Lustravik 81117 LED Lamps 1W Instruction Manual
- June 1, 2024
- Lustravik
Table of Contents
Lustravik 81117 LED Lamps 1W
Specifications
- Item Number: A05036
- Voltage: 120V
- Maximum Wattage: LED, 8W
Product Usage Instructions
Tools Required:
- Ladder
- Phillips Head Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included:
- (A) Mounting plate (1)
- (B) Green ground screw (1)
- (E) Stud (2)
- (F) Canopy (1)
- (G) Lock nut (2)
- (H) Cable (1)
- (I) Steel wire (1)
- (J) Iron frame (1)
- (K) Crystal strip-A (3)
- (L) Crystal strip-B (3)
- (M) Crystal strip-C (3)
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting the installation.
- Remove the mounting plate (A) by unscrewing mounting screws (D).
- Connect wires as per the provided wiring chart.
- Tighten studs (E) onto the preassembled screws to secure thecanopy (F) in place.
Item Number: A05036
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is LED, 8W.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools
as below picture
PARTS TYPE & QTY INCLUDING
-
(A) Mounting plate (1)
-
(B) Green ground screw (1)
ACCESSORIES & QTY ENCLOSED -
(C) Plastic wire connector (3)
-
(D) Mounting screw (2)(E) Stud (2)
-
(F) Canopy (1)
-
(G) Lock nut (2)
-
(H) Cable (1)
-
(I) Steel wire (1)
-
(J) Iron frame (1)
-
(K) Crystal strip-A (3)
-
(L) Crystal strip-B (3)
-
(M) Crystal strip-C (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
-
Unscrew studs (E) from canopy (F). Remove mounting plate (A).
-
Attach mounting plate (A) to the outlet box with mounting screws (D).
-
Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connectors until tightly joined.
- Wrap each connector with approved electrical tape.
- Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
-
Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening studs (E) onto the pre-assembled screws in mounting plate (A).
-
Insert crystal strips into the corresponding positions as shown in the picture.
To adjust the hanging height of the fixture:- Press down and hold lock nut (G) by hand.
- Pull or push steel wires (I) in and out of canopy (F) to increase or decrease the hanging height.
-
Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement
parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
FAQ
Q: Can I use a higher-wattage bulb with this fixture?
A: No, the maximum wattage recommended for this fixture is LED, 8W. Exceeding
this wattage may damage the product.
Q: How do I clean the lamp?
A: To clean the lamp, use a soft, dry cloth. Avoid using acidic or alkaline
substances as they may damage the lamp’s surface.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>