAL FEATURES

BEFORE USING YOUR NEW HELMET READ CAREFULLY THE INSTRUCTIONS BELOW.

1. This helmet was tested and certified according to the standard EN1078:2012+A1:2012 and European Regulation 2016/425 for Personal Protection Equipment.
   • EN 1078:2012+A1:2012 TESTING REQUIREMENTS
     TEST| DESCRIPTION OF THE TEST| RESULT
     ---|---|---
     GENERAL EQUIREMENTS| Basic construction, coverage area, and field of vision|
     IMPACT ATTENUATION| Any impact result can’t exceed 250 g|
     RETENTION SYSTEM EFFECTIVENESS| The helmet shall not come off the head| ****

RETENTION SYSTEM STRENGTH| The dynamic extension of the retention system after the test shall not exceed 35 mm and the residual extension shall not exceed 25 mm| ****

2. This helmet was designed for the following activities: pedal cycling, skateboard and roller skate. It offers protection against low speed falls; crashes against urban obstacles such as light posts, building walls, trees, and traffic signs; crashes against other vehicles and projectiles such as stones and tree branches. It must not be used in motorsports, to ride motorbikes or any other kind of use.
3. Some Catlike’s helmets are supplied with a removable visor. The application of this visor to the EPS inner shell of the helmet does not influence the shock absorption capacity of the helmet. The visor itself does not provide any kind of protection.

SAFETY INSTRUCTIONS

1. Always wear your bicycle helmet low in the front to protect the forehead, as this area is most likely to be impacted in a bicycle crash. Make sure the helmet fits and is always correctly fastened. Check the adjustment before every ride.
2. It is strictly prohibited to remove/ modify any of the original component parts of the helmet except for spare parts that might be supplied in the product packaging. The helmet must not be adapted for the purpose of fitting accessories in a way not recommended in this user manual. Such practice, besides representing a serious risk to the integrity of the user, will void all Catlike’s warranties.
3. Any helmet submitted to an impact must be destroyed and replaced even if it does not show any visible damages – The helmet shock absorption capacity might be diminished. In any case, we recommend replacing your helmet every three years or when it does not fit any longer.
4. No helmet can protect the user against all possible accidents (including those involving bicycle collisions with motor vehicles). Even accidents at low speed may result in serious injuries to the head or even death. This helmet is made to protect the head and it cannot avoid cervical or backbone injuries, or any other physical injuries resulting from an accident.

WARNINGS

• Please obey all local traffic rules to prevent accidents.
• This helmet should not be used by children while climbing or doing other activities when there is a risk of strangulation/hanging if the child gets trapped with the helmet.
• You should always fasten your buckle and tighten your chin strap before every ride. Make sure that helmet is correctly fitted and snugged to your head.
• The maximum temperature at which the helmet may be exposed is 50ºC (112ºF). Replace your helmet after exposure to higher temperatures.

HELMET FITTING

HELMET SELECTION

The helmet can only protect if it fits well. You should try different sizes and choose the size which feels secure and comfortable on the head.

ADJUSTING THE RETENTIONS SYSTEM – STRAPS

1. Adjust the strap tension so the strap fits snug by pulling the strap end through the buckle to either tighten or loosen in the adjusters as needed.
2. Open the adjuster to adjust the strap length. Do not forget to lock the adjuster afterward.
3. For models with chin padding make sure that the padding is correctly placed under your chin and fastened.

ADJUSTING THE REAR ADJUSTER

Start by opening the regulation system (rotate the mechanism anti-clockwise), put the helmet on your head and close the system, adjusting it (rotate the mechanism clockwise). To verify if the regulation system is correctly adjusted, shake your head slightly with the retention system opened – the helmet should not fall from your head.

VISOR

• Some of the Catlike helmets provided with visors include plastic caps to cover the mounting holes when the visor is removed.

CAUTION

• The mounting sockets in the helmet can be enlarged through overuse, which can cause the visor to be loose or come off unintentionally.

WARNINGS

1. The straps should not cover your ears.
2. The excess strap should be secure using the rubber “O’Ring”.
3. The buckle must be away from the chin bone.
4. To see if the strap is correctly adjusted, try to remove the helmet from the front and the back of the head. If it slides to the front, fasten the posterior belts. If it slides to the back, then fasten the interior belts.

CLEANING / MAINTENANCE / CONDITIONING

1. The helmet must be kept away from any heat source – do not leave it inside the car or any other place directly or indirectly exposed to solar radiation. High temperatures lead to the deterioration of the helmet and consequent loss of its characteristics (namely the absorption of impact energy). Heat damaged helmets may present uneven surfaces.
2. Color degradation due to solar exposure (UV exposure) will be more visible in some colors(fluorescent colors or decorations, for example) sowe recommend avoiding long sunlight exposure periods to preserve the original looks of your helmet.
3. The helmet must be hand cleaned only with water and a soft cloth. The comfort paddings should be removed from the helmet and cleaned using only water and mild soap. Use a soft cloth to dry the paddings before mounting them inside the helmet.
4. Do not use sprays or cleaning agents, chemical substances (including ammonia) and solvents to clean this helmet. They will cause the degradation of the helmet characteristics.
5. After each use, allow the helmet to air dry and then store it in a cool and dry place where it won’t get damaged.

More Information

THIS PRODUCT COMPLIES WITH THE STANDARD:

VISIT THE FOLLOWING WEB LINK TO CONFIRM YOUR HELMET EU DECLARATION OF CONFORMITY: http://bit.ly/Catlike_Declaration_Conformity

• [email protected]
• Avenida Ferreira de Castro, 818
• 3720-024 Carregosa Portugal

Designed and developed in Spain

References

• Dropbox - File Deleted - Simplify your life

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>