CUCULIDAE Y52CAC3018R-CH-BL 52 Inch Derocate Ceiling Fan User Guide

CUCULIDAE Y52CAC3018R-CH-BL 52 Inch Decorate Ceiling Fan

Product Information

Product Specifications:

• Model: Y52CAC3018R-CH/BL
• Brand: CUCULIDAE
• Size: 52-inch
• Type: Decorative Ceiling Fan

Product Usage Instructions

Installation of the Hanging Bracket:

Concrete Ceiling:

1. Switch off the electrical mains at the circuit breaker fuse box.
2. Use the Mounting Bracket as a guide to mark the spots for drilling 4 holes.
3. Drill holes using an 8mm percussion bit.
4. Insert Expansion Bolts and secure the hanging bracket using Flat Washers, Spring Washers, and Nuts.

Wooden Ceiling:

1. Switch off the electrical mains at the circuit breaker fuse box.
2. Use the Mounting Bracket as a guide to mark the spots for drilling 4 holes.
3. Drill holes for 3mm diameter Self Tapping Screws.
4. Secure the hanging bracket using Washers and Self Tapping Screws.

Pre-Installation:

Fastening the Blade Arms to the Motor:

• Remove pre-installed screws from the motor.
• Install fan blades onto corresponding screw holes and fix them with the removed screws.

Assembly – Attaching the Lights:

• Connect white and blue lines from the motor to corresponding lines from the light kit using insulated rubber tape.
• Attach arms to the fan-motor assembly by inserting an alignment post into the slot on the motor and tightening screws.
• Repeat for remaining blade assemblies.

Finish:

• Take the wire into the switching box of the motor.
• Align the opening of the switching box of the light with the rotation of the motor’s switching box.
• Install downrod assembly by feeding motor wires through and tightening collar setscrews.
• Slip the coupling cover, canopy cover, and canopy onto the downrod.

Making the Electrical Connections:

Warning:
Ensure correct wire sizes are used for connections. Consult an electrician if needed.

Frequently Asked Questions

Q: Can this ceiling fan be installed on a sloped ceiling?

A: Yes, this ceiling fan can be installed on a sloped ceiling using a sloped ceiling adapter (not included).

Q: Can I use a remote control with this ceiling fan?

A: Yes, you can use a compatible remote control with this ceiling fan for added convenience. Make sure to follow the remote control pairing instructions provided with the remote.

Q: What is the recommended height for installing this ceiling fan?

A: The recommended height for installing this ceiling fan is typically between 7 to 9 feet above the floor for optimal air circulation.

What’s In The Box

Parts Kit

Fastening the blade arms to the motor

• Remove the pre-installed screws
• Install the fan blade on the corresponding screw hole, and then install and fix it with the removed screws.

• Fasten the arm to the fan-motor assembly by inserting the alignment post into the slot on the bottom of the motor and tightening the pre-installed armscews.
• Repeat this step for the remaining blade assemblies.

Assembly-Attaching the Lights

• Insert the “white” line in the switching box of the motor into the “white” line of the light and tie insulated rubber tape.
• Insert the “blue” line in the switching box of the motor into the “blue” line of the light and tie insulated rubber tape.

• Take the wire into the switching box of the motor.
• Align the opening of the switching box of the light at the switch locking position of the positive and negative rotation of the motor switching box.
• Place the cover screw in the screw of the switching box.

Installation of the hanging bracket

For concrete ceilings, use the percussion bit with a diameter of 8mm to drill holes according to the length of the expansion screws. Then use the attached expansion screws to fix the hanging bracket onto the ceiling (the selection is made according to the actual requirements of the customers).

STEP 1 A-CONCRETE CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

1. Use the Mounting Bracket as a guide, and mark the spots where the 4 Expansion Bolts will be drilled.
2. Remove the Mounting Bracket, drill 2 holes and insert 2 Expansion Bolts into the concrete ceiling, install the mounting bracket and secure it with Flat Washers, Spring Washers and Nuts.

IMPORTANT: SCREWS & NUTS MUST BE TIGHTENED TILL SNUG
For the wooden ceiling, use wood screws to drill on the wooden beam or the “junction box” to fix the hanging bracket(selection is made according to actual requirements of the customers)

STEP 2 A-WOODEN CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.

1. Use the Mounting Bracket as a guide, and mark the spots where the 4 Self Tapping Screws will be drilled.
2. Remove the Mounting Bracket, drill 4 holes for 3diamondand and r, and install the mounting bracket the onto wooden ceiling with the 4Self Tapping Screws &Washers

Install downrod assembly

• Carefully feed the motor wires up through the downrod
• Align the holes and replace the hanger pin and locking pin.
• Tighten the two colar setscrews.
• the Slip coupling cover, canopy cover and canopy onto the downrod.

Hang the fan
Lift the fan motor assembly to the mounting bracket and seat the hanger ball in the mounting bracket socket. Rotate the fan motor assembly until the check groove drops into the registration slot and seats firmly. The downrod should not rotate if the is done correctly

Install canopy

• Ensure the loosened screws are inserted into the keyholes on the mounting bracket.
• Carefully raise the canopy to the mounting bracket. Rotate the canopy clockwise.
• Secure the canopy by replacing the screws previously removed and tightening the screw previously loosened
• Place the canopy cover (if applicable)and rotate the canopy cover clockwise until it locks into position.

Making the electrical connections

• WARNING: Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. If you have large than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use.
• IMPORTANT: Use the plastic wire connectors(BB) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.
• WARNING: Remove the rubber motor stops on the bottom of a fan before installing the blades or testing the motor.
• WARNING: Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan.
• If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use.
• WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor.
• IMPORTANT: Use the plastic wire connectors(BB) supplied with your fan. Secure the connectors with electrical tape and ensure there are no loose strands or connections.

SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX

1. Connect wires from receiver to the terminal block properly as instruction diagram

Preparing for mounting

Install remote control

1. Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
2. Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.

Preparing for mounting

1. Remove the mounting bracket from the canopy by loosening the two canopy screws located in the L-shaped slots
2. Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket

Use of remote control

• LOW FanSpeed Low Level
• MED FanSpeed Middle Level
• HI FanSpeed High level
• STOP FanSTOP

LIGHT ON/OFF

• 1H Auto off after 1hr
• 2H Auto off after 2hr
• 4H Auto off after 4hr
• 8H Auto off after 8hr

If you have any questions, please feel free to contact us.

• Email: hdteam@aminalife.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>