CUCULIDAE Y52DAC4001R-CH-BL 52 Inch Derocate Ceiling Fan User Guide
- June 15, 2024
- CUCULIDAE
Table of Contents
- CUCULIDAE Y52DAC4001R-CH-BL 52 Inch Decorate Ceiling Fan
- Product Information
- Product Usage Instructions
- Pre-Installation
- Fastening the blade arms to the motor
- Assembly-Attaching the Lights
- Installation of the hanging bracket
- Install downrod assembly
- Making the electrical connections
- Preparing for mounting
- Use of remote control
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CUCULIDAE Y52DAC4001R-CH-BL 52 Inch Decorate Ceiling Fan
Product Information
Specifications
- Model: Y52DAC4001R-CH/BL
- Brand: CUCULIDAE
- Size: 52 inches
Product Usage Instructions
Installation of the Hanging Bracket
To install the hanging bracket, follow the steps below:
For Concrete Ceiling (Step 1)
- Switch off the electrical mains at the circuit breaker fuse box.
- Use the mounting bracket as a guide and mark the spots where the 4 expansion bolts will be drilled.
- Remove the mounting bracket and drill 2 holes for the expansion bolts into the concrete ceiling.
- Install the mounting bracket and secure it with flat washers, spring washers, and nuts. Make sure to tighten the screws and nuts until snug.
For Wooden Ceiling (Step 2)
- Switch off the electrical mains at the circuit breaker fuse box.
- Use the mounting bracket as a guide and mark the spots where the 4 self-tapping screws will be drilled.
- Remove the mounting bracket and drill 4 holes for 3mm diameter.
- Install the mounting bracket onto the wooden ceiling with the 4 self-tapping screws and washers.
Pre-Installation
Before installing the fan blades and lights, make sure to complete the
following steps:
- Fasten the blade arms to the motor using the provided screws.
- Attach the lights by inserting the white and blue lines from the motor’s switching box into the corresponding lines of the light. Secure them with insulated rubber tape.
- Fasten the arm to the fan-motor assembly by inserting the alignment post into the slot on the bottom of the motor and tightening the pre-installed arm screws. Repeat this step for the remaining blade assemblies.
Finish
Complete the installation by following these steps:
- Take the wire into the switching box of the motor.
- Align the opening of the switching box of the light at the switch locking position of the positive and negative rotation of the motor switching box.
- Place the cover screw in the screw of the switching box.
- Install the downrod assembly by carefully feeding the motor wires up through the downrod.
- Align the holes and replace the hanger pin and locking pin.
- Tighten the two-collar setscrews.
- Slip the coupling cover, canopy cover, and canopy onto the downrod.
Making the Electrical Connections
When making the electrical connections, please note:
WARNING: Each wire not supplied with this fan is designed to accept up to one 12-gauge house wire and two wires from the fan. If you have larger than 12-gauge house wiring or more than one house wire to connect to the fan wiring, consult an electrician for the proper size wire nuts to use.
FAQ
- Q: What should I do if I have any questions or need assistance?
- A: If you have any questions or need assistance, please feel free to contact us at hdteam@aminalife.com.
Pre-Installation
Parts Kit
NOTE : HarHardwdwarare not shown to actual size not shown to actual size. e.
Fastening the blade arms to the motor
- Remove the pre-installed screws
- Install the fan blade on the corresponding screw hole, and then install and fix it with the removed screws.
- Fasten the arm to the fan-motor assembly by inserting the alignment post into the slot on the bottom of the motor and tightening the pre-installed armscews.
- Repeat this step for the remaining blade assemblies.
Assembly-Attaching the Lights
- Insert the “white” line in the switching box of the motor into the “white” line of the light and tie insulated rubber tape.
- Insert the “blue” line in the switching box of the motor into the “blue” line of the light and tie insulated rubber tape.
- Take the wire into the switching box of the motor.
- Align the opening of the switching box of the light at the switch locking position of the positive and negative rotation of the motor switching box. Place the cover screw in the screw of the switching box.
Installation of the hanging bracket
CÖNCRETE CEILING
For concrete ceilings, use the percussion bit with a diameter of 8mm to
drill holes according to the length of the expansion screws. Then use the
attached expansion screws to fix the hanging bracket onto the ceiling (the
selection is made according to the actual requirements of the customers).
STEP 1 A-CONCRETE CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
- Use the Mounting Bracket as a guide, and mark the spots where the 4 Expansion Bolts will be drilled.
- Remove the Mounting Bracket, drill 2 holes, insert 2 Expansion Bolts into the concrete ceiling, install the mounting bracket, and secure it with Flat Washers, Spring Washers, and Nuts.
IMPORTANT : SCREWS & NUTS MUST BE TIGHTENED TILL SNUG
For wooden ceiling, use wood screws to drill on the wooden beam or the “junction box” to fix the hanging bracket(selection is made according to actual requirements of the customers)
STEP 2 A-WOODEN CEILING
SWITCH OFF THE ELECTRICAL MAINS AT THE CIRCUIT BREAKER FUSE BOX.
- Use the Mounting Bracket as a guide, and mark the spots where the 4 Self Tapping Screws will be drilled.
- Remove the Mounting Bracket, drill 4 holes for 3MM diameter, install the mounting bracket onto wooden ceiling with the 4Self Tapping Screws &Washers
Install downrod assembly
- Carefully feed the motor wires up through the downrod
- Align the holes and replace the hanger pin and locking pin.
- Tighten the two-collar setscrews.
- Slip coupling cover, canopy coverand canopy onto the downrod.
Hang the fanHang the fan
- Lift the fan motor assembly to the mounting bracket and seat the hanger ball in the mounting bracket socket. Rotate the fan motor assembly until the check groove drops into the registration slot and seats firmly. The downrod should not rotate if the is done correctly
Install canopy
- Ensure the loosened screws are inserted into the keyholes on the mounting bracket.
- Carefully raise the canopy to the mounting bracket. Rotate the canopy clockwise.
- Secure the canopy by replacing the screws previously removed and tightening the screw previously loosened
- Place the canopy cover (if applicable)and rotate the canopy cover clockwise until it locks into position.
Making the electrical connections
WARNING :
Each wire not supplied with this fan is designed to accept up to one 12-gauge
house wire and two wires from the fan. If you have large than 12-gauge house
wiring or more than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
IMPORTANT :
Use the plastic wire connectors(BB) supplied with your fan. Secure the
connectors with electrical tape and ensure there are no loose strands or
connections.
WARNING :
Remove the rubber motor stops on the bottom of a fan before installing the
blades or testing the motor.
WARNING :
Each wire not supplied with this fan is designed to accept up to one 12-gauge
house wire and two wires from the fan. If you have larger than 12-gauge house
wiring or more than one house wire to connect to the fan wiring, consult an
electrician for the proper size wire nuts to use.
WARNING :
Remove the rubber motor stops on the bottom of the fan before installing the
blades or testing the motor.
IMPORTANT :
Use the plastic wire connectors(BB) supplied with your fan. Secure the
connectors with electrical tape and ensure there are no loose strands or
connections.
Preparing for mounting
Install remote control
- Carefully push the canopy to the bottom of the mounting bracket, make two sliding holes aligned to the two prominent screws on the mounting bracket, and then turn clockwise until tight.
- Push the canopy ring to the bottom of the canopy, slide the inner holes aligned to the two prominent screws on the mounting bracket again, and turn the canopy ring clockwise until tight.
Preparing for mounting
- Remove the mounting bracket from the canopy by loosening the two canopy screws located in the L-shaped slots
- Remove and save the two canopy screws in the round holes. This will enable you to remove the mounting bracket. This will enable you to remove the mounting bracket
Use of remote control
- FanSpeed Low Level
- FanSpeed Middle Level
- FanSpeed High level
- FanSTOP
LIGHT ON/OFF
- Auto off after 1hr
- Auto off after 2hr
- Auto off after 4hr
- Auto off after 8hr
If you have any questions, please feel free to contact us. Email : hdteam@aminalife.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>