Alandental AP30 Air Polishing System User Manual

Alandental AP30 Air Polishing System

Product Information

Specifications:

• Product Name: Air Polishing System
• User Manual: Included
• Usage: For polishing surfaces using air pressure

Product Usage Instructions

Safety Precautions:

Before using the Air Polishing System, ensure to follow these safety precautions:

• Wear eye protection at all times.
• Keep hands clear of the polishing area.
• Ensure proper ventilation in the working area.

Setup:

Follow these steps to set up the Air Polishing System:

1. Connect the system to a compatible air compressor.
2. Fill the reservoir with the appropriate polishing solution.
3. Adjust the air pressure according to the surface being polished.

Usage:

Once the system is set up, follow these steps for usage:

1. Aim the nozzle towards the surface to be polished.
2. Press the trigger to release the polishing solution along with compressed air.
3. Maintain a consistent distance and angle for uniform polishing.

FAQ

• Q: How do I clean the Air Polishing System after use?
  • A: To clean the system, disconnect it from the air compressor, empty the reservoir, and rinse all components with water thoroughly.
• Q: Can I use any polishing solution with this system?
  • A: It is recommended to use compatible polishing solutions specified for use with the Air Polishing System to ensure optimal performance and longevity.

Introduction

Customer satisfaction is critical to our company’s quality policy. This series of products are in accordance with the relevant legal requirements, quality standards, and industry standards for the development and manufacture, and For the safety of your patients and before you use it for the first time, please read the instructions. These instructions will describe how to use your product and how to ensure it works smoothly and effectively.

Product Usage

It’s used for cleaning teeth and removing calculus and tartar. Improper use may damage the air scalp machine and may result in a risk to the patient, the user and the third party.

Applications

• Plaque removal for placement of sealants
• Surface preparation prior to bonding/cementation of inlays,onlays, crowns and veneers
• Surface preparation prior to placing composite restorations
• Cleaning prior to bonding orthodontic brackets
• Effective plaque and stain removal for orthodontics patients
• Clean implant fixture prior to loading
• Stain removal for inaccessible parts of the usual cleaning
• Plaque removal prior to fluoride treatment
• Plaque and stain removal prior to the whitening procedure
• Surface polishing prior to regular cleaning.

Contra-indication

Patients suffering from chronic bronchitis or asthma must not, under any circumstances, be treated with this device. The jet of air and powder could cause respiratory difficulties.

Features

• Even in high pressure, the handpiece can have 360-degree free rotation, offering a more considerate and flexible treatment.
• Stains and plaque can be efficiently cleaned by the free attached clean powder, which assures a relaxed and pleasant treatment to both the user and the patient

Safety Precautions

• Please read the following warnings, precautions and operation instructions.
• These safety instructions are to avoid potential injury to people or damage to the device. According to the risk seriousness, safety instructions are classified as below.

To north ut be is only by trained and qualified personnel (dentist or dental hygienist)

1. Those with respiratory illness
2. Those in the treatment of more than 3 mm pocket depth or have an injury in the mucous membrane. Due to the long time jetting near the soft tissues or the salivary gland, powder can be introduced into the injury. In extremely rare cases, this would increase the risk of emphysema.
3. Those with grave ulcers in digestive in organs.
4. Those with hepatic dysfunction.
5. Those with lung or cardiac dysfunction.
6. Those with damage or abnormality in the oral cavity.
7. Those with hyperemia, hemorrhage, or inflammation in the oral cavity.
8. Those that tend to develop inflammation or ulcers in the oral mucous membrane.
9. Those with allergens.
10. Those with contact lenses.
11. Depending on the patient’s habitus, In extremely rare cases, it may cause allergy or stomatitis. In case of these symptoms, stop using this unit immediately.
12. For those that require a restriction on sodium intake (patient with hypernatremia, pregnancy toxemia, kidney deficiency, chronic respiratory disease or chronic diarrhea), Classic Cleaning Powder would cause the over-intake of sodium and deteriorate the disease.
13. Sodium hydroxide clean powder can cause excessive sodium intake leading to the deterioration of the situation uf things

• The user keeps wearing eye protection and a safety protection mask during treatment. The patient wears eye protection. Sucking the filling powder during operation is recommended. In case of eye contact, clean your eyes with plenty of water and consult an oculist immediately.
• Do not directly jet the powder toward the margin of the cementum, decal filed enamel, and lings, molars,and crowns etc.
• Application of Vaseline etc,on the patient’s hips before treatment will prevent them from becoming dry and chapped.
• Excess recommended rated air pressure might result in cracks in the powder case and cap and cause injury
• Use only clean and dry compressed air. Moisture or oil in the air might cause sodification of the powder.
• Tighten the powder cap, Never take off the cap during treatment.
• Make sure all connection parts are absolutely dry before connecting the powder case.
•  Use original powder only. In case of damage resulting from using powder of other manufacturers.
• All residual powder in the case must be discarded after the operation. Reuse the powder may cause clo g
• Make sure the powder bottle cap is promptly tightened after the fillings. Long tire exposure may result in powder cake and cause clog.

Operating the unit

• The patient is allowed to wash mouth as often as needed to avoid a long and continuous treatment;
• Do not impact or hit the case or the cap as this could cause a scratch or crack;
• Done operating the up rise martin, one tug he or lo of has pice break the connection
• Only operate this unit under correct air pressure;
• Scour or blow dry all the internal and external components before operation.
• Care should be exercised at all times to prevent powder from entering the human mucous area (eg. eyes, nose etc.) except the mouth, Besides, use the towel to protect factor use eye protection to prevent the powder from getting into eyes.
• The contact lenses of the patient should be taken off before treatment;
• Clean adhering chemicals and oil etc. On the case and the cap, keep away from such items as they may cause fault

Air Pressure

• A Sets air pressure the host cruise mile 5-0. 5a i 25. 4.5 and the cap, and the finally cause injury.

Connecting the hose connector to the powder case

Dry thoroughly the quick connector, handpiece, hose connector, end connector of the case, interior of the case, nozzle inside the case and the cap.
keep operating the unit after shutting off the water supply system to below residual out of the tubes.

Connecting the handpiece to the powder case

Pull full back the tapered circle in the front connector of the powder case, Directly push the handpiece to the powder case connector till the end, and then release the tapered circle (refer to Figure 1). Gently pull the handpiece to make sure a correct connection

Filling clean powder in the powder case

Setting the optimal water flow rate

• It is easier to set the water flow rate before using the unit for the first time while the powder case is empty, set the water flow rate from your handpiece to obtain a uniform spray.

Filling the powder case

• Make sure that the powder chamber is absolutely dry, Moisture can cause the powder to cake
• Use only powder provided by our company. use powders from other manufacturers might cause tube clog and adversely affect its efficiency due to different powder size
• Open the case cap prior to the bottle ap. Fill in the powder, screw the bottle cap immediately.
• Make sure the nozzle hole is not covered with powder before screwing on the cap.
• Clean the threads of the case before screwing on the cap
• Make sure the cap is tightened up;
• Do not shake the device as this could cause the powder to clog the tubes.

Using the unit

Handing and setting water and compressed air Familiarize yourself with the use of the unit by cleaning a yellow coin or an extracted or extracted tooth, you can modulate the result according to the adjustments.

• Increasing the air pressure increases the cleaning effect and reduces the polishing effect.
• Increasing the water flow rate increases the polishing effect and reduces the cleaning effect.

Wear a mask and eye protection:

• The contact lens or glasses the patient may get dirty during the treatment, we recommend taking them.
• To limit the risk of bacterial or viral infections and inhalation of powder,we recommend that the dentist and the hygienist to wear a safety protection mask.

•The nozzle should never be pointed toward the patient before, or during the after the operation. Before treatment, the patient rinses with mouthwash for at least 30 seconds, will greatly prevent the development of bacteria in the mouth during treatment Before the treatment, patients with Vaseline-coated lips. After the patient will prevent the lips from becoming chapped during treatment. Cotton roll placed under the lip place a large swallow of saliva with powder, separate lips and teeth, and protect the gums.

Treatment:

•  Position the pump for sublingual aspiration
• The extraction in a high-speed dental chair deviated from the treatment to drain the excess powder and water mixture.
• The handpiece and the high-speed evacuator must be handled by the same operator
• Aim the nozzle al the evacuator inlet and jet for 2 to 3 seconds to verify that the good liquidity of powder and water is used in the dental surface.
• When using nozzle 3 from the tooth surface to 5mm with an angle of 10 degrees to 80 degrees injection
• During treatment, make small circular motions Finally after the keratin ent polish all dental
• Surface by setting the water flow rate to the maximum

After the treatment, the teeth are clean and the dental cuticle is completely eliminated.It’s reconstitution by salivary proteins requires between 2 and 3 hours. During this time, the teeth do not have any more natural protection with respect to coloring.

• Tell your patient that during 2 to 3 hours following treatment, he should neither smoke nor consume food or drink that could strongly color the teeth (tea, coffee…) Release the pedal and wait until the spray stops
• When removing the foot from the control pedal, the air/powder jet continues for a few more seconds, Take these seconds into account. You can also introduce the nozzle still in the patient’s mouth into the high-speed evacuator. •Let some time for the unit to decompress, with no risk of damaging the patient’s mouth.

Maintenance

Powder disposal

• Organic solvent adhering on the cap may result in cracks.
• Powder cases are a consumption item. It will deteriorate by ultraviolet rays, or by other environmental factors, Replace the case every six months.
• Clean thoroughly the case,the cap, and their threads once a week. Check for cracks in the case and the cap.
• If you notice cracks in the case or the cap, replace either of the items immediately,use the product under this situation may result in cap cracks. Debris of the cap may cause injury to the user or patient.
• Clean by ultrasound once a week to avoid clogs.
• In the case of any fault, please contact the authorized dealer for repair.
• Clean thoroughly the interior and exterior of the unit after the treatment to make sure all the powder residue is removed. This unit must be stored in an absolutely dry place.
• Do not use any lubrication equipment. But the o-ring must be lubricated by the equipped sealing oil.

1. Uncover the cap, Empty the powder chamber
2. Keep operating the unit after shutting off the water supply system. Blow residual moisture and powder out of the tubes.
3. Blow residual powder in the case with the dry compressed air.
4. Scour saliva and other debris on the nozzle and handpiece head with an alcohol-immersed soft cloth.

Disconnecting the hose, powder case, handpiece and nozzle

1. Screw the hose
2. Pull back the tapered circle, and take of the handpiece
3. Install the blowing nozzle in the hose connector, and connect to the handpiece to operate the unit without a water supply for over 5 seconds.(Figure 2)
4. Hang on the blown part during air-blowing

Cleaning

1. Clean the interior of the handpiece connector and the o-ring on the case connector with equipped cleaning brush (Figure 3).

1. In case of the powder adherence on the o-ring, take of the o-ring and clean it carefully as well a its groove (Figure 4)
2. Take of the rubber sealing ring, and remove the plastic part of the cap (Figures)
3. Rinse the powder & adhere on the case and the cap. (Figure 6)
4. Dry and assemble the powder cap(powder cap includes transparent can rub her sealing o-ring and the can hase)

in case of powder residual in the case, the powder would cake and might cause a clog

Lubrication

1. Dry the o-ring of the case connector. Drop the equipped sealing lube oil on the o-ring, and even up the oil by hand (Figure 7)
2. Sterilized in high temperature and high pressure

Cleaning and Disinfecting

Submerge only the handpiece in a disinfectant bath,Do not submerge the case and the cap in a disinfectant bath.

Ultrasonic Cleaning

Make sure the unit is cleaned by ultrasound once a week to avoid clog
1 . Disassembling and cleaning.
2. Use an equipped wrench to screw out the nozzle.
3. Clean the nozzle with hot water by ultrasound
4. Blow water of all parts with dry compressed air after the cleaning •
5. Connect the tubes, Shut off the water supply system, Uncover the cap, and Blow water out of the tubes.

Dry thoroughly all the parts especially the interior of the case

Disinfecting

• Sterilization in high temperatures and high pressure is recommended. This unit must be disinfected after the first use and each treatment.
• All the components are able to be sterilized by high temperature and high pressure. Sterilization procedure.

1. Disassembling and cleaning;
2. Enclosed n a sterilization ag;
3. Sterilizable at up to 135°C in the auto clave (autoclave for 20min,at 121°C or 1 5min at 1 32°C)
4. Keep the handle in the sterilization bags, until you open it, when using it apart, reassemble the apparatus to remove the reverse order.

• According to ENI3060 or EN ISO 17655-1 requested, we suggest sterilization in high temperature and high pressure at 121 °C, at least more than 15 minutes.
• Dry thoroughly all the parts before operation;
• Take of the cap before sterilizing in high temperature and high pressure;
• Sterilize the semitransparent part of the cap may cause damage;
• Chemical liquid adhering on the unit while sterilization may cause damage to its coating or affect the internal parts. Thus, be careful that chemical liquid should not be brought to the autoclave.
• The temperature near the heater would exceed the given temperature in the autoclave. Do not place this unit near heat sources.
• Do not clean or scour this unit by a high-acidity cleanser or disinfectant.

Warranty

The warranty will be valid for one year from the date of purchase of your product and accessories.
Damages due to non-adherence to the operation instructions or wear out of parts are excluded from the warranty.
The warranty of your product will be cancelled if you try open it.

Note : The manufacturer reserves the right to modify the technique, accessories, operating instructions or contents of the set without making anv notification in advance.

About the Symbols

Technical Data

Troubleshooting

In case of any fault that cannot be solved by the above methods, please contact with your dealer

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>