MyosHome Sonoma Oak and Gray Console Hallway 90 x 30 x 87 cm with Two Zeus Drawers Instruction Manual
- June 1, 2024
- MyosHome
Table of Contents
MyosHome Sonoma Oak and Gray Console Hallway 90 x 30 x 87 cm with Two Zeus
Drawers Instruction Manual
| LISTA DE P1EZAS | QTY |
|---|---|
| 1 | PANEL SUPERIOR |
| 2 | PANEL INFERIOR |
| 3 | PANEL LATERAL( I) |
| 4 | PANEL LATERAL(D) |
| 5 | PANEL CENTRAL |
| 6 | FRONTAL CAJON (D) |
| 7 | FRONTAL CAP(I) |
| 8 | LATERAL CAJON (I) |
| 9 | LATERAL CAJON (D) |
| 10 | TRASERA CAJON |
| 11 | BASE CAJON |
| HERRAJES | |
| --- | --- |
| A | Wet Al A2 |
| B | EVIGA |
| C | **COPIFIRMAT** | 10 PCS |
| D | LLAV E ALLEN |
| E | 3.S X IMAM TORMLLO |
| G | 4 X SOMA TORNILLO |
| H | CLAV 0 |
| I | TAPA DE PLASTIC° |
| AF | IL1442 /4/04DLE TORNILLO |
| BD | PtASTIC DOW EL ** |
| ** | 2 PC |
| BO | “CU ADRA |
| BR | TIRADOR |
| CD | GUIAS METALICAS C c.0 O2 |
PAQUETE:
1/1 1,2,3,4,5,6,7,8,9,10,11, Paquete de herrajes
DESTORNILLADOR
MARTILLO
TALADRO
Before assembly, read the instructions carefully and follow them step by
step.Read the instructions carefully. See the list of furniture parts and the
list of hardware to orient. Be sure to have all the pieces before starting to
assemble.
Place and mount the furniture on a flat and clean surface, such as a carpet or
a mat to prevent it from being ray
-
Remove the screws and separate the lower panel from the side panels
-
Remove the minifixs and separate the side panels from the lower panel.
-
Insert the A2 hardware into the panel (1,6,7). Insert the B tools in the panel (1,6,7)
-
Set the panel (1) to the panel (3,4,5). Insert the A1 hardware on the panel (3,4,5). Turn all A1 until they are tight.
-
Connect the bottom panel to the side panel using hardware C
-
Connect the drawer sides to the drawer rear panel using the hardware C.
-
Set the panel (6.7) to the panel (8 ,, 9). Insert the A1 hardware on the panel (8.9). Turn all A1 until they are tight.
-
Insert the rear panel (11) into the side panel of the drawer (8.9).
-
Set the lower drawer panel (11) on the edge of the panel (8.9) with nails (H).
-
Connect the handle (BR) to the panel (6,7) using the AF hardware.
-
The product consists of two parts. Press the unlock lever to separate the elements from the guide.
-
Connect the drawer guides (CD1) to the side panel of the drawer using the hardware and
-
Join the drawers of the drawers (CD2) to the vertical panels by means of the hardware E
-
Insert the drawer by the sliding slot until it fits.
-
Join the squad to panel (2) with the hardware E.
-
Join the metal leg to the upper panel through the hardware E.
-
Make a mark on the wall with a pencil starting from the level of the corner piece
-
Perforas the walls of the wall with a drill.
-
Place the tacos on the wall.
-
Set the squad to the plastic spike with the G.
