SUNCO LIGHTING PRE-90105 Brass Smooth Hooded Landscape Pathway Light Instruction Manual

June 1, 2024
Sunco Lighting

SUNCO LIGHTING PRE-90105 Brass Smooth Hooded Landscape Pathway Light

UNCO-LIGHTING-PRE-90105-Brass-Smooth-Hooded-Landscape-Pathway-Light-
fig-1

Product Specifications

  • Fixture Type : Low voltage luminaire
  • Maximum Power: 25A, 15V
  • Transformer: Remote transformer required
  • Main Cable Installation: Buried for less than 6 inches underground

Product Usage Instructions

Luminaire Mounting (with PVC Spike)

  1. Run wire pigtail from luminaire through the mounting hole in the top of the PVC Spike.
  2. Thread PVC Spike into the fixture.
  3. Place PVC Spike in the desired position and insert into the ground until flange of PVC spike is flushed to grade level.
  4. Attach fixture(s) wires pigtail to main supply cable with connector suitable for direct burial (not provided).
  5. Provide power to the luminaire and check proper operation.

Lamp Replacement

  1. To prevent electrical shock, disconnect transformer from electrical supply before service.
  2. Remove lens cover to expose lamp.
  3. Replace lamp with correct wattage and type marked on fixture label. Replace lens cover.
  4. Note: DO NOT touch lamp with bare hands. Always use a soft cloth to handle lamps.

Specifications subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.

Frequently Asked Questions (FAQ)

  • Can I use a power unit with more than 25A for this fixture?
    No, it is recommended to use a maximum of 25A, 15V power unit for this fixture to avoid damaging the luminaire.

  • Do I need any special tools for lamp replacement?
    You do not need any special tools for lamp replacement, just ensure to use a soft cloth to handle the lamps and prevent any damage.

PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION. Please read the instructions before you install and use the luminaire.

  • Turn circuit breaker(s) off or remove fuse(s) before installation.
  • Fixture(s) must be installed in accordance with all local codes and ordinances.
  • DO NOT install within 10 feet of a pool spa or fountain.
    SUITABLE FOR MOUNTING WITHIN 4 FT OF THE GROUND.
    SUITABLE FOR WET LOCATIONS.

SAFETY INFORMATION

TO REDUCE THE RISK OF FIRE, OR INJURY TO PERSONS:

  • Turn off/unplug and allow to cool before replacing lamp.
  • Lamps get hot quickly. Contact only switch plug when turning on.
  • Do not touch hot lens, guard or enclosure.
  • Keep lamp away from materials that may burn.
  • Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
  • Do not operate the luminaire fitting with a missing or damaged shield.
    SAVE THESE INSTRUCTIONS
    WARNING DISCONNECT POWER BEFORE INSTALLING OR SERVICING.

LUMINAIRE MOUNTING (with PVC Spike)

  1. Run wire pigtail from luminaire through the mounting hole in the top of the PVC Spike.
  2. Thread PVC Spike into the fixture.
  3. Place PVC Spike in the desired position and insert into the ground until flange of PVC spike is flushed to grade level.
  4. Attach fixture(s) wires pigtail to main supply cable with connector (not provided) suitable for direct burial.
  5. Provide power to the luminaire and check the proper operation.

UNCO-LIGHTING-PRE-90105-Brass-Smooth-Hooded-Landscape-Pathway-Light-
fig-2

LAMP REPLACEMENT

  1. To prevent electrical shock, disconnect transformer from electrical supply before service.
  2. Remove lens cover to expose lamp.
  3. Replace lamp with correct wattage and type marked on fixture label. Replace lens cover.
    Note: DO NOT touch lamp with bare hands. Always use a soft cloth to handle lamps.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Sunco Lighting User Manuals

Related Manuals