OPPSK 04-HYT LED Moving Head Light User Manual

OPPSK 04-HYT LED Moving Head Light

Before You Begin

What In the Box :

•  1 x Moving Head Lights
• 1 x Power Cable
• 1 × Bracket
• 2x Screw
• 1 × IR Remote Controller
• 1 x User Manual

Unpacking Instructions:
Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.

Caution: There are no user-serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In the unlikely situation, that your unit may require service, please contact us: info@oppsk.com

Disclaimer:
OPPSK believes that the information contained in this manual is accurate in all respects. However, OPPSK assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage, or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident, or any other cause. OPPSK reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, OPPSK has no obligation to make and does not commit to make any such revisions.

Safety Notes:

• Please keep this User Manual for future consultation.
• Unpack and check carefully there is no transportation damage before using the fixture.
• Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
• It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
• Disconnect main power before servicing and maintenance.
• Use a safety chain when fixing this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
• Maximum ambient temperature is Ta: 104°F/40°C. Don’t operate it where the temperature is higher than this.
• In the event of a serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
• Do not connect the device to any dimmer pack.
• Do not touch any wire during operation and there might be a hazard of electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
• The housing must be replaced if they are visibly damaged.
• Do not look directly at the LED light beam while the fixture is on.

Introduction

Product Overview & Size

Setup

AC Power:

The Moving Head DJ Light has an auto-ranging power supply and it can work with an input voltage range of 110 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.

Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Introductions.

Operation

Control Panel Operation:
To access the control panel functions, use the four buttons located underneath the display.

System Menu

Chad

| 20CH

24CH

| 20 Channel Mode

24 Channel Mode

Send

| nast

d512

| Master

Slave

 |  | -6-
Shnd| Sh 1-4| Sound Control Mode 1-4
---|---|---

Auto

| Aut 1-4| Auto Mode 1-4
Sp 1-9| Auto Speed 1-9
Sens| 0-99| Sound Sensitivity 0-99

Led

| On| LED Display On
Off| LED Display Off
dlSP| dlSP| LED Display Flip

Pan

| No| X Motor Forward Rotation
Yes| X Motor Reversal

Tilt

| No| Y Motor Forward Rotation
Yes| Y Motor Reversal
Ver| V10| Current Software Version
Rset| Res| Reset

DMX Mode 1: 20CH

CH19

| ****

Strobe

| 0-9| No Function
10-139| Strobe 0-100%
140-255| Random Strobe Speed

CH20

| ****

Master Mode Selection

| 0-9| Manual Dimming
10-199| Auto Mode
200-209| Wait for 2S to reset
210-239| Manual Dimming
240-255| Sound Mode

DMX Mode 2: 24CH

CH21

| ****

Color temperature selection/ manual dimming (channel 17 0-14 valid)

| 0-35| Manual Dimming
36-255| 10 color temperature adjustment

CH22

| ****

Manual dimming/ color selection/ color temperature selection

| ****

0-14

| Manual Dimming or Color Temperature Selection
---|---|---|---
15-255| Color Selection

CH23

| ****

Strobe

| 0-9| No Function
10-139| Strobe 0-100%
140-255| Random Strobe Speed

CH24

| ****

Master Mode Selection

| 0-9| Manual Dimming
10-199| Auto Mode
200-209| Wait for 2S to reset
210-239| Manual Dimming
240-255| Sound Mode

DMX Connection:

Set the product in DMX mode / A001 to control with a DMX controller.

• Connect the product to a suitable power outlet
• Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket on the product.

IR-C Remote Operation

Note: 1-9 static colors can not be adjusted by up and down keys to adjust the brightness

TECHNICAL SPECIFICATIONS

• Light Source: ( LED ): 40W
• Voltage : AC110-240V, 50/60Hz
• LED BALL: 1pcs*10W 4in 1 RGBW LEDs
• LED SMD: 36pcs SMD 0.2W RGB 3IN1
• Pan/Tilt movement: X-axis: 540°, Y-axis: 270°
• LED BALL Angle : 2°
• Dimmer : 0-100% linear dimming
• Operation Modes: Auto, DMX512, Sound, Master/Slave
• Channel : 20/24CH
• Package Size : 8.5×6. 1×7.1inch / 21.5×15.6x18cm
• Weight : 1.55kg / 3.42lbs

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>